Question about Cars & Trucks
Posted by Anonymous on
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: 2000 Ford Ranger
TEST B: BATTERY VOLTAGE OUT OF RANGE - DTC B1676
1. Check if vehicle has been jump started within past 2 weeks. If vehicle has been jump started, ABS is
okay. If vehicle has not been jump started, go to next step.
2. Using DVOM, measure voltage between positive and negative battery terminals. If voltage is 9-19 volts,
go to next step. If voltage is not 9-19 volts, diagnose charging system. See appropriate GENERATORS
article in STARTING & CHARGING SYSTEMS.
3. Turn ignition off. Disconnect 25-pin ABS control module. Install EEC-IV 60-pin Breakout Box (014-
00322). Turn ignition on. Measure voltage between breakout box terminal No. 20 and ground. If voltage
is more than 10 volts, go to next step. If voltage is less than 10 volts, repair Light Blue/Pink wire between
ABS control module and instrument panel fuse panel.
4. Turn ignition off. Measure voltage between breakout box terminal No. 25 and ground. If voltage is
greater than 10 volts, go to next step. If voltage is less than 10 volts, repair Red wire between ABS
control module and power distribution box/engine compartment fuse box.
5. Measure voltage between breakout box terminal No. 9 and ground. If voltage is greater than 10 volts, go
to next step. If voltage is less than 10 volts, repair Yellow/Light Green wire between ABS control module
and power distribution box/engine compartment fuse box.
6. Measure resistance between breakout box terminal No. 8 and ground. Also, measure resistance between
breakout box terminal No. 24 and ground. If both resistance measurements are less than 5 ohms, replace
ABS control module and repeat self-test. If either resistance measurement is greater than 5 ohms, repair
suspect Black wire between ABS control module and ground distribution.
NOTE: DTC B1676 will set if vehicle has been jump started.
2000 Ford Ranger
2000-01 BRAKES Anti-Lock - 4WAL - Explorer, Ranger & Mountaineer
Posted on Jun 11, 2008
el codigo lo encuentras en la parte del pasajero abajo del tablero hay una tapa de plastico en la pared de la camioneta quitas la tapa y esta en una etiqueta pegada creo que es en la computadora pero ai esta los codigos yo los encontre ahi ojala te sirva suerte.
Posted on Mar 06, 2009
SOURCE: ver el diagrama donde esta
regularmente buscalo en la distancia del arbol x el exterior o si trae distribuidor el reluctor hace las funciones de sensor de arbol o al frente del arbol busca los conectores con atencion y ubicalos de acuerdo al sensor q controlan espero haber sido de ayuda
Posted on Sep 18, 2010
The Anti-lock Brake System light comes on when there is a problem with your ABS system. It could be a speed sensor, pump, pump circuit, brake switch, or other problems. The ABS computer will store this info to retrieved at a later date. Anyone with a scan tool can do this. Most places charge for this service.
Posted on Jun 06, 2011
Tips for a great answer:
Jul 03, 2015 | Ford Expedition Cars & Trucks
Jan 05, 2015 | Ford Cars & Trucks
Jun 04, 2014 | 2003 Ford Taurus
Feb 23, 2013 | Chevrolet Cars & Trucks
Jul 02, 2012 | 2005 Ford Explorer Eddie
Nov 21, 2011 | 2001 Dodge Grand Caravan
Jun 30, 2011 | 2002 Buick Century
Sep 24, 2009 | 1993 Jeep Grand Cherokee
23 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: