Question about 2008 Hummer H3

Open Question

SECONDARY AIR INJECTION HUMMER

COLD START miss FOR FEW seconds, when you hear air pump come on, clears up and runs smooth. bad chack valve?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
ancdlm
  • 58 Answers

SOURCE: I just installed new air bags for rear suspension

It sounds to me like your compressor got killed. What probably happened is that the airbag got a hole or tiny crack in it so the compressor has to work extra hard because it is like blowing up a balloon with a hole in it. Therefor the airbag killed the compressor. I would recommend going to strutmasters.com and taking a look at our conversion kits. these convert you from the airbag to a powder coated American made steel coil spring that is guaranteed to last the life of the car. I added the link below so you can check it out.
http://www.strutmasters.com/hummer-suspension-parts-s/96.htm I hope I was of some help
Good Luck!!!

Posted on May 06, 2009

Ad
soc21610k
  • 215 Answers

SOURCE: Cooling fan is not pushing air out.

That could be the blower motor resistor or the blower motor

Posted on Jun 04, 2009

  • 3 Answers

SOURCE: Hummer H3 air condition blower will not come on -

I just fixed this exact problem in my 06 H3. It turned out to be the resistor pack in the blower motor. I had to replace the resistor(it shorted) and the small harness that spiders over the blower motor assembly(it melted). It was an easy fix and only about $50 in parts that you can order form any GM brand dealership. Check out the link and and look at parts #3 and #4. Good luck!

Posted on Aug 03, 2009

  • 73 Answers

SOURCE: my 2004 hummer h2 blows hot air out of the drivers

one of your a/c door vacuum actuators is probobly bad.

Posted on Dec 12, 2009

  • 22 Answers

SOURCE: 2002 H1 Stalling and shuttering

Someytimes parts are faulty and that is what it may be.
Good Luck to you and God Bless you in this
finding out the problem and solving it for good

Posted on May 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2008 Trailblazer has OBD-II code P2430. How do I replace the secondary air injection pump?


This code doesn't mean to replace the air pump ,
DTC P2430 : Secondary Air Injection (AIR) System Pressure Sensor Circuit
Circuit/System Description
The secondary air injection (AIR) system aids in the reduction of hydrocarbon emissions during a cold start. The system forces fresh filtered air into the exhaust stream in order to accelerate the catalyst operation. An electric air pump, the secondary AIR injection pump, provides filtered air on demand to the AIR control solenoid valve/pressure sensor assembly. The AIR control solenoid valve/pressure sensor assembly controls the flow of air from the AIR pump to the exhaust manifold. The AIR solenoid relay supplies the current needed to operate the AIR control solenoid valve/pressure sensor assembly. A pressure sensor is used to monitor the air flow from the AIR pump. The engine control module (ECM) supplies the internal pressure sensor with a 5-volt reference, an electrical ground, and a signal circuit.
This is a pressure sensor problem . What this video on testing !
Chevrolet Malibu P2432 Secondary Air Injection System

May 11, 2017 | Cars & Trucks

1 Answer

Is the secondary air injection system nessary for good engine performance or is it's function only to dilute burn exhaust emissions?


It's only used on cold start to help the Catalytic converter light off . The check engine light will be on all the time if you disconnect it .
The Secondary Air Injection (AIR) System aids in the reduction of hydrocarbon exhaust emissions during a cold start-up. This occurs when the start-up engine coolant temperature (ECT) is between 5-50°C (41-122°F), and the intake air temperature (IAT) is between 5-60°C (41-140°F). The AIR pump operates 5-60 seconds after start-up.
The powertrain control module (PCM) activates the AIR system by simultaneously supplying grounds to the AIR pump and the AIR valve relays. This action closes the relays' internal contacts. The AIR pump and the AIR control solenoid valve/pressure sensor assembly are in turn energized, the pump runs and the control/shut-off valve opens.
The AIR pump sends pressurized fresh air into the pipes/hoses through the open control/shut-off valve, and into the exhaust manifold. The extra air accelerates the catalyst operation, helping it to reach operating temperature faster. The AIR pump remains ON for a short period of time after the control/shut-off valve is commanded OFF. When the AIR pump is commanded OFF it will not run or be activated until the next vehicle start. When the AIR system is inactive, the closed AIR control/shut-off valve prevents air/exhaust flow in either direction.

Apr 30, 2017 | Cars & Trucks

2 Answers

2008 trail blazer 4.2 4x4 fan under the hood runs all the time. Why how to fix?


What fan ? Your vehicle doesn't electric cooling fans , has engine cooling fan and clutch driven by the crankshaft via the drive belt. Your probably taking about the
Secondary Air Injection System Description .
The secondary air injection (AIR) system aids in the reduction of hydrocarbon exhaust emissions during a cold start-up. This occurs when the start-up engine coolant temperature (ECT) is between 5-50?°C (41-122?°F), and the intake air temperature (IAT) is between 5-60?°C (41-140?°F). The AIR pump operates 5-60 seconds after start-up.
The engine control module (ECM) activates the AIR system by simultaneously supplying grounds to the AIR pump and the AIR valve relays. This action closes the relays' internal contacts. The AIR pump and the AIR control solenoid valve/pressure sensor assembly are in turn energized, the pump runs and the control/shut-off valve opens.
The AIR pump sends pressurized fresh air into the pipes/hoses through the open control/shut-off valve, and into the exhaust manifold. The extra air accelerates the catalyst operation, helping it to reach operating temperature faster. The AIR pump remains ON for a short period of time after the control/shut-off valve is commanded OFF. When the AIR pump is commanded OFF it will not run or be activated until the next vehicle start. When the AIR system is inactive, the closed AIR control/shut-off valve prevents air/exhaust flow in either direction.
In the under hood fuse box find AIR PUMP fuse # 64 60amp pull the fuse an see if the fan goes off . There are two relays secondary Air injection (AIR ) pump relay . The contacts may be stuck together .
In the under

Oct 05, 2016 | 2008 Chevrolet Trailblazer

1 Answer

Code 410


code po410 on a 2004 gmc envoy is that there is a problem with the secondary air injection system, you will need to check the fuse located in the engine compartment first, the next step is to start the truck cold and listen for the air pump to turn on for a few seconds, this will sound like a jet engine but not that loud, after it runs for 5 min and you dont hear it then you may have a bad pump which is located under the driverside on frame but if you hear the pump then you may have a bad valve, this valve is located on the exhaust manifold area and has a hose from the pump to valve, remove the hose and check for water, drain any water in the hose, also remove hose at pump and drain, the most common cause for this code is the valve is not opening and the air pump gets water inside and goes bad, thats the po410 code. a quick note; if fuse is blown look under truck near pump and check relay as it fills with water and blows fuse, if this is the case replace relay and blow water out of connector.good day.

Dec 06, 2011 | 2004 GMC Envoy

2 Answers

Obd code of p0411 on a 1999 ford mustang 3.8 v-6 what do I check to correct


That's s failure of the secondary air pump. It'll have to be changed. It's an emissions component meant to help with cold start emissions. It won't cause engine running trouble but at inspection time you'll fail for smog. Change it before then and you'll be fine.

May 16, 2010 | 1999 Ford Mustang Cobra

2 Answers

Car is choking out and dying. Reads P 0411 code. How do I know if its the motor or just the solenoid valve? How can I check to narrow down what actually is causing the problem? It's on a 2000 VW jetta VR6


16795/P0411/001041


if (window.showTocToggle) { var tocShowText = "show"; var tocHideText = "hide"; showTocToggle(); } 16795/P0411/001041 - Secondary Air Injection System: Incorrect Flow Detected Possible Symptoms
  • Malfunction Indicator Light (MIL) ON
Possible Causes
  • Fuel Pump Relay (J17) faulty
  • Hoses/Pipes to/between Components faulty/clogged
  • Secondary Air Injection Pump (V101) faulty
  • Secondary Air Injection Pump Relay (J299) faulty
  • Secondary Air Injection Solenoid Valve (N112) faulty
Possible Solutions
  • Check Fuel Pump Relay (J17)
  • Check Hoses/Pipes to/between Components
    • Check Secondary Air Injection Hoses/Pipes for Carbonization
  • Check Secondary Air Injection Pump (V101)
  • Check Secondary Air Injection Pump Relay (J299)
  • Check Secondary Air Injection Solenoid Valve (N112)

Apr 28, 2010 | 2000 Volkswagen Jetta TDI

2 Answers

1998 328i.. Got a 1421 and 1423 code...not sure where to start...


1997 BMW 328I 2.8L Customer Concern: MIL is on with trouble codes P1421 and P1423, for incorrect secondary airflow on both cylinder banks. Tests/Procedures: 1. Perform a functional test of the Air Injection Reaction (AIR) system. Tee a vacuum gauge into the vacuum hose attached to the diverter valve, located on the cylinder head towards the front of the engine.

2. Allow the vehicle to sit over night. Start the engine (cold) while monitoring the amount of vacuum on the gauge at startup. At temperatures from -10 to 40 degrees Celsius, there should be at least 17 inches of vacuum. At the same time, the AIR pump should run and pump a large volume of air into the exhaust. Potential Causes: A.I.R. Pump
Air Pump Relay
Restricted Cylinder Head
Diverter Valve
Tech Tips: These codes are related to a problem detected in the Secondary Air Injection system. Scan tools with BMW software include a feature to command the AIR pump on and off. The pattern failures for these codes are the AIR pumps due to leaks in the diverter valve and moisture or condensation in the AIR pump.

Possible fix but not all items. Just areas to look at:
Confirmed Fix - A.I.R. Pump - A.I.R. Diverter - A.I.R. Pump, Air Injection Reaction Diverter (AIRD) Valve - Air Injection Reaction Diverter (AIRD) Valve - Check Valve, Secondary Air Pump - Diverter Valve Vacuum Lines

Jul 04, 2009 | 1997 BMW 328

2 Answers

1996 saab 900-s


There's a black plastic valve below the battery that fails frequently on these cars. It has a vacuum line and 2 thumb-sized hoses going to it. A lot of times the valve will be broken in half and obviously bad. This will cause a secondary air injection code. Also the vacuum hose to it needs to be intact. Check this stuff first.

Oct 28, 2008 | 1996 Saab 900

1 Answer

Get diagnostic code of P0410


Secondary Air Intake System Fault code P0410 is set by a defective air injection pump, this pump is electric, on older cars it was called a "SMOG PUMP" and was belt driven by the engine. On cold start do you hear a hair dryer type noise from under the hood? if not the pump has failed, if you do the check valve is stuck closed, the only way to fix either issue is a new secondary air injection pump.

Aug 21, 2008 | Volvo XC70 Cars & Trucks

1 Answer

Vw passat 2000 1.8t front wheel drive


please rate me solved...thanks

DTC P0411/16795: SECONDARY AIR SYSTEM - INCORRECT FLOW DETECTED
Test Requirements
Ensure all fuses are okay, battery voltage is at least 11.5 volts, all electrical accessories are off, A/C is off.
Ensure engine is mechanically sound.
Test Procedure

NOTE
Secondary air system is activated by ECM and blows air into exhaust pipe
upstream of catalytic converter for 100 seconds during a cold start, 41-91°F (5-
33°C). Engine must be cold to perform following test procedure.

1. Ensure fuse and secondary fuse (secondary fuse is 40 amp and is located in fuse holder on top of battery)
are okay. Check hoses and components of Secondary Air Injection System, for damage, loose fit and
improper installation, check vacuum hoses for Secondary Air Injection System. Repair as necessary.
Erase DTC memory. Verify repair. If DTC does not reset, test is complete. Perform ECM relearn
procedure. See TEST DRIVE RELEARN PROCEDURE .
2. Remove engine cover. Disconnect pressure hose from Secondary Air Pump Motor (V101), by pressing
buttons on hose connector. See Fig. 33 . Using scan tool, check Secondary Air Pump Motor (V101) in
scan tool Output Diagnostic Test Mode (Secondary Air Pump Relay activation mode). See OUTPUT
DIAGNOSTIC TEST MODE .
3. Secondary Air Pump Motor (V101) should run in intervals and air should exit pump at hose connection.
If Secondary Air Pump Motor (V101) is okay, go to step 7 . If motor runs and no air exits secondary air
pump motor, replace faulty Secondary Air Pump Motor (V101). Erase DTC memory. Verify repair. Test
is complete. Perform ECM relearn procedure. See TEST DRIVE RELEARN PROCEDURE . If
secondary air pump motor does not run, go to next step.
4. Disconnect Secondary Air Pump Motor (V101) harness connector, install LED test light at secondary air
pump harness connector terminals. Turn ignition on. Using scan tool, activate Secondary Air Pump Motor
(V101) in scan tool Output Diagnostic Test Mode (Secondary Air Pump Relay activation mode). See
OUTPUT DIAGNOSTIC TEST MODE . LED test light at Secondary Air Pump Motor (V101) harness
connector should flash. If LED test light at Secondary Air Pump Motor (V101) harness connector does
not flash, go to next step. If LED test light at Secondary Air Pump Motor (V101) harness connector
flashes, replace faulty Secondary Air Pump Motor (V101). Erase DTC memory. Verify repair. Test is
complete. Perform ECM relearn procedure. See TEST DRIVE RELEARN PROCEDURE .
5. Using DVOM check resistance of Secondary Air Pump Motor (V101) wiring. See appropriate WIRING
DIAGRAM under ENGINE PERFORMANCE in SYSTEM WIRING DIAGRAMS. Resistance should
be a maximum of 1.5 ohms for each reading. Check wiring for short circuit to one another in Secondary
Air Pump Motor (N101) harness connector. Repair as necessary. Erase DTC memory. Verify repair. Test
is complete. Perform ECM relearn procedure.
Secondary Air Pump Motor (N101) wiring is okay, go to next step.
6. Check Secondary Air Pump Relay (J299) and Secondary Air Pump Relay (J299) wiring. See DTC
P0418/16802: SECONDARY AIR PUMP RELAY (J299), MALFUNCTION . Repair or replace as
necessary. Erase DTC memory. Verify repair. Test is complete. Perform ECM relearn procedure. See
TEST DRIVE RELEARN PROCEDURE .
7. Disconnect vacuum hose from Secondary Air Injection Valve (N112) and disconnect pressure hose from
secondary air pump motor, press buttons on pressure hose connector to disconnect pressure hose. See Fig.
34 . Blow lightly into disconnected pressure hose, Combi-Valve should be closed. Connect hand vacuum
pump to disconnected vacuum hose and apply vacuum to Combi-Valve, Combi-Valve should open. If
Combi-Valve opens when vacuum is applied, Combi-Valve is okay. Go to next step. If Combi-Valve
does not open when vacuum is applied, replace faulty Combi-Valve. Erase DTC memory. Verify repair.
Test is complete. Perform ECM relearn procedure. See TEST DRIVE RELEARN PROCEDURE .
8. Check Secondary Air Injection Valve (N112). See DTC P0412/16796: SECONDARY AIR
INJECTION VALVE (N112), ELECTRICAL CIRCUIT MALFUNCTION . Repair as necessary.
Erase DTC memory. Verify repair. Test is complete. Perform ECM relearn procedure.
NOTE: Do not use compressed air to check Combi-Valve.
2000 Volkswagen Passat GLS
2000 ENGINE PERFORMANCE Self-Diagnostics - 1.8L Turbo

Jun 21, 2008 | 2000 Volkswagen Passat 4Motion

Not finding what you are looking for?
2008 Hummer H3 Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hummer Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Brandon Johnson
Brandon Johnson

Level 2 Expert

251 Answers

Are you a Hummer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...