Question about Cars & Trucks

Open Question

Rear bumper senser not working right - Cars & Trucks

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I recently had my rear bumper pulled off my car after replacing it my rear sensors in bumper no longer work


If you took it off, check the wires on the sensors. IF someone worked on it and charged for it, make them fix it. Make sure it is the right bumper and the sensors were not damaged.

Feb 05, 2016 | 2011 Lincoln MKS

1 Answer

We are replaced engine for 2000 Audi A6 Quattro, check eng was "on", we are replaced Oxigen Sencor and Mass Air Flow Senser, everything was fine, eng, works good, then car seating a while and appeare


p1423 p1411
u either forgot to put the hoses at the air motor or air motor not working.the location is at the passenger side in front of engine behind bumper and right beside the a/c dryier.looks like a blower....
p1227 can not remember......
check light went on when the engine got warm?

Sep 19, 2014 | 2000 Audi A6

1 Answer

How to remove rear bumper for my 95 honda accord


Under the rear wheel wells, along the edge near the back is a screw. There is one on mine but there be more than one. Remove the screws for each.

After this, pop the rear trunk and look along the edge of the trunk right where the trunk hood meets the trunk itself. There are three black plastic screws that hold the rest of the rear bumper to the frame. I don't know exactly how these screws work but they don't just unscrew - I had to pop them out with a screw driver instead of rotating them out. Once those are out the rear bumper will lift up and off. There are some hooks along the rear wheel well where you removed the screws - you need to lift and pull out these edges, then lift the entire rear bumper off from the middle of the rear bumper.

Once you've done this, it goes pretty easily. If you have no problem with removing the black plastic screws or unhooking the edges, it should come off in less than five minutes.



Read more: http://wiki.answers.com/Q/How_do_you_remove_1996_Honda_Accord_rear_bumper#ixzz1Azw2wVAN

Jan 14, 2011 | 1995 Honda Accord

1 Answer

Speed sensor failed. can i replace it


Sure you can if a mechanic can do it so can you if you have the right tools and knowlege. First you need to know which one thers's one at each whell at the fround rear end housingf the rear rear end housing and the one in the side of the transfer case where the speedometer cable would'of connected on an older model and then theors three in the sides of the trans mission, Touque converter speed forward turbine speed output turbine speed. What proble are you trying to fix? the speedometer not working? Abs light on? Cheack engine light on? Cruise control not working? If the cruise control does work the speed senser is good and the check engine light will be on if the speed senser is'nt working. If the speed senser is'nt working the car will only take off in low and not shift to seecond or any higher gear as the computer doesn't know how fast the car is going. If the speedometer is'nt working and it does shift and cruise and the check engine light is'nt on then the speed senser is working but the speedometer is'nt if it is'nt and everything else is woring then as your driving hit the speedometer with your fist and see if it comes back on they can get stuck and i've fixed quite a few and they stayed fixed. On to wheel drive models with the rear wheels jacked off the ground safty I've run the car up to speed and trying wiggleing the wires and connectors till I wiggled the right thing till the speedometer came on ( including smacking the speedometer ) Just don't hit it too hard as it'll bust just like anything else.

Dec 21, 2010 | 2005 Jeep Liberty

2 Answers

How do you remove a rear bumper


How To Install Replace Remove Rear Bumper Cover Honda Civic 01-05

Dec 11, 2010 | 2004 Honda Civic

1 Answer

My 2009 Corolloa LE was bumped in a parking lot by a yellow truck, on the right rear bulge of the bumper, leaving a ding in the bumper. I can only partially access the backside of the bump by removing the...


Go underneath with socket and wrench. there will be 2 bolts with nuts on one end and two on the other end. Then the entire bumper can then pull off.

Nov 15, 2009 | 2009 Toyota Corolla

1 Answer

97 jimmy wont start


If it starts with starting fluid, this means the firing and electrical is fine,however, its not getting fuel. I suggest trying the fuel filter first,but, its probably going to be the fuel pump.

Dec 29, 2008 | 1997 GMC Jimmy

1 Answer

Rear Bumper Cover


you would need to heat it up from behind to remove the dent and the rubbing compound should work as long as it hasnt penetrated your paint layer

Jun 07, 2008 | 2001 Ford Taurus

1 Answer

Dented right rear bumper


If it isn't hurt too bad, put a heat light or heat gun to it for a few minutes, it might pop back out or if you can get up behind the damage, work it out with your hand while it is warm, wear gloves in case you get it too warm. About $650.00 painted and installed.

May 15, 2008 | 2007 Saturn Aura XR Sedan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

10 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...