Question about Cars & Trucks

Open Question

1984 Dodge D250 318 V8 starter installation

Detail starter removal and installation steps

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

ZJLimited
  • 17970 Answers

SOURCE: neeed to take apart steering shaft on 93 dodge

Starter - REMOVAL & INSTALLATION on Gasoline Engines
(see Figures 13, 14, 15, 16, 17, 18, 19 and 20)

zjlimited_1627.jpg

Fig. 13: Disconnect the wires attached to the starter solenoid to facilitate removal

  1. Disconnect the negative battery cable.
zjlimited_1628.jpg

Fig. 14: Unbolt the starter from the vehicle

  1. Remove the cable from the starter.
zjlimited_1629.jpg

Fig. 15: Once detached, remove the starter from the vehicle

zjlimited_528.gif

Fig. 16: Exploded view of the starter mounting-2.5L engine

  1. Disconnect the solenoid leads at their solenoid terminals. If necessary, tag then to avoid confusion when re-installing.
zjlimited_529.gif

Fig. 17: Attach the starter wire connector to the terminals as shown-V6 and V8 engines

zjlimited_1630.jpg

Fig. 18: To remove the starter, unbolt the mounting hardware shown-V6 and V8 engines (click image for zoom)



On 4WD Dakota models with the V6 engine, the starter is removed from above. On these models you will have to disconnect the steering gear and position the shaft out of the way to gain working clearance.

  1. Remove the starter attachment bolts and withdraw the starter from the engine flywheel housing. On some models with automatic transmissions, the oil cooler tube bracket will interfere with the starter removal. In this case, remove the starter attachment bolts, slide the cooler tube bracket off the stud, and then withdraw the starter.
zjlimited_1631.jpg

Fig. 19: When detached, pull the starter away from the engine and remove it from the vehicle-2WD Dakota model shown (click image for zoom)



To install:

  1. Be sure that the starter and flywheel housing mating surfaces are free of dirt and oil to make a good electrical contact.
zjlimited_1632.jpg

Fig. 20: Install the starter motor on the 4WD Dakota from above as shown

  1. Slide the starter in place, secure using the bolts and washers removed. Tighten the bolts to 50 ft. lbs. (68 Nm). Connect wires and battery cable end at the starter.
  2. If removed for clearance, reconnect the steering column shaft.
  3. Secure the oil cooler bracket if equipped. Connect the negative battery cable on the battery.
When tightening the mounting bolt and nut on the starter, hold the starter away from the engine for the correct alignment.


REPAIR PROCEDURE:
This bulletin involves release of a new repair package for the steering coupler with a revised boot design.

Remove and discard the existing cover and seal.
Disassemble the coupler and inspect the shoes, shoe retaining spring, internal bearing surfaces of the coupler body, and the shaft pin for evidence of wear. Replace any worn components.
Fill the coupler body 1/2 full with Multipurpose Grease, NGLI Grade 2 EP, such as MOPAR P/N(NNN) NNN-NNNNor equivalent.
Place the boot and clamp on the shaft.
Press the shoe pin onto the steering shaft so that it projects equal distance on the shaft.
Place the spring on the side of the shaft, straddling the shoe pin.
Place the shoes on the pin ends with the flat side towards the spring, engaging the tangs.
Squeeze the shoes together, compressing the spring, and push the assembly into the coupler body with the master spline on the upper shaft.
Drive in the NEW dowel pin flush with the outer surface of the coupler body.
Position the boot on the body and install the clamps on both ends. Be sure that the contact surfaces are free of grease.
Work the shaft in and out several times to distribute the grease in the assembly


Hope this helps.

Posted on Jul 26, 2011

ZJLimited
  • 17970 Answers

SOURCE: How to remove a fuel filter in a carburetor 1984 pontiac parisienne? V8 Gasoline

Acording with 1984 PONTIAC PARISIENNE 5.0L 4BL OHV 8CYL - REPAIR GUIDE, This system incorporates a bleed in the pressure regulator which automatically relieves pressure any time the engine is turned off, but a small amount of fuel may be released when the fuel line is disconnected.

To reduce the chance of personal injury, cover the fuel line with a shop cloth to collect the fuel, and then place the cloth in an approved container.

The Fuel Filter is located under hood, center, upper engine area, mounted in fuel inlet line connected to carburetor.

Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice weekend.

Posted on Nov 19, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change starter 1984 dodge rampage


How do I remove the starter on a 1984 dodge rampage? It is really hard to get to.

Jul 05, 2012 | Dodge Rampage Cars & Trucks

1 Answer

Need an emissions schamatic for my 1984 K10 silverado 305 engine


Unfortunately, there are 13 variations for this engine and year. Was this truck sold or modified for high altitude? Was it sold in California or modified to meet the CA emission standards? Does it have a manual or auto transmission? After narrowing down based on answers to these questions, there are still alternative configurations depending on the particular equipment, so look carefully at the diagrams to see which components are used on your engine. Sometimes you can match the 3 letter code for the diagram to letters in the VIN or a sticker in the engine compartment. Please let me know if you have questions.


jturcotte_2426.gif

Fig. Fig. 49: 1984 305 (5.0L) V8 engine-4bbl federal and low altitude with automatic transmission

jturcotte_2427.gif

Fig. Fig. 50: 1984 305 (5.0L) V8 engine-4bbl federal and low altitude with automatic transmission alternate

jturcotte_2428.gif

Fig. Fig. 51: 1984 305 (5.0L) V8 engine-4bbl federal and high altitude with automatic transmission

jturcotte_2429.gif

Fig. Fig. 52: 1984 305 (5.0L) V8 engine-4bbl federal and high altitude with automatic transmission alternate

jturcotte_2430.gif

Fig. Fig. 53: 1984 305 (5.0L) V8 engine-4bbl federal and high altitude with manual transmission

jturcotte_2431.gif

Fig. Fig. 54: 1984 305 (5.0L) V8 engine-4bbl federal and high altitude with manual transmission alternate

jturcotte_2432.gif

Fig. Fig. 55: 1984 305 (5.0L) V8 engine-4bbl federal and low altitude with manual transmission

jturcotte_2433.gif

Fig. Fig. 56: 1984 305 (5.0L) V8 engine-4bbl federal and low altitude with manual transmission alternate

jturcotte_2434.gif

Fig. Fig. 57: 1984 305 (5.0L) V8 engine-4bbl federal and low altitude with manual transmission alternate

jturcotte_2435.gif

Fig. Fig. 58: 1984 305 (5.0L) V8 engine-4bbl federal and low altitude with automatic transmission alternate

jturcotte_2436.gif

Fig. Fig. 59: 1984 305 (5.0L) V8 engine-4bbl federal and high altitude with automatic transmission alternate

jturcotte_2437.gif

Fig. Fig. 60: 1984 305 (5.0L) V8 engine-4bbl federal and low altitude with automatic transmission alternate

jturcotte_2438.gif

Fig. Fig. 61: 1984 305 (5.0L) V8 engine-4bbl federal and high altitude with automatic transmission alternate

Oct 27, 2011 | Cars & Trucks

1 Answer

Starter removal 1990 audi quattro v8


1990 Audi V-8 Quattro 3.6L DOHC

Starter, removing and installing

Disconnect battery NEGATIVE cable
Disconnect wiring from battery to starter and starter to alternator (large terminal)
Disconnect terminal 50 (small wire to ignition/starter switch)
Remove starter mounting screws on engine/transmission
NOTE: Remove upper bolt on starter by guiding 10 mm Allen socket with extension and flex fitting through opening on transmission housing over final drive
Remove starter motor assembly
Reverse procedure to install

Oct 10, 2011 | 1990 Audi V8 Quattro

1 Answer

I need to replace starter motor in my 2000 Toyota Tundra 4.7 L V8. Do I need to remove the upper and lower plenum?


No you do not need to remove the plenums. The starter is removed and installed from underneath the truck of from within the wheel well if the wheel is removed. You should go buy a Haynes or Chilton repair manual for $20 they are indisposable to do it yourselfers and will give detailed step-by-step instructions with pictures.

May 12, 2011 | 2000 Toyota Tundra

1 Answer

1984 dodge charger. how to i get to the starter



Starter - REMOVAL & INSTALLATION
The starter is an overrunning clutch drive type with a solenoid mounted on the starter motor. Six different type starters are used on these models. Two each are built by Nippondenso, Bosch and Mitsubishi for manual and automatic transaxle applications. Removal and installation procedures are the same for all units. Some early production models may experience starter motor damage due to improper fit of the upper and lower steering column shrouds. Irregularities in the mating surface of the key cylinder area may cause the ignition key to bind, causing the starter to be continuously engaged. The condition can be corrected by loosening the shroud cover screws about 1 1 / 2 turns.
If loosening the screws does not solve the problem, the covers will have to be replaced with new parts, which are available only in black and must be painted to match interior trim.



  1. Disconnect the negative battery cable.
  2. If equipped, remove the heat shield.
  3. On the 2.2L loosen the air pump tube at the exhaust manifold, then swivel the bracket away from the starter.
  4. Remove the wires from the starter and solenoid.
  5. Support the starter, remove the bolts and lift the unit out from the flywheel housing.
  6. Installation is the reverse of removal.
22281f5.jpg

Fig. 1 Starter mounting on the 1.6L engine (click for zoom)

50cdf32.jpg

Fig. 2 Mounting for the 1.7L engine with A-412 manual transaxle

4252200.jpg

Fig. 3 Mounting on the 1.7L engine with the A-404 automatic transaxle

08554c3.jpg

Fig. 4 Mounting for the 1.7L A-460 manual transaxle and the 2.2L manual or automatic transaxle




Hope this help; remember comment and rated this.

Aug 03, 2010 | 1984 Dodge Ramcharger

1 Answer

I have an old car but it very old it a 1984 and have a problem to take out the starte so can you please explain me how to do it


Disconnect the battery. To find the starter trace the wire from the battery and it will go to the starter. Disconnect the wires from the starter (make a note of which wire goes where) then remove the two bolts and the starter will come off. Make sure you purchase a new solinoid (bendix) with the new starter.

Mar 05, 2010 | 1984 Dodge Caravan

1 Answer

1984 Dodge D150 Pickup Truck V8 Electrical Problem, altonator is not putting out to keep the Battery charge. The altonator and senors have been replaced. Thanks Ken. kmkmbm@yahoo.com


Have your battery load tested. Be sure belt is not slipping . Abnornal battery draw (aftermarket accessories) or parasitic battery draw when shut off. Chrysler sells a high amp alt. for you truck.

Nov 28, 2009 | 1984 Dodge D150

1 Answer

Internationl 345 v8 torque settings


Head bolt torque: 90-100 ft lbs., to be reached in 3 equal tightening steps, below is the sequence:
9 3 1 6 8
Front of vehicle
7 5 2 4 10

Main bearing cap torque: 75-85 ft lbs.
Rod bearing cap torque: 45-55 ft lbs.
Looks like u've been busy, and will be for a while. Good Luck!

Nov 15, 2008 | 1984 Dodge D150

1 Answer

Dodge ram 1500 v8


go to an auto parts store like autozone and buy a chilton's or haynes repair manual specific to the make/model of your vehicle. they are about $20. these books will walk you through your repair step by step. either manual is good, i prefer chiltons because i found it to offer greater detail with repair.

Jun 06, 2008 | 1997 Dodge Ram 3500 Club Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

126 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...