Question about 1996 Toyota Land Cruiser
Posted by Anonymous on
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
You need a coil spring compresser, and the proper skill level to use it.
If you try to change the coils without a compresser, you CAN & WILL GET HURT. Coil springs are not something to fool about with if you do not have the proper tools. These things are danagerous.
Posted on Sep 09, 2008
SOURCE: Front door panels
yes you need to remove the door panel and here is the instructions via TIS (Toyota info system)
1. REMOVE THESE PARTS:
Tape a screwdriver tip before use.
(a) Door inside handle bezel
(c) Armrest panel base upper
(d) Courtesy light
(e) Lower frame bracket garnish
2. REMOVE DOOR TRIM
(a) Remove the 3 screws from the door trim.
(b) Using a screwdriver, remove the clip and remove the trim
by pulling all of the trim up.
Tape the screwdriver tip before use.
(c) Remove the 11 screws and armrest base from the door
(d) Remove the inner weatherstrip from the door trim.
(e) Remove the 8 screws and door pocket from the door trim.
3. REMOVE THESE PARTS:
(a) Door belt moulding
Pry out the clip from the edge of the panel, and remove the
(b) Door weatherstrip
Do not pull strongly on the weatherstrip as it may tear.
(c) Door inside handle
(d) Door lock control relay
(e) Service hole cover
BODY − FRONT DOOR
Do not block the trim clip sealing with the tape.
(f) Outside rear view mirror
(g) Door glass run
(h) Rear lower frame
Adjust the equalizer arm up to down and tighten if where dimensions
A and B, as shown are equal.
(i) Door glass
(j) Window regulator
Torque: 5.0 N·m (50 kgf·cm, 43 in.·lbf)
Apply MP grease to the sliding surface and gears of the window
Do not apply grease to the spring.
(k) Locking and opening control link
(l) Door lock
Apply adhesive to the 3 screws.
Part No.08833−00070, THREE BOND 1324 or equivalent
Torque:5.0 N·m (50 kgf·cm, 43 in.·lbf)
BODY − FRONT DOOR
At the time of reassembly, apply MP grease to the sliding surface
of the door lock.
(m) Door outside handle
(n) Door lock cylinder
(o) Door speak
Posted on Mar 09, 2009
The starter motor is buried in the V8 valley . It is about a days work to replace it . They are very expensive , have only a few service parts and don't like water .
Posted on Aug 02, 2010
SOURCE: I need to remove the
When you open the door, you will see a small cover that covers the mirror inside, remove the cover then use screw driver to loose the screws and remove the mirror and replace it.
Posted on Aug 20, 2011
Tips for a great answer:
Feb 02, 2018 | Cars & Trucks
Jun 22, 2016 | Cars & Trucks
Aug 20, 2014 | Cars & Trucks
Mar 14, 2014 | Toyota Cars & Trucks
Jul 30, 2012 | Cars & Trucks
Aug 20, 2011 | Toyota Land Cruiser Cars & Trucks
May 22, 2010 | 2000 Toyota Land Cruiser
Jul 03, 2009 | 1995 Toyota Land Cruiser
Jul 30, 2008 | 2004 Toyota Land Cruiser
145 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: