Question about 2001 Mazda MPV

Open Question

Brake bleeding order for a 1999 mazda mpv - 2001 Mazda MPV

Posted by Anonymous on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 51 Answers

SOURCE: need cylinder firing order for mazda mpv 2004

Firing order is 1-4-2-5-3-6. Also the front three cylinder from driver's side to passenger are 6 5 4 and the rear are 3-2-1

Posted on Oct 08, 2008

  • 1 Answer

SOURCE: 2004 mazda mvp firing order

The firing order is 1-4-2-5-3-6. The cylinders are, front bank is from drivers side to passenger, 6-5-4 , and 3-2-1 at the firewall. This is for a 2004 Mazda MPV.

Posted on Dec 03, 2008

  • 460 Answers

SOURCE: bleeding brake on a 2002 mazda protege 5

Start from the furthest away from the master cylinder and work your way forward..And make sure who is helping you bleed them they hold the brake to the floor and dont let up until you've tighten the bleeder screw..And make sure your master cylinder is full every time you bleed one tire so that you dont run out getting more air in the systems..Hope this helps you and Have A Great Day

Posted on Apr 05, 2009

  • 80 Answers

SOURCE: 2002 mazda mpv firing order please

let me know if this help you....


Posted on Oct 04, 2009

Testimonial: "tank you that was very helpfull because i call to mazda and they tell me the coil number 5 was in the midle on back "

  • 701 Answers

SOURCE: firing order

Hello vtarin1: My name is Roger and I will help you. The fire order on the motor is 1-4-2-5-3-6. I will send a picture also. Should you need further help please just ask. Please rat the answer you received. Thank You for using Fix Ya. Roger3323b6b.jpg

Posted on Oct 28, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2000 Mazda M.P.V E.S 2.5 bleeding the coolant

I've owned my 2000 MPV since new and in that time and 250K miles later I have replaced the radiator and water pump and overflow tank. I have never bleed the cooling system. I have encountered no cooling related problem. I live in south Florida.

Dec 03, 2014 | 2000 Mazda MPV

1 Answer

Why my front brakes are overheating after I replaced/serviced the rear brakes pads ?

try bleeding the front brakes sometimes the valve will move to one side allowing more pressure to the opposite brake possibly causing this type of problem.

Aug 22, 2014 | 1989 Mazda MPV

1 Answer

2001 mazda mpv van brake light stays on after changing brakes and bleeding system how do you get the light to go off

check the master cylinder. there is a float in the reservoir that when the level gets low, it turns on the brake light. or check the ebrake...also on ABS systems you have to actuate the ABS module with a scantool to get out all the air in the system.

Nov 14, 2013 | 2001 Mazda MPV

1 Answer

I changed the brake and bleed the system and the brake light is on how can i get the light off

check brake fluid level first. there is a float in the master cylinder reservoir. when the level is low, it turns on, warning you about a potential issue.

Nov 14, 2013 | 1996 Chevrolet Tahoe

1 Answer

Steps to replace water pump mpv 3.0

Remove the battery and battery tray.
Drain the engine coolant.
Remove the water pump drive pulley.
Remove thermostat case
Remove water pump tensioner
Remove water Outlet pipe
Remove water pump
Reverse disassembly order to install water pump.
Fill and bleed cooling system

Aug 14, 2011 | 2004 Mazda MPV

1 Answer

The rear brakes seem unable to bleed. i think the proportioning valve bad.

You are correct in assuming the proportioning valve,but it may not be bad,if it detects,loss of fluid pressure,it will shut down those brake lines.Try bleeding the master cylinder,then the wheels,and you may have to do it a couple of times,this will allow the proportioning valve allow the wheels with fluid pressure,if this was at all helpful,please rate,thank you,

Jun 27, 2010 | 1992 Mazda MPV

1 Answer

No brake pressure on my 1991 mazda mpv, changed master cylinder and bleeded the brakes.

you have to remove the pipes that go out of the master cylinder and purge the air later you connect the pipes and it purges the air in every auxiliary cylinder and the pedal will begin to have pressure

Dec 13, 2009 | 1991 Mazda MPV

1 Answer

Trided everything why cant my brakes come on?

have you bleed them. (if you got air in the system this will definately be irritating to get rid off, takes a while to bleed if you did this )

Feb 05, 2009 | 1989 Mazda MPV

Not finding what you are looking for?
2001 Mazda MPV Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts


Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides