Question about 1996 Cadillac Seville CA Value

Open Question

02 sensors bank 1 sensor 2

Where are they located

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Bank 1 Sensor 1 Location

Tightened the gas cap. Emisions testing left it slightly loose setting off the sensor warnings. Even if it doesn't "look" like it is ose take it off and put it back on tight. If the warnings are still flashing then it prob is the sensor. Caddy's are very touchy about their gas caps!

Posted on Jun 10, 2008

ZJLimited
  • 17970 Answers

SOURCE: location of bank 1 sensor 2

B1S2 is located in the exhaust pipe after the Catalytic converter...

5937c6d.gif


Hope help with this (remember comment and rated this).

Posted on Apr 14, 2010

Testimonial: "ty was helpfull"

  • 15 Answers

SOURCE: I had 2 codes:p0155 and p0135= 02 heater circuit

you say you replced sensors but some times that code could be also be the o2 sensors you should have 2 maybe 4 did you check them

Posted on Apr 15, 2010

  • 266 Answers

SOURCE: need to find the location of bank 2 sensor 2 o2

BANK 2 IS THE PASSENGER SIDE OR THE REAR AND SENSOR 2 IS THE ONE BEHIND THE CONVERTER

Posted on Oct 13, 2010

  • 194 Answers

SOURCE: need to know where the

Location of 02 sensors - Bank 1 sensor 1 is on the up stream side of the Catalatic Converter. And Bank 1 sensor 2 is on the down stream side of the Catalatic Converter. Bank 2 sensor 1 is on the up stream side of the Catalatic Converter. And Bank 2 sensor 2 is on the down stream side of the Catalatic Converter. ( Bank 1 is the side of the engine that contains #1 Cylinder). Good Luck and have a good XMASS.

Posted on Dec 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

4.6l engine. What is firing order?


Found this firing order.
As far as the sensor, you talking about 02 sensor? Bank one has the number 1 cylinder, bank 2 is the other bank, sensor 1 is the first sensor you come to, in the exhaust.
26115688-ott3b3dnywoy0gcbh2wnhfr2-1-0.jpg

Mar 02, 2016 | 2001 Lincoln Continental

1 Answer

2003 honda civic o2 how to replace And how do i fin out which once is it


Hi Jesus, Im AL the owner of Big As Auto Repair.

If you have a 4 cylinder engine then you will only have two 02 sensors 1/1 is upstream and 1/2 is downstream. Upstream is the one closet to the engine and downstream is the one farther away from the engine.

If you have a six OR eight cylinder engine you will have four 02 Sensors. 1/1 means Bank One Sensor One. 1/1 and Bank one means right bank and right bank means the side with the number 1 spark plug. SO, 1/1 means, "Right Bank" Upstream 02 sensor. 1/2 means, "Right Bank" Downstream 02 sensor.

2/1 means, "Left Bank" Upstream 02 sensor and 2/2 means, "Left Bank" Downstream 02 sensor. Hope this helps and please visit my auto-repair-website at: http://www.bigasautorepair.com/

Nov 26, 2015 | 2003 Honda Civic

1 Answer

2004 mitsubishi endeavor 3.8 p0141 code which points to 02 sensor but where is the bank 1 sensor 2 located


Locate cyl number 1 that is bank #1. Sensor #2 will be located on the portion of the exaust that corresponds to that particular bank after the catalytic convertor. Sensor before the Catalyst is refered to as #1

Sep 28, 2012 | 2004 Mitsubishi Endeavor

1 Answer

My 96 nissian maxima turns off when driving down the road i try to turn the key ,lights in dash on horn blows but will not startcould it be alternater ,or what how does the 02 sensor go by functioning ...


As of 1996,all cars sold in the US were required to have an OBD-II computer interface port.
You may want to go to Advance Auto Parts, AutoZone, or Pep Boys, and get a free read
of the code(s) that you computer may be posting to help with your diagnosis.

The code coming from your vehicle's computer may be one or more of:


P0130 02 Sensor Circuit Malfunction (Bank I Sensor 1)
P0131 02 Sensor Circuit Low Voltage (Bank I Sensor I)
P0132 02 Sensor Circuit High Voltage (Bank I Sensor 1)
P0133 02 Sensor Circuit Slow Response (Bank 1 Sensor 1)
P0134 02 Sensor Circuit No Activity Detected (Bank I Sensor 1)
P0135 02 Sensor Heater Circuit Malfunction (Bank 1 Sensor 1)
P0136 02 Sensor Circuit Malfunction (Bank I Sensor 2)
P0137 02 Sensor Circuit Low Voltage (Bank I Sensor 2)
P0138 02 Sensor Circuit High Voltage (Bank I Sensor 2)
P0139 02 Sensor Circuit Slow Response (Bank 1 Sensor 2)
P0140 02 Sensor Circuit No Activity Detected (Bank 1 Sensor 2)
P0141 02 Sensor Heater Circuit Malfunction (Bank 1 Sensor 2)
P0142 02 Sensor Circuit Malfunction (Bank I Sensor 3)
P0143 02 Sensor Circuit Low Voltage (Bank I Sensor 3)
P0144 02 Sensor Circuit High Voltage (Bank I Sensor 3)
P0145 02 Sensor Circuit Slow Response (Bank 1 Sensor 3)
P0146 02 Sensor Circuit No Activity Detected (Bank I Sensor 3)
P0147 02 Sensor Heater Circuit Malfunction (Bank I Sensor 3)
P0150 02 Sensor Circuit Malfunction (Bank 2 Sensor I)
P0151 02 Sensor Circuit Low Voltage (Bank 2 Sensor I)
P0152 02 Sensor Circuit High Voltage (Bank 2 Sensor 1)
P0153 02 Sensor Circuit Slow Response (Bank 2 Sensor 1)
P0154 02 Sensor Circuit No Activity Detected (Bank 2 Sensor 1)
P0155 02 Sensor Heater Circuit Malfunction (Bank 2 Sensor 1)
P0156 02 Sensor Circuit Malfunction (Bank 2 Sensor 2)
P0157 02 Sensor Circuit Low Voltage (Bank 2 Sensor 2)
P0158 02 Sensor Circuit High Voltage (Bank 2 Sensor 2)
P0159 02 Sensor Circuit Slow Response (Bank 2 Sensor 2)
P0160 02 Sensor Circuit No Activity Detected (Bank 2 Sensor 2)
P0161 02 Sensor Heater Circuit Malfunction (Bank 2 Sensor 2)
P0162 02 Sensor Circuit Malfunction (Bank 2 Sensor 3)
P0163 02 Sensor Circuit Low Voltage (Bank 2 Sensor 3)
P0164 02 Sensor Circuit High Voltage (Bank 2 Sensor 3)
P0165 02 Sensor Circuit Slow Response (Bank 2 Sensor 3)
P0166 02 Sensor Circuit No Activity Detected (Bank 2 Sensor 3)
P0167 02 Sensor Heater Circuit Malfunction (Bank 2 Sensor 3)

Note: "Bank 1" is the side of the engine with cylinder 1. "Bank 2" is the other side.

P0300 - Random/Multiple Cylinder misfire detected
P0301 - Cylinder 1 misfire detected
P0302 - Cylinder 2 misfire detected
P0303 - Cylinder 3 misfire detected
P0304 - Cylinder 4 misfire detected
P0305 - Cylinder 5 misfire detected
P0306 - Cylinder 6 misfire detected
P0307 - Cylinder 7 misfire detected
P0308 - Cylinder 8 misfire detected
P0313 - Misfire detected with low fuel


Maximas with the VE30DE and VQ30DE engines use a distributorless ignition system that is controlled by the Engine Control Module (ECM). The ECM receives a signal from the crankshaft sensor (the CPS - Crankshaft Position Sensor), and processes the signal based on inputs
from other various engine sensors, including the Oxygen sensor.
(this is the role of the O2 sensor in ECM operation).
Then the ECM sends signals to each of the individual coils in the proper firing order.
This system is more efficient than a distributor, and has fewer moving parts. The high voltage coils are directly attached to each spark plug, allowing a higher energy spark within the cylinder. A high energy spark means a faster, more thorough burning of the air/fuel mixture, which produces more power and lower emissions.


SECONDARY SPARK TEST - works for all cars, including Maxima.


1. Remove the spark plug.

2. Install the spark plug to the ignition coil/coil pack, then attach the coil wiring.

3. Ground the plug at a good ground location on the engine.

4. Crank the engine and check for spark.

5. If spark occurs, the ignition system is functioning properly.

6. If no spark exists, test the ignition coil/coil pack, power transistor and related wiring.

----------------------------------------------------------------------------------------------------------------------------
HEI Ignition Spark test - works for all cars, including Maxima.

The next level test you may want to try is a HEI (high energy ignition) spark tester kit. Cost is
about $30 at most auto parts stores. Harbor Freight Tools sells a chinese equivalent for about $16.
Place the spark tester on each of the spark plugs, and watch as the little light in the tester will
light up each time the spark plug is fired by the computer. You can actually see weak or
intermittent sparking as the motor runs - you can tell by the relative strength of the light as
you compare the intensity and duration of the light across all 6 cylinders.

If your problem were the alternator (or its built-in voltage regulator), your battery would not be
getting a proper charge, and you
wouldn't be able to start the car after a drive, since the battery would have been drained during the
drive - normally, the alternator will both charge the battery and run all electrical
features of the car during a drive.

To test your alternator, place your DMM (digital multimeter) across the battery terminals while the
car is running - it should read 13.5VDC to 14.5VDC. With the car off, you can test your battery
voltage with the same DMM - it should read 12.65 VDC (for a fully charged battery).

Alternatively, you can take your car to Advance Auto Parts, AutoZone, or Pep Boys, and they'll
attach their "charging system tester" to your car and give your car a nice test for free.
I do this with my customers' cars just to get that nifty printout of the problem. Its nice
to show a vehicle owner somethng in black & white when I'm recommending a new charging
or ignition system component (some of which can be a bit pricey).

Jul 15, 2011 | 1996 Nissan Maxima

1 Answer

Im getting code P2253 on my 04 Saturn vue with 3.5l V6. Anyway to tell which O2 sensor it is? Thxs Bill


P0804 is the highest OBD-II trouble code.

Here's your Oxygen sensor codes.

P0130 02 Sensor Circuit Malfunction (Bank I Sensor 1)
P0131 02 Sensor Circuit Low Voltage (Bank I Sensor I)
P0132 02 Sensor Circuit High Voltage (Bank I Sensor 1)
P0133 02 Sensor Circuit Slow Response (Bank 1 Sensor 1)
P0134 02 Sensor Circuit No Activity Detected (Bank I Sensor 1)
P0135 02 Sensor Heater Circuit Malfunction (Bank 1 Sensor 1)
P0136 02 Sensor Circuit Malfunction (Bank I Sensor 2)
P0137 02 Sensor Circuit Low Voltage (Bank I Sensor 2)
P0138 02 Sensor Circuit High Voltage (Bank I Sensor 2)
P0139 02 Sensor Circuit Slow Response (Bank 1 Sensor 2)
P0140 02 Sensor Circuit No Activity Detected (Bank 1 Sensor 2)
P0141 02 Sensor Heater Circuit Malfunction (Bank 1 Sensor 2)
P0142 02 Sensor Circuit Malfunction (Bank I Sensor 3)
P0143 02 Sensor Circuit Low Voltage (Bank I Sensor 3)
P0144 02 Sensor Circuit High Voltage (Bank I Sensor 3)
P0145 02 Sensor Circuit Slow Response (Bank 1 Sensor 3)
P0146 02 Sensor Circuit No Activity Detected (Bank I Sensor 3)
P0147 02 Sensor Heater Circuit Malfunction (Bank I Sensor 3)
P0150 02 Sensor Circuit Malfunction (Bank 2 Sensor I)
P0151 02 Sensor Circuit Low Voltage (Bank 2 Sensor I)
P0152 02 Sensor Circuit High Voltage (Bank 2 Sensor 1)
P0153 02 Sensor Circuit Slow Response (Bank 2 Sensor 1)
P0154 02 Sensor Circuit No Activity Detected (Bank 2 Sensor 1)
P0155 02 Sensor Heater Circuit Malfunction (Bank 2 Sensor 1)
P0156 02 Sensor Circuit Malfunction (Bank 2 Sensor 2)
P0157 02 Sensor Circuit Low Voltage (Bank 2 Sensor 2)
P0158 02 Sensor Circuit High Voltage (Bank 2 Sensor 2)
P0159 02 Sensor Circuit Slow Response (Bank 2 Sensor 2)
P0160 02 Sensor Circuit No Activity Detected (Bank 2 Sensor 2)
P0161 02 Sensor Heater Circuit Malfunction (Bank 2 Sensor 2)
P0162 02 Sensor Circuit Malfunction (Bank 2 Sensor 3)
P0163 02 Sensor Circuit Low Voltage (Bank 2 Sensor 3)
P0164 02 Sensor Circuit High Voltage (Bank 2 Sensor 3)
P0165 02 Sensor Circuit Slow Response (Bank 2 Sensor 3)
P0166 02 Sensor Circuit No Activity Detected (Bank 2 Sensor 3)
P0167 02 Sensor Heater Circuit Malfunction (Bank 2 Sensor 3)

Note: "Bank 1" is the side of the engine with cylinder 1. "Bank 2" is the other side.

Jul 03, 2011 | 2004 Saturn VUE

1 Answer

What is a Bank 2 heat sensor and where is it located on a 2004 f150


Bank 1 02 is on the exhaust side that cylinder 1 is on bank 2 would be the other there should be bank 1 sensor one and bank 1 sensor 2 and on the other side it is bank 2 sensor 1 and sensor 2 with that in mind get a firing order from a auto part store bank 2 should be on the driver side sensor 1 is before the cat sensor 2 after the catalytic convertor

Jan 27, 2011 | 2004 Ford F150

2 Answers

I need to know which is the bank 1 02 sensor


Oxygen sensors are always numbered like this:
Bank 1 sensor 1
Bank 2 sensor 1
Bank 1 sensor 2
Bank 2 sensor 2

Some manufacturers use a kind of shorthand that reads different, but means the same thing:
Sensor 1/1 or O2s 1/1
Sensor 2/1 or O2s 2/1
Sensor 1/2 or O2s 1/2
Sensor 2/2 or O2s 2/2

Bank 1 is always the side of the engine where cylinder number 1 is located and, of coarse, Bank 2 is the opposite side.
On a 4 cylinder engine, there is only 1 bank and it is always referred to as Bank 1.

Sensor 1 is always the upstream sensor (The one located BEFORE the catalytic converter)
Sensor 2 is always the downstream sensor (the one that is located AFTER the catalytic converter.

Hope helps (remember to rate this).

Oct 20, 2010 | Ford Explorer Cars & Trucks

Not finding what you are looking for?
1996 Cadillac Seville CA Value Logo

Related Topics:

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...