Question about 1999 Ford Taurus

Open Question

How do you replace harmonic balancer on 99 ford taurus 24v 3.0

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: HARMONIC BALANCER

I have a '94 Tempo, it had a "ticking" sound. It was the "harmonic balancer" (crankshaft pulley) a local mechanic changed it for $60, the part cost me $120 (I work for a Ford dealership) $180 without employee discount. you can get one for much less at a junkyard if you can find one. Good luck, Sean

Posted on May 14, 2009

Ad
csmock132
  • 4669 Answers

SOURCE: 99 ford taurus is running hot. No water leaks,

OHV engine. I have seen these wear the blades off the waterpump. Does the heat work.

Posted on Jun 28, 2009

  • 62 Answers

SOURCE: replacing the harmonic balancer in ford bronco

First remove radiator fan shrould.This will give you access to the fan.Remove fan and fan belts.Remove bolt on harmonic balancer.You will need to rent a balancer remover and installer kit.Most big auto parts chains will rent these kits to you.Next remove four bolts holding pulley to balancer.Next attach balancer puller to balancer with long bolts from kit.Using a 1\2 drive breaker bar,remove balancer from engine.After removing balancer replace front seal.Lubricate hub on new balancer with engine oil.Then use installation tool from kit to install balancer.Never try to beat balancer on with hammer,engine damage could occur.Then work in reverse to replace remaining parts.Hope this will help you.

Posted on Aug 06, 2009

  • 21 Answers

SOURCE: 1998 ford Taurus 24v DOHC Overheating not thermostat

check to see if eans coming on if they dont then its fan relay if they are the rad is pluged or ther is an air pocket in the cooling system there should be a bleeder on it

Posted on Oct 06, 2009

  • 480 Answers

SOURCE: 1999 Ford Taurus 3.0L V6 24V DOHC Duratec Engine

i would check the plug wires and the coils you check the plug wires for bad spots at night start the motor up and look at the plugs if you see a spark arch out the wire and to a peace of metal then the plug wires need to be replace.

Posted on Dec 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i get printable instructions on removal of engine on 1996 Taurus lx 3.0 trying to replace c.s. pulley and harmonic balancer.?


if you support the engine sub frame at the pulley end then unbolt it you can raise the car. by doing this the motor will lower and It should be enough to give you enough clearance to remove the pulley and balancer.

Aug 21, 2014 | 1996 Ford Taurus

1 Answer

99 Mercury Marquis Harmonic Balancer pulled out


Replace balancer...rubber is bad...seperating.

Sep 02, 2012 | Mercury Cars & Trucks

1 Answer

The Serpentine belt keeps walking off the Crank shaft pulley by one rib as if the pulley moved away from the engine.. Is this where the harmonic balancer is. If so, is it difficult to change?


Before you change anything,,check and see if everything is in line..Also feel all the pulleys and make sure everything turns ok...If the powersteering pump has been replaced,,sometimes the pulley was not pressed on far enough..If it seem to be the harmonic balancer make sure its not damage and the bolt in the middle is tight...If you remove it..You remove middle bolt,,then you have to use a puller to remove the harmonic balancer itself..unusuall for the harmonic balancer to be bad unless it was hit by something

Sep 20, 2011 | 2005 Ford Taurus

2 Answers

How do you replace the front crankshaft seal on a 2000 ford taurus without pulling the engine?


NEED TO REMOVE THERADIATOR THE FAN SHROUD AND FAN FREMOVE THE FAN ASSEMBLY, REMOVE THE HARMONIC BALANCER IN OREDER TO GET TO THE SEAL

Aug 08, 2011 | 2000 Ford Taurus

1 Answer

1999 Ford Taurus. Can see crankshaft spinning fine coming out of block. Nut on end holding harmonic balanced spinning fine too. Harmonic balancer doesn't spin. How to fix? Do I need to pull the engine to...


There is a key way in the crankshaft and the balancer with a woodruff key that keeps it locked in place. The woodruff key resembles a half moon shape. You will have to remove the balancer to see what kind of damage there is and go from there.

Jan 02, 2011 | Ford Taurus Cars & Trucks

1 Answer

Im trying to find the location of the crank shaft position sensor for a 2002 ford taurus. Im wanting to replace it myslef.


Hi you will find the crank shaft sensor on the passenger side of the engine on the back side right behind the harmonic balancer.
If you remove the front tire and the plastic splash shield you will be able to locate it easier. Hope this helped happy motoring

Aug 26, 2010 | 2002 Ford Taurus

2 Answers

I am unable to remove the crankshaft pulley on my 1999 ford taurus


the crankshaft pulley is also called the harmonic balancer.At any parts house checker,autozone,ect. will have the tool you need.It is called a harmonic balancer puller and bolts to the pulley and pulls it off.Let me know if this helped.

Jan 09, 2010 | 1999 Ford Taurus

2 Answers

2001 Ford Taurus, Harmonic balancer removal


I had this problem and had to block the teeth of the harmonic balancer with a 2-ton hydraulic jack handle (use an assistant to hold) while I torqued on the bolt with a 4-way lug wrench and a length of pipe. Took a minute, but finally we heard the "ping" of the seal breaking and were able to remove that BAB.

Aug 03, 2008 | 2001 Ford Taurus

1 Answer

1990 ford taurus


front of engine, between the harmonic balancer and the water pump

Jul 20, 2008 | 1990 Ford Taurus

Not finding what you are looking for?
1999 Ford Taurus Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

fordexpert

Level 3 Expert

5581 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...