Question about 1994 Isuzu Rodeo

Open Question

Stalling when clutch pedal is pressed on 96 .rodeo 2.6ltr

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
price_brucef
  • 65 Answers

SOURCE: 1999 isuzu rodeo LS: Revs high sometimes then revs

Do you have a check engine light? Which engine? My 1996 Trooper with a 3.2 D.O.H.C. is awful for plugging up the E.G.R. I have cleaned it several times! Good Luck!

Posted on Mar 21, 2010

Ad
dttech
  • 4803 Answers

SOURCE: need the diagram for clutch

There's not much to it really, just a mounting bracket, a pedal arm and a simple twist-spring.

dttech_204.gif

Posted on Sep 25, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Trying to find leak in clutch system os 1993 rodeo need diagram


Did you bench bleed the master or slave cylinder ? Is Your Brake pedal Hard ? Could be your Brake booster . send image for more understanding of your problem

Feb 25, 2014 | 1993 Isuzu Rodeo

1 Answer

Manuel trans shifter tough too shift


if you getting a good pressure from the clutch pedal, change out the shifter bushing, that will help some. if you get a poor pressure from the clutch pedal, pressure plate has weaken, need to change out you pressure plate, throw out bearing, since your in the clutch system i would change out the pad also. Old vehicle and high miles, heavy trucks, its common. also check the slave cylinder, make sure it good working operations. worn rubber seal inside slave cylinder will cause a blow-by when press down the pedal therefore, causing to have a weak clutch pedal and hard to shift/engage into gear, same way goes for weak pressure plate. Good luck!!

Nov 09, 2011 | 1994 Isuzu Rodeo

1 Answer

How do i know if my whole clutch is out on my rodeo 99?... the pedal is easy to ingage half way down and im not able to switch gears


At a standstill put the car in 3rd gear and try to get the car to move. If it stalls you clutch is fine. If you able to move the vehicle w/o stalling you need a new clutch.

Apr 09, 2010 | 1999 Isuzu Rodeo

1 Answer

1999 isuzu rodeo LS: Revs high sometimes then revs low to the point it stalls. goes back and forth , won't maintain a level idle. I have to press the gas pedal so it won't stall, so either im stalling at a...


Do you have a check engine light? Which engine? My 1996 Trooper with a 3.2 D.O.H.C. is awful for plugging up the E.G.R. I have cleaned it several times! Good Luck!

Mar 21, 2010 | 1999 Isuzu Rodeo

2 Answers

2002 isuzu rodeo won't start


Look under the dash at the clutch pedal. Should be a switch or a button hidden under there near the top of the pedal. Pull the connector off and put a large paper clip in it, or a short piece of wire, and try the starter. If it doesn't work then check the starter fuse and relay. Just swap the starter relay out with something that you know works like the AC or Fuel pump and see if it starts. If all else fails then it could be the ignition switch itself.

Jul 13, 2009 | 2002 Isuzu Rodeo

1 Answer

My clutch will not depress


Release bearing collapsed.Your slave cylinder has bottomed out so you wont press the pedal any moore.You need to change the whole clutch Assembly

Jun 12, 2009 | 1994 Isuzu Rodeo

1 Answer

Pop & clutch stuck to floorboard


probly the clutch fork or through bearing

Apr 05, 2009 | 1995 Isuzu Rodeo

1 Answer

Tranny problems


did you change the bearing in the flywheel the center one or throw out bearing that pushes out on to the presserplate

Jan 18, 2009 | 1992 Isuzu Rodeo

3 Answers

Low / Soft Clutch Pedal, 1995 Rodeo 2W 2.6L


my rodeo had the same problem i corrected it by bleeding the slave cylinder. and is located on the driver side on the gearbox you will find it if you follow the line from the master cylinder down to the gearbox and if that helps but happens again it might have to be replaced.

Aug 01, 2008 | 1994 Isuzu Rodeo

Not finding what you are looking for?
1994 Isuzu Rodeo Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14378 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...