Question about 1999 Lincoln Navigator

Open Question

Remove cruise control switch - 1999 Lincoln Navigator

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the signal light relay that makes signal lights flash located on 2000 ols intrigue 3.5 liter


Important: The hazard warning switch includes the turn signal and hazard warning flashers.
Removal Procedure
Remove the center air deflector. Refer to Instrument Panel Center Air Outlet Deflector Replacement .
Squeeze the retainer on the backside of hazard warning and cruise control switch.
Pull the hazard warning and cruise control switch from the retainer in the instrument panel.
Disconnect the electrical connectors from the hazard warning and cruise control switch.
Remove the hazard warning and cruise control switch from instrument panel.
Remove the hazard warning and cruise control switch bezel from the instrument panel trim pad by using a small flat-bladed tool to the release retainers.
Remove the radio. Refer to Radio Replacement in Entertainment.
Reach through the radio opening and push the retainers up towards the roof of the vehicle. When the retainers release, slide the instrument panel (I/P) center air outlet deflector out of the I/P opening
Remove the air outlet deflector
Remove the instrument panel accessory trim plate. Refer to Instrument Panel Accessory Trim Plate Replacement in Instrument Panel, Gauges, and Console.
Remove the bolts from the radio.
Pull the radio toward you.
Remove the front floor console trim plate. Refer to Front Floor Console Trim Plate Replacement .
Pull the instrument panel (IP) accessory trim plate away from the IP trim pad.
Disconnect the IP harness seat heater leads, if equipped.
Remove the seat heater switches from the IP accessory trim plate, if equipped.
Remove the IP accessory trim plate.

Nov 09, 2016 | Cars & Trucks

1 Answer

98 manual vw passat cruise control not working any ideas to start and find the problem


Apr 08, 2014 | 1998 Volkswagen Passat

1 Answer

98 manual Vw passat cruise control is not working any help on where to start to find the problem


Apr 08, 2014 | Cars & Trucks

1 Answer

How do I fix my cruise control


first ck fuse for cruise control,if ok ck power to main switch use a omp, amp meter for test, should have battery voltage to and from switch when in on position. if ok your next ck is steering wheel switch. air bag must be removed unhook battery wait five minutes remove airbag hook battery up ck steering wheel switch if ok below steering wheel is cable reel ck yellow connectors on both side for power if all have power to and from go under hood and ck power to cruise unit if ok pcm may not be letting it come on because of engine or trans readings dtcs pending or set can shut off cruise control

Jul 14, 2012 | 2007 Jeep Compass Limited

2 Answers

How to fix cruise control


Cruise controls can cease to engage if the clutch or brake light cruise switch are out of adjustment. If this happens, try placing you foot under the clutch pedal (if equipped) and lift up on it (toward you) and hold it while engaging the cruise. If it now works, it will likely cut out when you remove your foot from under the pedal. Check the brake pedal in an identical fashion. Adjusting the switch at the pedals can often solve he problem. Some vehicles (Honda, Acura, Ford, to name a few) have a plastic insert that mounts in the pedal arm which presses against the switch. These can become brittle and fracture into pieces. My Acura has little pieces of blue plastic on the floorboard around the brake pedal one afternoon and I noticed the cruise didn't work. It was the pieces of the insert that had come to pieces preventing the cruise from coming on. I replaced the insert and no more problem with the cruise.

Mar 10, 2012 | 2003 GMC Sierra 2500HD

1 Answer

My cruise control light behind the button is burnt out how do I get at it to replace it.


The following is from 2002 Honda Odyssey factory manual page 20-70: Driver's switch panel removal. (This is the switch panel to the left of the steering wheel with TCS, cruise control, mirror, and sliding door switches.) Gently pull on the driver's switch panel bottom right corner to release the (2) right side clips, then detach the remaining (2) clips on the left side and the single top center clip. If equipped, disconnect the cruise control main switch connector, TCS switch connector, power mirror switch connector, and power sliding door connector, then remove the panel. Once the panel is removed, you can push out the switch from the rear. The switch has two bulbs in it, one is the cruise switch backlight bulb and the other is the cruise control function bulb.

Jan 13, 2011 | 2002 Honda Odyssey

1 Answer

How do i replace the cruise control on/off switch on my 1999 alero


TO REMOVE CRUISE CONTROL SWITCH. FIRST TURN OFF RADIO TO KEEP FROM LOSING CODE. DISARM AIRBAG IN THE STEERING WHEEL BY REMOVING NEGATIVE BATTERY CABLE WAIT 20 MINUTES FOR AIRBAG TO DISCHARGE BEFORE REMOVING AIRBAG AND HORN PAD IN STEERING WHEEL.ONCE AIRBAG IN STEERING WHEEL OUT.YOU CAN REMOVE THE CRUISE CONTROL SWITCH.BECAREFUL REMOVING AIRBAG IN STEERING WHEEL CARRY IT AWAY FROM BODY WITH AIRBAG HORN PAD POINTING UP.IF YOU DROP IT.DONT PUT IN BACK IN STEERING COULD DEPLOY ON INSTALLATION.

Nov 14, 2010 | 1999 Oldsmobile Alero

2 Answers

I own a 2005 GMC Canyon Five CYL and the cruise control stopped working last niight. You push the button and no cruise. I checked the fuse and it is ok I exchanged with another 10AMP and no change still...


Start with the simple and check the fuses and the Stop lamp switch. Check your brake lights, if they're not working, the cruise won't work either. If they're not working, check the fuse for them, if the fuse is fine, then take it into the dealer, there's been a recall issued on the brake switch, so it should get fixed for free.
Cruise Control Disengaged
The powertrain control module (PCM) disengages the cruise control operation based on the signals from the following switches:

* The stop lamp switch
* The TCC brake/cruise release switch
* The clutch release switch, if equipped
* The cruise control On/Off switch

The TCC brake/cruise release switch and the stop lamp switch are mounted on the brake pedal bracket. When the brake pedal is applied, the normally closed TCC brake/cruise release switch opens and the normally open stop lamp switch closes. The PCM detects a low signal voltage on the TCC brake/cruise release switch signal circuit and a high signal voltage on the stop lamp switch signal circuit. When the clutch pedal is applied, the normally closed clutch release switch opens and the PCM detects zero voltage on the CCP switch signal circuit. The vehicle speed stored in the memory of the PCM will be erased when the cruise control On/Off button is turned OFF, or the ignition switch is turned OFF.

The Cruise Control System will disengage when the PCM detects that a driver override function has been active for approximately 60 seconds .

When the Cruise Control System is disengaged, the PCM sends a class 2 message to the instrument panel cluster (IPC) in order to deactivate the cruise control indicator.

Cruise Control Inhibited
The powertrain control module (PCM) inhibits the cruise control operation when any of the following conditions exist:

* A cruise control related DTC has been set.
* The vehicle speed is less than 40.2 km/h (25 mph) .
* The vehicle is in PARK, REVERSE, NEUTRAL, or 1st gear.
* The engine RPM is too low.
* The engine RPM is too high, with fuel cut off.
* The vehicle speed is too high, with fuel cut off.
* The system voltage is not between 9 volts and 16 volts .
* The Traction Control System (TCS) is active for more than 2 seconds .

Thank you for using Fixya and start with replacing the stop lamp switch. Even though the brake light work, it;s been known for that switch to cause your issue. that's way there was a recall for it.

Apr 01, 2010 | 2005 GMC Canyon

1 Answer

HI, I have a 1988 Ford Ranger, V-6, 2.9L. I've had problems with the engine stalling on an intermittent basis. The first time it happened was when I switched on the cruise but it has happened since with or...


I solved this problem so I'm posting this to help others. I was getting a code indicating a problem with the BOO switch (brake on/off). C the switch which is located on the brake pedal and continued to have a code 74. I found out that the cruise control has a redundant brake on/off switch at the end of the cruise control vacuum hose which is also located near the top of the brake pedal. I disconnected and plugged the vacuum hose leading to this switch and removed the cruise control from the engine compartment. This solved the trouble code problem although I don't have cruise anymore.

Mar 26, 2010 | 1988 Ford Ranger

2 Answers

I need to repace the cruise control switch how do I get the horn cover off


1. Remove the lower steering column cover.
2. Remove the AIR BAG bolts from the back side of the steering wheel with a T-30 socket. Install the bolts back in the air bag for reassembly. The AIR BAG will snap into place when pushed down on carefully.
3. Remove 2 screws on the bottom of the steering wheel cover. The wires need to slide out so the switch can be removed.
4. Remove the cruise control switches.

The AIR BAG does not have to be disconnected to remove the switches, just don't let it flop around or stretch the wires.

Dec 25, 2009 | 2000 Oldsmobile Alero

Not finding what you are looking for?
1999 Lincoln Navigator Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

fordexpert

Level 3 Expert

5474 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...