Question about 1997 Chevrolet C3500

Open Question

I can' find the radiator drain pitcock, for the life of me, on this 95 chevy conversion van-G20

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
chiquititas
  • 1010 Answers

SOURCE: 1987 Chevy G20 van replace power steering pump

Does your van have the serpentine belt? If so maybe I can help, I replaced the Power steering pump on my 90 G20 a couple of weeks ago. The trick is that you need to pull the pump pulley which is pressed on to access the mounting bolts which attach the pump to the engine. Harbor Freight tools sells a great tool designed for this job for $20.00. Once you have the correct tools, remove the serpentine drive belt. You may also need to remove the fan shroud. the pump shaft looks like it has an allen socket in the center, but this is for use in the manufacturing process, and will not come out. Place the puller tool on the pulley following tthe instruction that come with the tool, and remove the pulley. loosen, but do not remove the nut on the high pressure hose connection. use a pair of **** pliers to cut and remove the crimp clamp on the low pressure hose. If your pump has the remote reservour loosen the clamp on the reservour hose also. Remove the three mounting bolts, place a large pan under the pump to catch drips, and remove the prevously loosened hoses. there will be fluid leaking all over and the pump should come free, There are two types of replacement pump sold. With and without reservour. This reservour is a metal cover that fits over the back of the pump, and should not be confused with the reomte revervour found on some newer models which is next to the battery. This reservour is held in place be two throught the pump bolts which are removed at the back of the pump. If your new pump has a reservour you will probably still need to remove these bolts and put them in the replacement pump as most are shiped without these bolts. If you replacement pump comes without a reservour pull the bolts, the reservour should pull off of the old pump and slide onto the new one. check the o rings and replace the through the pump bolts. Installation is the reverse of removal execpt that 1/2" hose clamps replace the crimp clamps on the low pressure hose, and the puller tool is set up differently to replace the pulley. Finally if you don't flush contaminants out of the system your repair will last maybe a week. www.cardone.com has a great article about power steering flushing, read it before you start Good luck.

Posted on May 15, 2008

Ad
Shouldibuyit
  • 44 Answers

SOURCE: replace heater core 1994 chevy g20 conversion van

Here a are the instuctions to remove it. I did not know if you have A/C or not so I included both for you.

REMOVAL & INSTALLATION
Without Air Conditioning
ALL MODELS
See Figure 1

  1. Disconnect the negative battery cable.
  2. Remove the coolant recovery bottle.
  3. Place a pan under the van and disconnect the heater intake and outlet hoses. Quickly remove and plug the hoses and support them in an upright position. Drain the coolant from the heater core into the pan.
CAUTION When draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old.
  1. Remove the heater distributor duct-to-case attaching screws and the duct-to-engine cover screw. Remove the duct.
  2. Remove the engine cover.
  3. Remove all the instrument panel attaching screws.
  4. Carefully lower the steering column. Raise and support the right side of the instrument panel. Refer to for further details.
  5. Remove the defroster duct-to-case attaching screws and the two screws attaching the distributor to the heater case.
  6. Disconnect the temperature door cable. Carefully fold the cable back and out of the way.
  7. Remove the three nuts from the engine compartment side of the distributor case and the screw from the passenger compartment side.
  8. Remove the heater case and core assembly.
  9. Remove the core retaining straps and remove the core.
To install:
  1. Install the core.
  2. Install the core retaining straps.
  3. Install the heater case and core assembly.
  4. Fasten the three nuts on the engine compartment side of the distributor case and the screw on the passenger compartment side.
  5. Connect the temperature door cable.
  6. Install the defroster duct-to-case attaching screws and the two screws attaching the distributor to the heater case.
  7. Install the steering column.
  8. Fasten all the instrument panel attaching screws.
  9. Install the engine cover.
  10. Install the duct. Install the heater distributor duct-to-case attaching screws and the duct-to-engine cover screw.
  11. Connect the heater intake and outlet hoses.
  12. Fill the cooling system.
  13. Install the coolant recovery bottle.
  14. Connect the negative battery cable.
1990-95 MODELS With A/C

  1. Disconnect the battery ground cable.
  2. Remove the engine cover.
  3. Remove the steering column-to-instrument panel bolts. Lower the column carefully.
  4. Remove the upper and lower instrument panel attaching screws. Remove the radio support bracket screw.
  5. Raise and support the right side of the instrument panel.
  6. Remove the lower right instrument panel bracket.
  7. Remove the vacuum actuator from the kick panel.
  8. Disconnect the temperature cable and vacuum hoses at the case. Remove the heater distributor duct from over the engine hump.
  9. Remove the two defroster duct-to-firewall attaching screws below the windshield.
  10. Under the hood, disconnect and plug the heater hoses at the firewall.
  11. Remove the three nuts and one screw (inside) holding the heater case to the firewall.
  12. Remove the case from the van. Remove the gasket for access to the screws holding the case together. Remove the temperature cable support bracket. Remove the screws and separate the case. Remove the heater core.
To install:
  1. Install the heater core.
  2. Assemble the case and fasten the screws.
  3. Install the temperature cable support bracket.
  4. Position the gasket, then install the case in the van.
  5. Fasten the three nuts and one screw (inside) holding the heater case to the firewall.
  6. Connect and plug the heater hoses at the firewall.
  7. Fasten the two defroster duct-to-firewall attaching screws below the windshield.
  8. Install the heater distributor duct.
  9. Connect the temperature cable and vacuum hoses at the case.
  10. Install the vacuum actuator at the kick panel.
  11. Install the lower right instrument panel bracket.
  12. Fasten the radio support bracket screw.
  13. Fasten the upper and lower instrument panel attaching screws.
  14. Fasten the steering column-to-instrument panel bolts.
  15. Install the engine cover.
  16. Connect the battery ground cable.
  17. Refill the cooling system as necessary.

Posted on Nov 28, 2008

GM Elec
  • 1000 Answers

SOURCE: 95 G20 Chevy van: ABS light stays on, pulls right when braking

You actually have two separate problems. The brake pull to the right is indicating the left side brake is not working properly. You will want to remove the left front wheel, collapse the caliper piston and make sure the caliper is floating freely on its mounts.
With the piston collapsed you should be able to slide the caliper inboard and outboard of the rotor. If not, you will want to remove the attachment pins, clean and lubricate the pins. If they are grooved or worn you will have to replace them.
The second issue of the ABS light is indicating the system has detected an electrical sensing or control problem. Take the vehicle to your local Auto Zone or Advance Auto and ask them to scan the vehicle for trouble codes. They will scan it for you at no charge.
Chances are you will find a wheel speed sensor problem at one of the wheels.
Write the codes down and respond back, we can start diagnosing the problem,
Good luck, let me know.
Regards,

Posted on Aug 31, 2009

johnjohn2
  • 5763 Answers

SOURCE: routing diagram for a Chevy G20 serpentine belt?

Okay, there are a few engines that come in this van, lucky there the same except,they come with or without ac or airpump, so i will give you all of them and you choose the right one.a613984.gif492790a.giffd1ae03.gif47b4a5f.gif

Posted on Mar 14, 2010

  • 834 Answers

SOURCE: chevy 95 g20 van 8 cylinder wiring order spark

1-8-4-3-6-5-7-2 The #1 spark plug is the front spark plug on the drivers side and the cylinder location in order from front to back on the drivers side is 1-3-5-7 and on the passenger side it is 2-4-6-8. The ignition rotor rotation is clockwise.

If your Distributor cap is not numbered then replace the new wires, or transfer the old ones to the new distributor cap one wire at a time. Identify the #1 spark plug wire and start from there.

Posted on Apr 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Exactly where under the hood of a '95 Chevy G20, van do you disconnect the rear ABS PUMP?


The ABS module is not under the hood.It is under the van floor on the passenger side at about the middle of the van.Slide under the Van at the passenger side cargo door and look up.

Feb 27, 2015 | 1995 Chevrolet G20

1 Answer

How do you remove the back seat from a 1994 chevy g20 van?


I believe the seats are bolted to the floor of the van. Make sure you unplug all electrical connections before removing the seats.

Feb 11, 2014 | 1994 Chevrolet G20

1 Answer

Where would the starter for a chevy g20 conversion van be located?


Starter located under engine on passenger side where engine and trans. meet.

Oct 30, 2013 | 1992 Chevrolet G20

1 Answer

Manual for 1994 chevy g20 custom conversion van


If you need a shop manual for the chassis you can get a used book from Ebay. If it involves lights or other accessories for the conversion part of the van you could try contacting the company that did the original conversion. I doubt they print books with diagrams for the public.

Jan 08, 2013 | Cars & Trucks

2 Answers

Need a guide of where the fuses go on a 95 Chevy G20 Van


The fuses are located on a fuse block, they provide increased circuit protection and reliability. The fuse block is located under the left side of the instrument panel and steering column. The fuse block should be visible from underneath the steering column, near the pedal bracket. If the block is not visible, check for a removable compartment door or trim panel which may be used on later models to hide the block. On 1996-97 models, there is also a fuse/relay panel mounted underhood.

e5fef9f.jpg

Fig. 1: If the fuse panel has a concealed cover, unscrew or unclip the retainer and remove the cover:

18e20c4.jpg

Fig. 2: Some fuse panel covers contain a fuse puller, spare fuses and a diagram of the fuse locations:

Good luck (remember rated this help).

Mar 02, 2010 | 1995 Chevrolet G20

1 Answer

Can i swap a 95 chevy v8 where a 95 chevy v6 was? it's a g20 3/4 ton van & i think the head gasket in the v6 might be shot.


Anything can be done. Just how busy do you want to be. Like for Like is always easier and faster. Just don't get over your head and end up spending too much time and money and calling it quits.

Jan 15, 2010 | 1995 Chevrolet G20

2 Answers

I inherited a G20 gladiator chevy van and cannot figure out how to get the spare tire cover off the back door??? It sounds stupid, I know.


Most likely Gladiator conversion vans disappeared like many of the other conversion van companies. I am not familiar with Gladiator vans, but most of the conversion vans use the same setup. The chrome ring around tire is latched near the bottom, and usually padlocked to keep others from stealing your spare. If that is not the case, try http://www.v-sales.com/repair.htm . They still sell conversion parts and may be able to help you. Hope this helps

Sep 29, 2009 | 1993 Chevrolet G20

1 Answer

93 chevy g20 van interior lights not working


Auto Zone, Discount Auto, Pep Boys

Sep 16, 2009 | Cars & Trucks

2 Answers

Electronic Control Module Installation 1994 G20 Chevy Van


I just had the same problem. If it is a regular van try under the driver seat in a plastic box. If it is a conversion van try in a pannel just behind driver seat on side of van wall behind a pannel that looks like a vent.

Dec 28, 2008 | 1987 Chevrolet G20

Not finding what you are looking for?
1997 Chevrolet C3500 Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...