Question about Oldsmobile Aurora

Open Question

Olds 4.0 belt routing - Aurora Oldsmobile Cars & Trucks

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How simple is it to change a alternator belt on subaru svx?


  1. Removing the Serpentine Belt
    • 1 Park your Subaru on a level surface and open the hood.
    • 2 Disconnect the ground (black) battery cable using a wrench. This will prevent the cooling fan from activating.
    • 3 Locate the serpentine belt routing diagram in your engine compartment and compare it to the actual routing of the installed belt. Make sure the routing on the label matches the actual routing. If they do not match or there is no label, note the actual routing on a piece of paper for later reference.
    • 4 Locate the belt tensioner pulley on your Subaru model. If the tensioner is equipped with a squared hole, use a large breaker bar with a 1/2-inch (13 mm) drive. Otherwise, use a ratchet and socket of the proper size on the tensioner pulley center bolt.
    • 5 Rotate the tensioner pulley away from the belt to release the belt tension.
    • 6 Pull the belt off of one of the pulleys and slowly release the tensioner pulley back into position. Do not let the tensioner pulley snap back or you may damage an internal component.
    • 7 Finish removing the serpentine belt from the rest of the pulleys and the engine compartment.
    Installing the New Serpentine Belt
    • 1 Match the old belt to the new one and make sure they are of the same length and configuration. It is normal for the new belt to be slightly shorter since the old one has been stretched through use.
    • 2 Route the new serpentine belt through all of the pulleys except the tensioner pulley. Use the diagram on the engine compartment or your notes, as a reference, to properly route the belt.
    • 3 Insert the large breaker bar into the square hole or the ratchet and socket into the tensioner pulley center bolt.
    • 4 Rotate the tensioner pulley in the same direction you did to release the belt tension.
    • 5 Slide the serpentine belt onto the tensioner pulley.
    • 6 Release the tensioner pulley back into position.
    • 7 Look at all the pulleys and make sure the serpentine belt is properly seated on each one. Otherwise, release the belt tension and adjust the belt.
    • 8 Connect the ground (black) battery cable using the wrench.

Oct 18, 2011 | 1992 Subaru SVX

1 Answer

Serpentine belt diagram for a 2003 Chevy unpalatable 4.3


Pop the hood of the car and locate the serpentine belt routing diagram. The diagram on the 2003 Chevrolet Impala is on top of the fan shroud. The diagram will be a picture of all of the accessory pulleys and how the serpentine belt is routed among the pulleys. This diagram will give you the exact direction for routing the new belt onto the pulleys. If you cannot find a serpentine belt routing diagram, take a notepad and pen and draw out the exact routing diagram of the old belt across the pulleys.

  • 2 Locate the serpentine belt tensioner. It is located below the alternator on the left front side of the engine. The tensioner on the 3.4 liter, 3.5 liter and the 3.9 liter engines will require a 3/8 ratchet to release the belt tensioner. The 3.8 liter engine will require a ratchet and a 15 mm socket for the belt tensioner. Rotate the belt tensioner clockwise to loosen and remove the belt from the belt tensioner pulley.
  • 3 Slide the old belt from the belt tensioner pulley. Remove the belt from the remaining pulleys and pull the belt from the engine compartment.
  • 4 Route the new belt across the crankshaft pulley first. The crankshaft pulley is the big pulley on the bottom of the engine in the center. Then route the serpentine belt across the remaining pulleys as directed by the serpentine belt routing diagram. Leave the belt tensioner pulley for last.
  • 5 Rotate the belt tensioner clockwise again to relieve the tension and slide the new belt across the top of the belt tensioner pulley. Release the belt tensioner and the belt will tighten up as the tensioner applies pressure to the belt. Make sure the new belt is properly seated in all the pulleys.
  • 6 Crank the engine and inspect the belt again to make sure that it stays seated in the pulleys.

  • Read more: How to Replace a Serpentine Belt on a 2003 Chevrolet Impala ' eHow.co.uk http://www.ehow.co.uk/how_6120665_replace-belt-2003-chevrolet-impala.html#ixzz1Yi6QLAjb

    Sep 21, 2011 | 2003 Chevrolet Impala

    1 Answer

    I need a belt routing diagram for 2009 Tacoma 4 liter


    Timing belt routing diagrams for cars and trucks? Click the link below:--- http://technoanswers.blogspot.com/2011/10/timing-belt-routing-diagrams-for-cars.html

    Drive belt routing diagrams for cars and trucks? Click this link below:--- http://technoanswers.blogspot.com/2011/10/drive-belt-routing-diagrams-for-cars.html

    Jul 25, 2011 | 2009 Toyota Tacoma

    2 Answers

    Need a diagram for a 99 toyota corolla serpentine belt


    • Here is the serpentine diagram for a 1999 Toyota Corolla with and without AC.

    ironfist109_31.gif


    • Thank you for using FixYa

    Regards, Tony

    Jun 19, 2011 | Toyota Corolla Cars & Trucks

    2 Answers

    Drivebelt came off while on the highway (about 75 mph). Towed it home, went to replace belt and now both old belt (4 yrs old) and new belt (both 1025) are too long. Put on 1015 belt, topped off anti-freeze...


    Hi, when a belt comes off, it's usually because of a bad bearing in one of the accessories or idler pulleys, or maybe your tensioner spring is broken. Remove the belt and check all pulleys for spin and play. It is also possible you lost an idler pulley and the new belt routing is not turning the water pump in the right direction. Check the routing and look for a missing idler pulley. Let me know if you are missing the routing diagram.

    Feb 21, 2011 | 1988 Oldsmobile Delta 88

    2 Answers

    Where is the ac compressor located on a 2002 xl7 suzuki above or below the engine


    It depends on the engine size for the belt routing.

    Click on the "x" for the diagrams on the following engine sizes:
    FIRING ORDER AND BELT ROUTING Firing Order and Belt Routing X90, Vitara & Grand Vitara Fig. 1: 1998 1.6L engine Firing order: 1-3-4-2 Distributor rotation: Counterclockwise 79243g34.gif
    Fig. 2: 1999-02 1.6L engine Firing order: 1-3-4-2 Distributorless ignition system (coils over No. 2 and 4 cylinders) 93023g03.gif
    Fig. 3: 2.0L engine Firing order: 1-3-4-2 Distributorless ignition system (one coil over each cylinder) 93023g05.gif
    Fig. 4: Accessory V-belt routing- 1.6L engine with A/C 93024g03.gif
    Fig. 5: Accessory V-belt routing-1.6L engine with A/C and P/S 93024g04.gif
    Fig. 6: Accessory V-belt routing-1.6L engine with P/S 93024g05.gif
    Fig. 7: Accessory serpentine belt routing-1.8L and 2.0L engines 93024g07.gif
    Fig. 8: Accessory V-belt routing-1.8L and 2.0L engines 93024g08.gif
    Fig. 9: Accessory V-belt routing-2.5L engine with P/S 93024g09.gif
    Fig. 10: Accessory V-belt routing-2.5L engine with A/C and P/S 93024g10.gif

    Sep 02, 2010 | 2002 Suzuki XL-7

    2 Answers

    How to adjust de belt to grand cherokee 8 cilinders 4.7


    1. Step 1 Find the belt tensioner pulley. The tensioner pulley is generally between the crankshaft and a component toward the top of the hood area.
    2. Step 2 Check the belt routing so you know how to replace the belt. You may be able to find a belt routing diagram on a decal on the fan shroud or in support documentation. Otherwise, make you own sketch for reference.
    3. Step 3 Rotate the belt tensioner pulley, using the wrench, to and relieve tension on the belt.
    4. Step 4 Slip off the old belt and slowly release the tensioner pulley.
    5. Step 5 Use your belt routing diagram to put the new belt onto all of the pulleys. Pay close attention to the water pump pulley, as incorrect routing can cause the water pump to run backwards and overheat.
    6. Step 6 Make sure the belt is correctly routed and seated on all pulleys. Rotate the tensioner again to allow for the belt to slip onto all pulleys and then release the tensioner again to regain correct tension on the belt.

    Jun 01, 2010 | 1999 Jeep Grand Cherokee

    2 Answers

    How to route the serpentine belt


    if you buy your belt from Autozone the routing is on the package

    Dec 26, 2009 | 2001 Ford Escort ZX2

    2 Answers

    Replacing serpentine belt on 1991 mustang 5.0 I changed the alternator but i can't get the belt back on.


    Are you using the old belt or a new one? Just make sure the belt is the right one. There is only one right way to route the belt. There should be a diagram of the belt routing on the fan shroud or hood. If you can't find it, I've had some luck doing an internet search for the right routing diagram.

    Sep 19, 2009 | 1991 Ford Mustang

    1 Answer

    Driveability


    several things come to mind 4 this your belt is old n stretch out ur belt tensior is bad or the pully on supercharger is locking up or the belt isnt routed rt n these are pain to route on these cars

    Jun 14, 2008 | 2000 Pontiac Grand Prix

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    13 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Oldsmobile Experts

    yadayada
    yadayada

    Level 3 Expert

    75744 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8123 Answers

    Are you an Oldsmobile Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...