Question about 1995 Ford Windstar

1 Answer

When I turn the key the starter will not engage when I get under it I can jump the starter and it will run

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 43 Answers

Sounds like a problem with the ignition cylinder. Could also be a bad starter fuse.

Posted on Feb 08, 2014

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1596 Answers

SOURCE: Starter

Seems to Be A Starter Solinoid Problem

Posted on Feb 26, 2009

  • 335 Answers

SOURCE: i have 1985 f150 4x4

Check/replace the neutral safety switch on the transmission.

Posted on Mar 20, 2011

  • 1 Answer

SOURCE: need location of starter relay fuse my explorer

I already replaced the starter and it still clicks but also still turns on it has a slow start. What is it?

Posted on May 25, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Good battery, key will not engage starter, jumping starter will not engage drive


jumping across the solenoid will spin the starter but will not engage the pinion in the ring gear. Have a load test done on the battery as I suspect that there is a bad cell and you are not getting a full charge. If the battery is faulty then there is always enough power to turn on dash lights but nothing left to run the high current solenoid and starter.

Dec 23, 2013 | Cars & Trucks

1 Answer

Fist of all the ignition switch tuns with out key its been laid up seveveral years.had to jump solinoid to get engine to run .so i replaed solinoid nowwhen you turn the key nothing happens youneed to jump...


As the car has been laid up many years, it needs a thorough servicing. Besides a solenoid in the starter motor, there is a bendex as well. Its role is to push the starter pinion forwards to enable it to engage the flywheel when you turn the key. And when the key is turned backwards then this pinion is pulled backwards. This goes bad sometimes as most of the things do. So it should be repaired. Then the starter motor will start functioning as it should.

Oct 14, 2010 | Ford Ranger Cars & Trucks

1 Answer

Turn the key on and the lights radio fuel pump everything comes on but it will not crank, replaced neutral switch, checked ignition switch, hot wire to relay center under hood, if you jump out the starter...


Sounds like the starter solinoid especialy if the starter works when you jump it. I dont know if you can buy just a solinoid for that particular car, but its a cheap place to start if you can. If not you should be able to get a whole remaned starter for around a hundred bucks. Hope this helps.

Mar 27, 2010 | 1995 Buick LeSabre

1 Answer

I got a 89 bronco II and it wont start. Its got a new battery. I jumped out the starter relay and the starter engaged. So thats good. Also the relay clicks when you turn the key. Also checked the...


Im not sure what you mean by I jumped out the starter relay and the starter engaged.
so i am going to assume that you jumped from the battery side to the starter side on the relay and that engaged the starter... which is fine but you say the relay clicks when u turn the key. Pull off the clip on wire from the relay and push it against the battery side connection on the relay (u may need a small screwdriver to assist the connection) the relay should cause the starter to engage. If it just clicks (my bet) then you need to replace the relay (its really called a solenoid )

Feb 14, 2010 | 1989 Ford Bronco II

1 Answer

Van wont start when key is turned


sometimes when one replaces the ignition a small plastic part falls from the new ignition causing it not to fully engage-for fun turn key with a liitle firmness all the way to sart-sometimes with added pressure it engages-orthewise remove ignition for examination

Sep 25, 2009 | 2003 Dodge Caravan

2 Answers

Turn the key on and the starter will not engage.


check fuel pressure.if not above recomended spec. replace fuel pump. for starting have solenoid 0n starter checked.

Jan 26, 2009 | 1994 Cadillac Fleetwood

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77194 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

fordexpert

Level 3 Expert

5579 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...