Question about 1991 GMC Sonoma

1 Answer

Check engine light code 24 - 1991 GMC Sonoma

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Legend:

    An expert who has written 200 answers of more than 400 characters.

  • Expert
  • 331 Answers

Code 24 refers to VSS (vehicle Speed Sensor) this sensor is located externally, on the drivers side of the transmission. The ECU is not detecting the speed inside the trani. I hope that helps. let me know if you need more info. Good luck.

Posted on Mar 03, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

When i drive the car the check eng light comes on then in a bit it will go out I check for code's but there's no code's?


You can only check the code whilst the light is on. Leave the code reader plugged in. When the light comes on, pull over if safe to do so and read the code reader.

I had a similar thing on my Lexus. It was a thermostat sensor that was telling the engine stayed hotter than it should for a while until the thermostat opened.

Dec 17, 2015 | Cars & Trucks

1 Answer

Check engine light


It means that there is a malfunction with the engine control system which is most likely related to the emission control system, the computer stores some diagnostic trouble codes that should be retrieved, the trouble code numbers will help to find where the problem may be. The way to get the trouble codes is by putting a jumper wire in the diagnostic connector under the hood between the terminals TE1 and E1 with the key on the check engine light will blink the code, for example a code 24 would be two blinks followed by four and so on. Once the codes are known you can reply back to me and I can help further.

Nov 27, 2011 | 1991 Toyota Camry

1 Answer

Engine light on , surges, light blink codes..12, 24 and 55


12 means battery has been disconnected recently
24 is the one to concentrate on, which is showing a fault at TPS. (Throttle position sensor )
55 is end of message or codes.

I'd check and clean connector on TPS, if that doesn't help, replace TPS.

Feb 24, 2011 | 1991 Plymouth Acclaim

2 Answers

Check Engine light. Misfire Cylinder 4. Keeps coming back


it sounds like an intake vacuum leak to me. check with propane or acetylene

Nov 07, 2009 | 2001 Dodge Caravan

1 Answer

The check engine light blinked 3 3 1 3 3 any ideas


code 33 = EGR valve not opening or not closing.
331-133 not listed.

Oct 12, 2009 | 1995 Ford Taurus

1 Answer

I have a check engine light with a 12 and 24 code followed by the55 code . The car is often difficult to start.It's 1992 Dodge Spirit with a 4cy. engine.


Code 12 is battery disconnected lately. code 24 is faulty TPsensor. code 55 is end of message.
So, I'd replace my throttle position sensor.

Jul 07, 2009 | 1992 Dodge Spirit

1 Answer

I have codes 22,24,and 12 that i pulled, car dieds sometimes at the lights and check engine light stays on.


Hello;
Check your coolant. It may be low and overheating your engine to the point of shut down. Code 22 is the coolant sensor, code 24 is the intake air sensor and 12 is no RPM or NE signal.
Thanks;
Rich
RPM Northwest

Jun 11, 2009 | 1995 Toyota Camry

2 Answers

1997 isuzu wizard mu check light


Code 24 is a vehicle speed signal sensor fault, the sensor most likely does not provide a useable signal until about 25 MPH, when the computer doesn't see any signal after that speed it turns on the light. Make sense?

Sep 08, 2008 | 1997 Isuzu Oasis

Not finding what you are looking for?
1991 GMC Sonoma Logo

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...