Question about Cars & Trucks
Posted by Anonymous on
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
These codes are all for the Evaporative Emissions System.
P0440- Evaporative emissions system fault- just saying there's something wrong with the system.
P0441- Evaporative emissions system- Incorrect purge flow- saying that the system isn't purging the raw fuel vapors (hydrocarbons- HC) as well as it should.
P0446- Evaporative emissions system- Control valve circuit low- there is a valve, usually located on the charcoal canister at the rear of the vehicle, that opens to allow fresh air to enter the evaporative emissions system as the engine vacuum purges the fuel vapors from the charcoal canister and closes when purge is not needed to prevent leakage of those fuel vapors to the atmosphere (HC is a greenhouse gas and is regulated as such by the fed gov't).
Given that you have the incorrect purge flow code and the control valve code together, my bet is that the vent control valve has failed (causing the P0446) and is not opening to allow fresh air into the system to displace the air from within the system that is being pulled to the engine. Since you have no fresh air entering the system, the engine will pull a vacuum on the system instead of the vapors "flowing" into the engine (causing the P0441).
I hope that this is helpful to you!!!
ASE Master Technician with L1 and X1 Certifications; Nissan Scope Technician; Chrysler Level 3 Silver Technician- 12+ years experience.
Posted on Nov 17, 2008
SOURCE: 1998 toyota camry V6
P0420 indicates you have a catalyst efficiency issue; replacement of the Air-Fuel Sensor should take care of that;
The P0441, P0446 and (I assume P0440); you said 446 twice, indicates a faulty or loose fuel cap; it is not sealing properly.
Please feel free to respond to me if you have any further questions.
A FixYa rating from you regarding my assistance would be greatly appreciated.
Posted on Dec 27, 2008
Diagram is unnecessry.
Pull both front wheels
Work one at a time leaving the other for reference
Find the retention spring ... its a paperclip thickness wire spring... dislodge center retention loop and undo from both ends which engage brake pad retention rods.
Pull the rods out
Pull the old pads out... laying everything on the ground
Use scrap wooden wedges to pry between the rotor and the caliper ...inside and out until the calipers are fully withdrawn. Use the new pads to measure if they are far enough back.
Note... the brake fluid will have dropped in the master cylinder over many months of wear... do not fill it. When the calipers are pushed back they will fill the reservoir again... one wheel at a time.
Be sure to identify the correct pad based on what you took out and what is on the other side (if you screwed up the layout)
Make sure to take the old antisqueek backing plate from the old pad and place it on the new pad. They don't use lubricant on these anymore.
Replace the pads... the retention rods... then the retention spring
Do the other side
Then progressively step on the brake peddle until full tension is felt
Check the master cylinder reservoir... probably needs no additional fluid.
New pads will register in existing ridges in each disc in no time at all.
You should check the discs to see if they need to be replaced during this operation...using some calipers
Posted on Mar 25, 2009
Both codes are with the EVAP SYSTEM, there are numerous items it could be. A repair shop that does Toyotas or the delaler would be the best to check it out for you. Its not anything that will leave you walking or disable the car.
Posted on Nov 13, 2009
Tips for a great answer:
May 20, 2011 | 2000 Toyota Camry
Nov 13, 2009 | 1998 Toyota Corolla
Sep 24, 2009 | 1999 Toyota Camry
Jun 26, 2009 | 2002 Toyota 4Runner
Apr 28, 2009 | 2000 Toyota 4Runner
Apr 13, 2009 | 1999 Toyota 4Runner
Mar 08, 2009 | 1998 Toyota Camry
Dec 27, 2008 | 1998 Toyota Camry
25 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: