Question about 2004 Chevrolet Aveo

Open Question

2004 aveo torque spec for inner tie rod - 2004 Chevrolet Aveo

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 9 Answers

SOURCE: chev avalanche 2004 inner tie rods

I was able to fix the inner tie rod problem with a little of patients and 90 bucks for the parts. When I took it in for the front end to be aligned the drivers side was only off by 1/4 on an inch.

Posted on Nov 08, 2008

Ad
  • 141 Answers

SOURCE: inner tie rods

if it is a rak and pionin sterring yes

Posted on Jan 13, 2009

  • 462 Answers

SOURCE: what torque spec for chev aveo 2004 cylinder head

18 lb ft+60°+60°+60°+10°

NEW HEAD BOLTS ARE REQUIRED WHEN REPLACING THE HEAD OR HEAD GASKET.

Posted on Jul 04, 2009

mychkelbey
  • 12 Answers

SOURCE: 2005 malibu maxx ball joint and lower control arm torque specs

A Ball Joint Can Usually Be Replaced Without Removing The Control Arm From The Vehicle. Place The Vehicle On Jack Stands. Remove The Shock Absorber And Install A Spring Compressor on The Coil Spring.Remove The Nut Securing The Ball Joint To The steering Knuckle And Separate The Knuckle And Then Joint. The Ball Joint Should Be Pressed,Riveted,Bolted,Or Screwed Into The Control Arm.A Service Manual Will Give The Details For The Specific Make And Model Vehicle.

Posted on Apr 09, 2010

reisdos
  • 1297 Answers

SOURCE: need the torque specs for

hope this helps...

4c17033.jpg

2c46aed.jpg

Posted on May 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Inner tie rod end torque specs


not enough info year make and model

Jan 18, 2016 | Cars & Trucks

1 Answer

Torque specs for castle nut and lock nut to inner tie rod


tighten tight by hand then line up the cut out in the castle nut to the hole in the tie rod and insert cotter pin and bend pin so it will not come out.

Aug 01, 2015 | Cars & Trucks

1 Answer

What is the torque for inner tie rod end on a 2000 for focus


59 ftlbs

Hope this will answer your question,If do pls click on helful botton and you can follow me at fixya,so I can answer your question faster.thanks.

Mar 10, 2015 | 2000 Ford Focus

1 Answer

What is the torque specs for a tie rod end on a 1994 toyota camry


The tie rod end adjusting nut, 54 ft lb or 74 Nm
The tie rod end ball joint nut, 36 ft lb or 49 Nm

May 10, 2014 | 1994 Toyota Camry

1 Answer

Tire rod end left sidefrom gearbox is broken how do i dismantel


if its the outer tie rod than loosen the jam nut on the threaded part of the inner tie rod. You will then be able to unthread the outer tie rod from the inner. Count the number of turns and install the new one with the same number of turns.

If its the inner tie rod you will need an inner tie rode remover/installer tool and a torque wrench.

Feb 03, 2012 | 2001 Mercury Sable

1 Answer

How to install inner and outer tie rods on a 2004 Chrysler Pacifica - I waqs told buy a trusted local mechanic that I need to replace 3 of the 4 tie rods. Might as as well replace all 4, but how hard is it...


You will need to rent or borrow in inner tie rod tool but here are the directions.
1. Break the jam nut on inner tie rod to outer loose.
2. Remove nut from outer tie rod attaching it to steering knuckle.
3. Use hammer to get tie rod out of knuckle.
4. Unscrew outer tie rod then jam nut
5. Remove clamp from boot and slide off inner tie rod.
6. Using side cutter or hammer and chisel break off metal clamp on the inside of inner tie rod boot.
7. Using inner tie rod tool, unscrew inner tie rod from rack and pinion
8. Reinstall parts and have it aligned

May 06, 2010 | 2004 Chrysler Pacifica

1 Answer

How does it come apart


The inner tie rod assembly just unthreads like a bolt, if you have the proper tool. After paying $117.49 for this gold plated tool i discoverd they are loaned out by some parts stores. if you ask. By the way the torque spec for the tie rod is 70 ft lbs.

Nov 11, 2009 | 1999 Chevrolet Lumina

1 Answer

What torque spec for chev aveo 2004 cylinder head


18 lb ft+60°+60°+60°+10°

NEW HEAD BOLTS ARE REQUIRED WHEN REPLACING THE HEAD OR HEAD GASKET.

Jul 04, 2009 | 2004 Chevrolet Aveo

1 Answer

Need torque spec for 2000 Cirrus outer tie rod ends


45 Ft-lbs Tie-rod balljoint stud-to-steering knuckle nut, and 55 Ft-lbs Tie-rod (outer)- to- inner jam lock nut

Apr 04, 2009 | 2000 Chrysler Cirrus

Not finding what you are looking for?
2004 Chevrolet Aveo Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...