Question about Mercury Cougar

1 Answer

Blower control switch

How do I install the blower control switch on a 1999 MErcury Cougar? I have no clue how to get the panel off that I assume needs to be removed to install it.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer got voted for 20 times.

  • Mercury Expert
  • 251 Answers

The cover should pry off if you dont see any screws holding it on.

Posted on Jan 17, 2015

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
chuck943
  • 783 Answers

SOURCE: Mercury Cougar heater blower only works on high.

remove the trim panel below the glove box and you will see the blower motor,just to the left of it you will see a 4 wire connector plugged into the case. This is the blower motor resistor,this is what you need to replace.

Posted on Feb 12, 2009

  • 1183 Answers

SOURCE: Where do you find Diagram on 1999 Mercury Cougar

http://www.autozone.com/addVehicleId,2523402/initialAction,repairGuide/shopping/repairGuide.htm?pageId=0900c152800a8c49
Try this web site. I was able to find what you are looking for. Just fill in your info for your vehicle.

Good Luck

Posted on Mar 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The motor stalls when the heating direction knob is turned on


2002 Mercury Cougar V6 2.5L problem - YouTube

? 2:28
https://www.youtube.com/watch?v=zUu256ADwJA
Jun 2, 2012 - Uploaded by 1chrisrg
U know how to adjust idle speed manually on 2000 mercury cougar? ... You may drive and the hole is too small and the coug will stall. .... I replaced the IAC and now if sounds like my engineis in a race ... I just bought a 99 Cougar. ... new edge cougar owners forums and I believe there are directions on ...

How to replace heater control panel switch knobs remove ...

? 5:01
https://www.youtube.com/watch?v=abBINs_zWh8
Jul 12, 2013 - Uploaded by kirk colombo
02 explorer - remove dash panel and replace heater and air conditioning control switch knobs. Can also ...Missing: cougar ‎stalls

A/C & Heater Controls for Mercury ' eBay




Dec 13, 2015 | 1999 Mercury Cougar

2 Answers

Blower motor removal in a 1999 mercury cougar


SECTION 412-02: Heating and Ventilation 1999 Cougar Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 02/8/2001 Blower Motor Removal
  1. Remove the footwell upper trim panel (passenger side).
    • Remove the pushpins.
    m3401035.jpg
  1. Remove the blower motor.
    1. Disconnect the electrical connector.
    1. Lift the securing tab, turn the motor approximately 30 degrees counter-clockwise and remove the motor.
    m3401077.jpg
Installation
  1. NOTE: Engage the securing tab for the blower motor.

Nov 12, 2010 | 1999 Mercury Cougar

1 Answer

1999 mercury cougar. 3 of my 4 blower settings for a/c stopped working 6 weeks ago and today the 4th went out. i had the blower test and is fine. I replaced the blower resistor and blower switch and still...


Make sure you contact a Mercury Dealer or Ford Dealer and run your vehicle ID number to see if it has a recall on the blower switch. I worked for Ford for years and I think I remember that vehicle having a blower switch and or relay recall. Some of these recalls did not expire and if that is the case it would not cost you anything to have this done. Good luck, hope this helped

Feb 06, 2010 | 1999 Mercury Cougar

1 Answer

How do i change a blower motor in a 1999 mercury cougar


Blower Motor Removal
  1. Remove the footwell upper trim panel (passenger side).
    • Remove the pushpins.
  1. Remove the blower motor.
    1. Disconnect the electrical connector.
    1. Lift the securing tab, turn the motor approximately 30 degrees counter-clockwise and remove the motor.

Jan 10, 2010 | 1999 Mercury Mountaineer

1 Answer

1999 mercury cougar,overheats ,I have install new waterpump,have radiator clean and remove thermostat,radiator fans do turn on.I'm lost.


Sounds like a blown head gasket .But thats easy bad relay switch or coolant temp switch or bad resistor.

Nov 24, 2009 | 1999 Mercury Cougar

1 Answer

EGR VALVE 1999 MERCURY COUGER


SECTION 303-08: Engine Emission Control 1999 Cougar Workshop Manual REMOVAL AND INSTALLATION Exhaust Gas Recirculation (EGR) Valve Removal
  1. Remove the air cleaner outlet tube.
    1. Disconnect the intake air bypass hose.
    1. Disconnect the positive crankcase ventilation hoses.
    1. Remove the air cleaner outlet tube.
  1. Disconnect the tube from the exhaust gas recirculation valve.
  1. Remove the exhaust gas recirculation valve.
    • Disconnect the vacuum hose.
Installation
  1. sxu~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: When cleaning the gasket faces, do not allow debris to enter the intake manifold or exhaust gas recirculation valve.
    Clean the gasket faces of the intake manifold and exhaust gas recirculation valve.
  1. Install a new exhaust gas recirculation valve gasket.
  1. Position the EGR valve and install the bolts.
    • Install the vacuum hose.
  1. Connect the EGR tube.
  1. Install the idle air control valve. For additional information, refer to Section 303-14A . For additional information, refer to Section 303-14B .

Sep 15, 2009 | 1999 Mercury Cougar

1 Answer

Blower motor fuse is located 99 mercury cougar


SECTION 412-04: Control Components 1999 Cougar Workshop Manual REMOVAL AND INSTALLATION Blower Motor Resistor Removal
  1. Remove the upper footwell trim panel (passenger side).
    • Remove the pushpins.
  1. Disconnect the blower motor resistor electrical connector.
  1. Remove the blower motor resistor.
-------------------------------------------------------------------------
f9d16f6.gif

May 06, 2009 | 1999 Mercury Cougar

1 Answer

Ignition switch


Remove the 3 screws form the steering column lower shroud.
Then remove the 2 screws from the ignition switch and remove.
http://i253.photobucket.com/albums/hh43/chuck943/cougarignitionswitch.jpg

Mar 15, 2009 | 1999 Mercury Cougar

2 Answers

Mercury Cougar heater blower only works on high.


remove the trim panel below the glove box and you will see the blower motor,just to the left of it you will see a 4 wire connector plugged into the case. This is the blower motor resistor,this is what you need to replace.

Feb 12, 2009 | 1999 Mercury Villager

1 Answer

1999 mercury cougar bloswer motor removal


Yes there is a samll tab located on the bottom, if you bend it down and twist it should spin right out.

Jun 20, 2008 | 1999 Mercury Cougar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

fordexpert

Level 3 Expert

5546 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...