Question about 2011 Dodge Avenger

Open Question

Serpentine belt diagram for 2011 2.4 L dodge avenger

2.4 L dual vvt

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: serpentine belt diagram:

The belt routing diagram is located on the top radiator cross member by the hood latch. You should see it when you open the hood. If it is not there, all Chrysler, Dodge, and Plymouth minivans, from 1993 to at least 1999, used the same 3.3L engine setup, so find someone with one and look for the diagram where I described.

Posted on Jul 18, 2008

  • 3 Answers

SOURCE: need diagram for 2000 dodge dakota serpentine belt

On the 1999 Dakota with the 3.9liter, the fan shroud absolutely DOES NOT have to be removed. Very simple job. Simply use a breaker bar with a 15mm socket on the belt tesioner pulley nut. Using the breaker bar push (as though tightening) the pulley nut...the reaction will be that the tensioner removes tension from the pulley and the entire belt can be removed by easily slipping it toward the front of the vehicle...comes right off. The new belt can go back on in exactly the same manner. By the way the belt routing diagram IS CONVIENENTLY LOCATED between the hood latch and the radiator mounting for simple and quick refernce...one person job, I did removal and installation four times in less than 10 minutes. (why four times? The auto parts store was selling replacement belts that were too long and did not allow the belt tensioner to provide suffiecient tension...I had to try four different manufacturers before the tensioner was adequately tight with room to grow as the belt naturally stretches from use.). I found no stringing around the fan is required because of the way the belt is routed (it doglegs around the main engine pulley which is centered below the fanhousing and then the belt runs from there to the left side of the fan housing...avoiding the fan/fanhousing all-together (sure you can try to go past the fan/fan housing if you so desire...but you dont have to...and besides the space between the pulleys and the fan is ample to allow the belt to pass between with minimal interference or a simple rotation of the fan as you attempt this method. One hint that made my installs easy as pie...the last pulley you put it over should not be a bezeled and ridged pulley or you will needlessly make life difficult for yourself...the last pulley should be the water pump pulley which is a smooth bore and non-ridged pulley (makes you wonder how the belt even stays on it!)...making it easy as pie to slip it right over...as your last act of defiance to that mean old serpentine belt!

Posted on Jan 17, 2009

BCally1
  • 133 Answers

SOURCE: serpentine belt diagram for a 5.9 diesel with air and 9 pulleys

5.9L DIESEL
196759.jpg The 5.9L diesel engine accessory drive system (with a/c) consists of :

  1. Generator Pulley (1)
  2. Water Pump Pulley (2)
  3. Idler Pulley (3)
  4. Power Steering Pump Pulley (4)
  5. Radiator Fan Pulley (5)
  6. Crankshaft Pulley (6)
  7. Automatic Tensioner (7)
  8. A/C Compressor Pump Pulley (8)
CAUTION: When installing the accessory drive belt, the belt must be routed correctly. If not, engine may overheat due to water pump rotating in wrong direction. Refer to or for correct engine belt routing. The correct belt with correct length must be used.
1. Position drive belt over all pulleys except water pump pulley. 2. Attach a 1/2 inch ratchet to tensioner.


196757.jpg The 5.9L diesel engine accessory drive system (without a/c) consists of :
  1. Generator Pulley (1)
  2. Water Pump Pulley (2)
  3. Idler Pulley (3)
  4. Power Steering Pump Pulley (4)
  5. Radiator Fan Pulley (5)
  6. Crankshaft Pulley (6)
  7. Automatic Tensioner (7)
3. Rotate ratchet and belt tensioner clockwise. Place belt over water pump pulley. Let tensioner rotate back into place. Remove ratchet. Be sure belt is properly seated on all pulleys.

Posted on Jan 22, 2009

localwonder
  • 6784 Answers

SOURCE: diagram for a serpentine belt replacement for 2000 avenger dodge

HI. i have posted the diagram requested below.

7109f62.jpg

Posted on Aug 24, 2009

Testimonial: "This was exactly what we needed, Thank you so very much. "

  • 1757 Answers

SOURCE: Need serpentine belt routing diagram for 1994 Dodge grand caravan

3.3L?
Looking at the engine from front (right side of the Van): Stating at the Top, Going Left to Right and Clockwise:
Over the Alternator
To under the Idle Pulley,
To Over the AC Compressor.
To the Left Side of the Water Pump.
To the Right side and Under the Crankshaft Pulley
To the Right side and Over and Down the Tensioner
To Under the Power Steering Pump
And Back up-to the Left side of the Alternator.
Advise when puting it on:
Put the Belt around everything else accept for the Alternator. After it is around all the rest of the Pulleys - Pull the belt up - tight from the Power steering Pump and the Idle Pulley to form a loop, holding the Belt close to the Altenator Pulley.
Using the 15mm wrench or belt tensioner bar - rotate the Tensioner Pulley towards the front of the Van and then place the belt over the Alternator.
Let me know if this helped or if you have additional information or questions. Feel free to contact me at FixYa.com!

Posted on Jan 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need a diagram for a 2011 dodge 2500 cummings serpentine belt.


Jeff, Check the attached links,instruction and guides, diagram for a serpentine belt, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Amps Belt routing Installation and system start up for 6 7L Cummins
Serpentine Belt Routing
Drive belt routing
2011 dodge 6 7 cummins serpentine belt diagram Google Search

May 22, 2016 | 2011 Dodge Ram 2500

1 Answer

How 2 turn off seat belt light 2011 dodge avenger?


Pull on the front seat belts a few times

If the rear ones are use- try them also

Nothing--- you will need a scan tool to check the
SRS Module for codes

Nov 21, 2014 | 2011 Dodge Avenger

1 Answer

2008 dodge avenger serpentine belt diagram


Is it not on top of your radiator area, or underside of hood? What engine?

Apr 19, 2013 | 2008 Dodge Avenger

2 Answers

Belt route 2011 dodge avenger


I find this diagram that I hope that help you...


10_3_2011_12_27_53_am.jpg

Oct 02, 2011 | 2011 Dodge Avenger

2 Answers

2.4 Dodge avenger belt Diagram


I find this diagram AVENGER Engine L4 2.4L 2360cc 144ci GAS FI N K that I hope that help you...


10_3_2011_1_14_07_pm.jpg

Oct 02, 2011 | 2011 Dodge Avenger

1 Answer

I need a diagram for the serpentine belt without a/c on a 1996 dodge avenger


should be under the hood some where or in the owners Manuel if you havent looked in those places i would try that first

Jul 06, 2009 | 1996 Dodge Avenger

Not finding what you are looking for?
2011 Dodge Avenger Logo

Related Topics:

162 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...