Question about 2007 BMW X3 3.0si SAV

Open Question

Bmw 328i light out indicator turned on but cant find the problem

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

ginko
  • 19396 Answers

SOURCE: 328i BMW, and the EML light is on

Sometimes you can reset the engine warning light by disconnecting the battery for ten minutes or more (be sure you have your stereo unlock code if needed).
That is not a good solution, it is better to diagnose and eventually fix the problem.
Have the car computer scanned with a code reader, the codes you get in return witll tell you exactly where to find the problem.

Here is the code list.

To get the codes the code reader must be connected to the car computer.


sometimes on Bmw you may need a Interface 16 pin Adapter, depending on the code reader.

Here is a home user code reader : PocketScan™ OBD II Code Reader (AXRCP9125 ...

Here is a good scaner.

Always better having the job done at a qualified garage.

Posted on Oct 24, 2008

  • 840 Answers

SOURCE: 1998 BMW 328i Rear WIndows broken

then it is the actual buttons for the windows on the rear doors

Posted on Apr 12, 2009

  • 60 Answers

SOURCE: how to change Front Turn Signal Light Bulb in 99 BMW 328i

if it is a e36 model just slid a ruller or somethig simuller between the light and flasher unit and it should slide forwerds

Posted on May 05, 2009

  • 490 Answers

SOURCE: 2000 BMW 328i yellow oil light on but oil is fine

Your sensor is going bad or you have to change your oil.

Posted on Jul 29, 2009

ZJLimited
  • 17970 Answers

SOURCE: BMW 328i Starter how to replaice

1999 BMW 328I 2.8L EFI DOHC 6cyl

Starter - Removal & Installation

The starter motor on some models is very difficult to see from the top of engine compartment as it is covered by the intake manifold. On these models, without removing the intake manifold, the starter motor must be removed from underneath the vehicle. Because the starter motor mounting bolts are not easy to access, a long extension with a universal joint mounted on a proper sized socket could be used. A three foot transmission extension is commercially available from tool vendors that has a 3 / 8 inch drive of the driven end and 1 / 2 inch drive on the drive end. If used with a non-binding impact universal joint and a proper fitting impact socket, the starter motor fasteners can be removed from underneath the vehicle.
Once the starter motor fasteners are removed, the starter motor may have to be moved side-to-side several times to loosen the dowel pin if it has corroded in place.

NOTE When the battery is disconnected, the radio code, on-board computer and clock settings will be lost. The radio code should be obtained before disconnecting the battery or radio. Once the battery has been reconnected, the radio will not function unless the code is keyed in.
Starter motor electrical terminal fastener torque specifications for all models:
M5 terminal fasteners: 44 inch lbs. (5 Nm)
M6 terminal fasteners: 53 inch lbs. (6 Nm)
M8 terminal fasteners: 115 inch lbs. (13 Nm)
Starter motor mounting fasteners:
Hex head bolts: 36 ft. lbs. (49 Nm)
Torx bolts: 32 ft. lbs. (43 Nm) Starter motor electrical terminal fastener torque specifications for all models:
M5 terminal fasteners: 44 inch lbs. (5 Nm)
M6 terminal fasteners: 53 inch lbs. (6 Nm)
M8 terminal fasteners: 115 inch lbs. (13 Nm) Starter motor mounting fasteners:
Hex head bolts: 36 ft. lbs. (49 Nm)
Torx bolts: 32 ft. lbs. (43 Nm) E36 6-Cylinder Engines
Automatic Transmission Models

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Set the ignition switch to the OFF position.
  3. Disconnect the negative battery cable.
  4. Remove the climate control air intake duct at the rear of the engine compartment as follows:
    1. Release the grille clips at the rear and lift the grille upward from the rubber seal, then remove the seal.
    2. Remove the two self tapping Phillips screws from inside the duct to release the electrical harness housing.
    3. Press the electrical housing downward to expose and remove the two hex head self tapping screws on each side of the duct and lift the duct up and out of the engine compartment.
  5. Remove the intake manifold trim and valve cover trim covers.
  6. Disconnect the ignition coil electrical connectors and ground straps, label for reinstallation and place aside.
  7. Remove the two fasteners that secure the fuel injection electrical connector harness to the rail. Remove the harness and carefully place aside toward the back of the engine compartment behind the right side strut tower.
  8. Remove the intake manifold.
  9. Remove the electrical leads from the starter motor and place aside.
  10. Remove the starter motor mounting fasteners at the transmission bell housing, then remove the two mounting nuts at the L-shaped mounting bracket.
  11. Loosen the L-shaped bracket to engine block mounting bolt slightly, then remove the bolt while supporting the starter motor.
  12. Remove the bracket, then lift the starter motor upward away from the engine.
  13. Visually inspect the starter pinion and ring gears for any signs of damage.
  14. Installation is in reverse order of removal.
Manual Transmission Models
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Set the ignition switch to the OFF position.
  3. Disconnect the negative battery cable.
  4. Raise and safely support the vehicle.
  5. Remove the fasteners for the reinforcement mounted between the frame rails just behind the rear lower control arm bushing brackets. Mark the bar-s direction for proper reinstallation and remove the bar.
  6. Remove the fuel line cover located near the left side rear lower control arm bushing bracket.
  7. Release the fuel lines and reverse light wiring from their routing brackets.
  8. Note the routing of the starter motor electrical wires, remove the wire mounting nuts, and place the wires aside.
  9. Remove the top and bottom starter motor to engine-transmission mounting fasteners.
  10. Remove the two mounting nuts at the L-shaped mounting bracket.
  11. Loosen the L-shaped bracket to engine block mounting bolt slightly, then remove the bolt while supporting the starter motor.
  12. Remove the bracket and carefully lower the starter motor downward away from the engine.
  13. Visually inspect the starter pinion and ring gears for any signs of damage.
  14. Installation is in reverse order of removal.

Fig. A view of the starter motor mounting fasteners and dowel pin. The mounting bolts are threaded into the starter motor

cd45991.jpg

Fig. The starter motor mounting bolts are a different size than the transmission-to-engine mounting bolts

2cbfa11.jpg

I hope help you with this (rated this help) Good luck.

Posted on Sep 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why my BMW is having all this dash, airconditioning and front headlightlots of Eletrical problems?


These cars have a LKM light control module know for failure. Tons of relays and brain boxes also common failures. You need a BMW expert, and maybe someone here knows more.

Apr 23, 2015 | 2000 BMW 328i

2 Answers

My 2009 BMW 328i has a light on that represents exterior lighting failure, but it seems that all the lights are working properly, how do I turn off this light?


It may actually be the case that one of your rear brake lights is out and you haven't noticed it; it's a subtle difference on the 2009 328i. Compare the brake lights in the photo attached. 2_24_2013_11_29_14_pm.pngI'd check for this before disconnecting the battery or taking it to the dealer.

Nov 04, 2012 | Cars & Trucks

1 Answer

2007 bmw 328i water pump problem


If it has an electric pump you should hear or see water flowing when car is turned on. If not, check any fuses or relays for the pump, and there is probably temp sensor controlling the pump. The main thing is to make sure any fuses and relays are working before tearing the pump out.

Sep 01, 2017 | 2007 BMW 328i Sedan

1 Answer

Would a lose serpentine belt cause wierd electrical issues inside car? Its a 1999 328i bmw (e46) the inside indicator lights not working, remote key stopped working


not real likely unless battery is goin dead and alt.is bad.Chech the small ground cable attached close to battery on the frame.i have had this problem recently and seen it happen alot.its a small black wire and usually their are sometimes other grounds to body at rear of engine.any of these can make guages act up then stop and headlights go out or all lights and speedometer stop.all kinds of weird things,dim interior light,dash light so on,hope you fet it.

May 25, 2012 | 2000 BMW 328i

1 Answer

2000 328i BMW DSC light


DSC light only comes on.

May 10, 2012 | 2000 BMW 328i

1 Answer

2000 BMW 328i yellow oil light on but oil is fine


Your sensor is going bad or you have to change your oil.

Jul 29, 2009 | 1998 BMW 3 Series

1 Answer

Maintenance due light is on


Service interval indicator can only be reset using a suitable diagnostic tool.

Sorry!

Apr 29, 2009 | 2000 BMW 3 Series

3 Answers

How to change Front Turn Signal Light Bulb in 99 BMW 328i? How do I release the housing?


if it is a e36 model just slid a ruller or somethig simuller between the light and flasher unit and it should slide forwerds

Apr 27, 2009 | BMW 328 Cars & Trucks

1 Answer

Indicator light for a 1997 bmw 328i


i think it means that you have a turn signal bulb that needs replacing cause its not working. check turn signals and see if they are blinking properly from front & rear of vehicle.

Mar 16, 2009 | 1997 BMW 3 Series

Not finding what you are looking for?
2007 BMW X3 3.0si SAV Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...