Question about Chevrolet Tahoe

Open Question

Stabilization track service light on in Chevy Tahoe 2007

What reason would it stay on

Posted by Anonymous on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 607 Answers

SOURCE: the service stability light is on

It pertains to just what it says STABILITY. Your vehicle has a system that will sense if you are coming around a curve at about 90 MPH. It will automatically apply a light amount of braking to the proper wheels, thus hopefully eliminating you and your Uplander from flying off curve. With the light on as with any warning light , you must assume whether its real or not, that the STABILITY system IS NOT operating. Significant computer / sensor diagnosis will be necessary. Hope this helps

Posted on Apr 12, 2009

  • 262 Answers

SOURCE: airbag light stay on 2003 chevy tahoe

The air bag light will remain illuminated if a fault has been detected in the air bag system.
The onboard computer will need to be interfaced with diagnostic equipment to read the fault.
This is also the only way to reset the light.
Good luck, I hope this helped.

Posted on Mar 13, 2010

  • 15288 Answers

SOURCE: 2007 chevy tahoe driver side door handle will not open door

the linkage behind the handle either the retaining clip broke or popped off need to remove the door panel to check and fix

Posted on Mar 13, 2010

Testimonial: "Thanks I thought it might be a cable or linkage. Much thanks"

  • 312 Answers

SOURCE: how to change the brake light on a 2007 chevy

Open the rear hatch and locate the area behind the light you wish to change. You will see two screws that hold the assembly in place. Remove those two screws and push the pins through and the whole assembly will pop out allowing you to access the bulb by twisting the connection and pulling it out. Installation is the reverse. Good luck.

Posted on Jun 10, 2010

  • 1450 Answers

SOURCE: 2004 Tahoe with the following

It is a problem with your abs this will cause traction and stability to turn off as they work off abs system. need to have scanned for codes. ebcm is common about going out on these

Posted on Oct 12, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Parking brake light stays on. 2008 Chrysler Sebring.

the brake light will stay on for two reasons. the switch is bad so when you pull the handle the switch is not being moved like it should and since its out of adjustment it wont know the lever moved. the other reason is the sensor on the abs system thinks there is a problem with the hydraulics and keeping the light on till it problem is resolved. your problem is it could be either and figuring out which will be a problem. the switch on the ebrake handle is the easier one to check. unplugged the switch and see if the light goes out. if it does then replace the switch or adjust it so it works the correct way.

Nov 08, 2017 | Chrysler Cars & Trucks

1 Answer

I have a 2001 Nissan maxima gle 3.0 and my battery light is staying on I checked the positive and the the vehicle stays running what could be a few more reasons why it would stay on

It could be a bad alternator. Start the car, then try disconnecting the positive battery cable to the battery after the car is running. If it stays running, the alternator is good. If the car dies, alternator no good.

I’m happy to help further over the phone at

Jul 19, 2017 | Nissan Cars & Trucks

1 Answer

2008 chevy Tahoe LTZ Traction control and stability track service message

have truck scanned for code can be simple as a sensor to hub problems

Jul 02, 2017 | Cars & Trucks

1 Answer

Abslight stays on. How to fix? This is a2007trailblazer?

First you need to have EBCM - electronic brake control module check for DTC'S - diagnostic trouble code's . If the light is on there is a code stored . I think most part stores can do this and for free . After you find out what code is stored , looking up that code in service repair information for diagnostic trouble shooting chart would be next step . There are a few codes too.
DTC C0035 or C0040
DTC C0045 or C0050
DTC C0110
DTC C0131
DTC C0161
DTC C0186
DTC C0196
DTC C0201
DTC C0240
DTC C0241 or P0856
DTC C0244 or P1689
DTC C0245
DTC C0283
DTC C0287
DTC C0290 or C0292
DTC C0455
DTC C0550
DTC C0558

Find the code do the diagnostic's , fix the problem , wiring issue's , a sensor , bad module ,what ever it is . The light will go out then . Here is a sample of code discription .
• DTC C0035 Left Front Wheel Speed Sensor Circuit
• DTC C0040 Right Front Wheel Speed Sensor Circuit

Dec 30, 2016 | 2007 Chevrolet Trailblazer

1 Answer

Why would srs light stay on in my mitsubishi lancer 2003 model

A common reason is that the clock spring assembly in the steering wheel has failed. Next reason is the SRS computer has a problem.

Feb 20, 2015 | 2003 Mitsubishi Lancer

1 Answer

My stability track system light is on in my 2007 Tahoe and it drives like the motor is about to fall apart can you give me some advice

run fault codes to see if there is a sensor problem that has to be fixed. You have 2 problems occurring . One is probably a rotor sensor for the stabiliser and the other is probably a O2 sensor problem or injector faults.

Jun 28, 2014 | Cars & Trucks

1 Answer

Stability track

This is a common problem with GM's. The TPS sensor goes bad in the throttle body. Throws out a message to service Stabilitrac. Not SO!!!
The kicker is that the whole throttle body has to be replaced because the TPS sensor is actually part of the throttle body!!! Costs around $250.00 for aftermarket.

Oct 15, 2012 | 2007 Chevrolet Tahoe

1 Answer

SRS light stays on vrx lancer 02 how do I turn it off please!

use a scanner to confirm the cause of light stayed on. Sometimes the reason is under the seat of driver or front passenger as they are moved either forward or backward and one slight reason is the connector under the seat is not well connected -moved- and have not a good contact and light comes on.

Sep 06, 2012 | Cars & Trucks

1 Answer

Cooling fan comes on and stay on

Is the system low on coolant for some reason? this would be the reason if it is. If you did any service to the cooling system did you bleed the air out of it as required?

Jul 17, 2012 | Vauxhall Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

80407 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides