Question about Cars & Trucks

Open Question

97AP-15607-AB WIRE DIAGRAM - Cars & Trucks

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
edwardjwoods
  • 372 Answers

SOURCE: how to install a pats system

that has to be programed by the dealer after its installed or you will lock the theft system and not be able to run the car

Posted on Apr 18, 2012

Ad
edwardjwoods
  • 372 Answers

SOURCE: HOW TO INSTALL A PATS XCVR 97AP-15607-AB [USBTE939] [CEP-LPD

take it to the dealer. its a big pain in the **** as it has to be programmed and only ones who can do that is ford.

Posted on Apr 18, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wire in a Ford PATS Transceiver F8SB-15607-AC Ignition Lock Cylinder and Key FOB Explorer


i've found a few references on how to by pass this but if you follow this link to the ford explorer forum you will get better info and advice from fellow explorer owners/mechanics who know the vehicle from top to bottom
2002 ford PATS transceiver XLT won start

May 21, 2014 | 1999 Ford Explorer

1 Answer

Airbag light reset code


You would need to reset the warning light and then see if it comes back on, which would indicate a fault still there. Try this procedure

http://s16.photobucket.com/user/rogersb/media/AirBagReset.jpg.html

"How do you reset the airbag warning light in a '94 Camry?
A: Clearing the warning light in '92-'96 Camrys by the following procedure:
In the DLC1 or DCL2 (data link connector under the hood, see following diagram)
Use two short wires, one wire at terminal TC and a different wire at terminal AB
With the ignition key ON - wait 6 seconds, then:
Ground terminal TC to good body ground for one second
Then ground terminal AB for one second
Then TC one second
Then AB one second
Then ground TC until the light blinks.
Make sure the interval between grounding terminals is not more than 0.2 sec.
Remove the ground wires
Be very careful to only use the correct terminals."

Jan 21, 2014 | Toyota Cars & Trucks

1 Answer

Airbag light on


Try this procedure, but if it comes back on, your airbag is faulty, of course.
A: Clear the warning light in '92-'96 Camrys by the following procedure:
In the DLC1 or DCL2 (data link connector under the hood, see following diagram)
Use two short wires, one wire at terminal TC and a different wire at terminal AB
With the ignition key ON - wait 6 seconds, then:
Ground terminal TC to good body ground for one second
Then ground terminal AB for one second
Then TC one second
Then AB one second
Then ground TC until the light blinks.
Make sure the interval between grounding terminals is not more than 0.2 sec.
Remove the ground wires
Be very careful to only use the correct terminals.
cc08c9a7-2326-431d-84b4-ab8f01d33743.jpg

Jun 23, 2013 | 1993 Toyota Camry V6

2 Answers

Air bag reset 1995 toyota camry


I haven't had to try this but here is a procedure for resetting the airbag after the battery was disconnected


"How do you reset the airbag warning light in a '94 Camry?


A: Clearing the warning light in '92-'96 Camrys by the following procedure:
In the DLC1 or DCL2 (data link connector under the hood, see attached diagram):
Use two short wires, one wire at terminal TC and a different wire at terminal AB:
With the ignition key ON - wait 6 seconds, then:
Ground terminal TC to good body ground for one second
Then ground terminal AB for one second
Then TC one second
Then AB one second
Then ground TC until the light blinks.
Make sure the interval between grounding the terminals is not more than 2 secs.
Remove the ground wires.




Be very careful to only use the correct terminals.
8_11_2012_5_40_39_am.jpg

Aug 05, 2012 | 1995 Toyota Camry

1 Answer

HOW TO INSTALL A PATS XCVR 97AP-15607-AB [USBTE939] [CEP-LPD


take it to the dealer. its a big pain in the **** as it has to be programmed and only ones who can do that is ford.

Apr 18, 2012 | 2000 Ford Escort

1 Answer

How to install a pats system


that has to be programed by the dealer after its installed or you will lock the theft system and not be able to run the car

Apr 18, 2012 | Ford Cars & Trucks

1 Answer

Lambda oxy sensor def. Will Denso work


Yes, the Denso Mfr #: 234-4209 O2 sensor is a universal 4 wire pre cat sensor that will work in your vehicle. Bosch also makes an exact fit sensor, #15606 for the upstream & 15607 for downstream.

Jun 28, 2011 | 2004 Mitsubishi Outlander

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...