Question about Cars & Trucks

Open Question

How to remove face plate to fit radio of K2700 2013 model

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ironfist109
  • 3018 Answers

SOURCE: REPLACE RADIO ;HOW DO

  1. Pull open the cup holder.
  2. Pry the little panel above the cup holder off.
  3. There are two screws you can now see. Remove them.
  4. Now you want to carefully remove that panel. There are a few clips that will be removed as you remove that panel.
  5. You will now see some screws holding the radio itself in place. Remove them screws and the radio is ready to be pulled forward.

Regards, Tony

Posted on May 10, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i remove the stock radio from my 1993 geo metro 4 door hatchback


here is the online fsm quote

  1. Disconnect the negative battery cable.
  2. Open the glove box. Remove the glove box open panel.
  3. Remove the air conditioning switch connector and heater control unit lever knobs. Pull heater control unit cover plate from instrument panel.
  4. Remove the gearshift control lever upper boot and center console.
  5. Remove the ashtray.
  6. Remove the instrument panel center trim bezel and radio face plate.
  7. Remove the screw from the back of the radio receiver and the screws from the front face of the radio.
  8. Remove the radio.

Sep 30, 2014 | 1993 Geo Metro

1 Answer

HOW TO REMOVE 2004 FORD FOCUS BLAUPUNKT RADIO FACE PLATE


No, you will damage the face plate trying to do that. The dealer has a special tool that is unique to properly remove the unit.

Dec 20, 2013 | Cars & Trucks

1 Answer

Poineer rsm-400 reset setting


remove the face plate and there is a small hole in the front of the radio head unit that a paperclip will fit into.

Mar 26, 2013 | Cars & Trucks

1 Answer

Car radio removal


remove dash face plate around radio there will be small screws or studs with nuts around the sides of radio attached to a mounting plate. Unhook wire harness on radio and pull from dash

Mar 02, 2010 | 1995 Geo Prizm

1 Answer

Removal of radio 2006 e450


you should see 4 holes on the face plate find a nail that fits in the hole push them inand leave them in. if you released the catches the radio will slide out

Feb 01, 2010 | 2005 Ford E-Series

1 Answer

How do i get the dash off to pull the old radio out


I'm not totally sure about the La Sabre, but there should be trim screws that hold the Dash face plate in place. There are three on the top portion of the face plate, and I think three on the bottom . The face plate extends from Light switch on left to radio on right. You may have to tilt the steering wheel column down to remove the face plate from around the steering wheel. From what I remember, the only thing that needs to be unplugged from the face plate is the plug for the rear defroster. Also, there are clips that hold the face plate in place. They just push in and out. Once the face plate is off, you can get to the radio mounting screws.











Aug 16, 2009 | 1993 Buick LeSabre

1 Answer

Radio and dash lights


Remove radio from vehicle. remove T15 torx screws on top and sides of radio. Remove knobs and outer bezels around knobs. Face has retainer clips top and bottom. Unsnap the face of radio and remove old bulbs there are five or six in a gm radio.

Jan 12, 2009 | 2001 Chevrolet Blazer

1 Answer

How i install car stereo in sonata


I have a 2004 Sonata and I'm currently in the process of installing a new stereo system. It's really easy to remove the original radio, you just have to remove the wooden panel face plate that surrounds the radio and air vents.

There are two notches that pretty much lock the face plate on. Right above the ash tray and the bottom of the wooden panel face plate, there's a tiny notch that you can push up on. There's another one that's hidden right above the cigarette lighter. Just push a flat-blade screw driver into both notches and gently push up. Once you lift that up, slowly pull it towards you, and keep prying it open starting from the bottom and moving towards the top. Make sure you pull on it carefully since the air vent ducts and wiring for the fan controls are attached to the face plate. I didn't have to remove the wiring for the fan controls, since I was able to easily move the entire face plate out of the way.

There are four screws that hold the radio in place. Keep in mind, these are screwed in by some machine, so I'd recommend using a power screw driving so you don't end up stripping the screws. Once you remove the four screws you can easily slide out the radio and unplug the wiring harness and antenna.

I searched a lot of places for a converter that would fit directly from the wiring harness in the car to the plug in my new radio, but to no avail. I'm at the point now that I'm going to cut off the original harness in the car and splice the wires, and connect them to the new radio's wires using a crimper. It's really not that hard, but I wanted to avoid cutting and splicing since I previously thought you would lose a lot of sound quality. It turns out, I spoke with several people who did the same thing, and as long as you crimp the wires together properly, you really don't lose out on the sound quality. It's a fairly easy task since all the wires are color-coded, so just match the wires, splice just enough for it to fit inside the caps, and crimp them together.

Then just plug in the adapter into your new radio, screw it in, and you're good to go! I wish there were more adapters out there, but it looks like more and more cars are changing their wiring harnesses, probably to discourage us do-it-yourselfers and pay some insane amount of money to some chump in a dealership garage. Don't be discouraged though! It's really not that hard!

Dec 18, 2008 | 1999 Hyundai Sonata

1 Answer

Removal of radio


1. disconnect battery lead because of air bag sensors
2. pop off trim around shifter stick
3. remove center knob on the A/C panel. Remove phillips screw behind the knob. This is the only screw that has to come out (in addition to the 4 radio screws)
4. pull the a/c console forward. It's a tight fit but it's only held by clips. This was the most difficult part for me because I didn't want to break anything. It eventually released after pulling with constant pressure.
5. pull the air vent assembly off around the radio. This is also a tight fit, is only secured with clips. The radio face plate came off with this piece.
6. Remove 4 10mm bolts at bottom of radio. I used putty on a 10mm socket to help hold the bolt from falling down into the dashboard. Lose these bolts and you'll easily add several hours to the job trying to fish them out of the dashboard.

Hope this helps

Oct 10, 2008 | 2006 Toyota Corolla

1 Answer

1998 beetle radio buttons


The face plate buttons actually activate small buttons on a printed circuit board behind the face plate. When I removed the radio and then the face plate many small pieces of plastic fell from behind the face plate. These small plastic pieces align the face plate button to the printed circuit board buttons. My Beeetle is almost 10 1/2 years old so I imagine the plastic is just becoming brittle with age. I could not set the radio to FM, so I removed the face plate button and now slide a toothpick in the slot to toggle between FM1 & FM2. Not he best solution, but probably the most inexpensive one. I also made my on tool to remove the radio from a diagram found at: http://www.alientech.net/nbinfo/stereo.html

Jul 02, 2008 | 1998 Volkswagen Beetle

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...