Question about Toyota Tundra

Open Question

P1130 for Toyota tundra 2000

How to fix p1130 manufacturer controlled ful air metering

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1861 Answers

SOURCE: Toyota Avalon XLS, yr 2000, engine lights on

P0171 is a lean code. Open the hood, and locate the mass air flow sensor. Small black thingy in the intake tube between the air filter box and the engine, held in with 2 small screws. Remove the connector, remove the screws, and remove the sensor. Look into the sensor, you are going to see a couple of wires deep inside it. They will probabaly be "fuzzy" looking. Spray some brake cleaner on the wires until they are nice & clean. This will cure the P0171 code. Then check the air filter; replace it if it is dirty.

P1130 is an air-fuel sensor code, bank one, sensor one. More often than not, when we see this code, we replace the air-fuel sensor. Buy the replacement from you Toyota dealer, because the aftermarket sensors will not send the proper signal to the ECU, and you will be upset for having to buy a second sensor.

P0440 is a leak in the evaporative side of the fuel system; this looks after the fumes of the fuel in the tank. There are several reasons for seeing a P0440, like leaking vacuum lines, faulty fuel cap, rusty fuel filler tube at the cap, etc. This is kind of difficult to rectify without the proper equipment needed to diagnose what & where the actual leak is.
Hope this helps, please consider kind remarks regarding this solution. Thanks.

Posted on Sep 16, 2008

Ad
Scorpedo
  • 111 Answers

SOURCE: 2000 Lexus RX300 6cyl 3L VVT-i "Engine Codes"!

The first and last code are your start and stop so you can ignore them the P1130 and P1150 are your two front oxygen sensors( pre cats ) bank one and two. Depending on your millage it sounds like it is time for a little maintence. Normally they should be changed at or around 60,000 kms

Posted on Dec 12, 2008

  • 30 Answers

SOURCE: code p1130 p0171

P0171- mens the MAF sensor is dirty and needs cleaned. You can get MAF cleaner at your local auto parts store. The MAF is located in the air intake just after the air filter
P1130- is more than likely a result of the previous code. It is in regard to the feul/air mixture ratio. A dirty MAF can cause this code.
Also, if you are using an aftermarket oiled air filter, it would be the cause of the P0171 code.

Posted on Aug 08, 2009

  • 1 Answer

SOURCE: what does computer code p1131 manufacturing control fuel air metering mean

Code p1131 manufacturer control fuel air metering, on a 2003 Ford Taurus. Where is part? Is there an easy way to see if it can be fixed without buying the expensive part?

Posted on Sep 01, 2009

  • 524 Answers

SOURCE: how do I adjust the idle on a 2000 toyota tundra

This is all controlled by a computer, you are going to need to take it to a dealer, OR you can buy a tuner that will also control idle

Posted on Apr 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

P1130 CODE FOR 2000 TOYOTA SIENNA


The air/fuel ratio sensor has gone bad (basically the O2 sensor). The code P1130 is Bank 1 Sensor 1.
Sensor 1 is before the catalytic converter coming off the exhaust manifold. Bank 1 is which ever side cylinder 1 is on your engine. In this case its a sideways engine and its closest to the firewall.

May 01, 2014 | 2000 Toyota Sienna

2 Answers

P1130, P1320, P0172


(171,172) replace MAF , replace air filter with o.e. type (1130) Check vac. lines and connectors to vac. solenoids
(1320) ignition coil primary failure, if all connections are good, replace all the coils

Jan 11, 2014 | 2001 Nissan Pathfinder

1 Answer

What does the code p1130 mean?


code p1130 refers to heated oxygen sensor--LH front--range/ performance malfunction===causes--wiring--oxygen sensor--air induction system--fuel pressure---injector/s ECM. Personally I would be suspicious of the oxygen sensor first.

Jul 21, 2013 | 2002 Toyota Camry

1 Answer

How do i fix p1130 AND P 1440 code on my 2000 Nissan maxima? It takes about 5-6 minutes to crank up.


P1130 Swirl Control Valve Circuit Malfunction - With Automatic Transmission Possible Causes
  • Check for air leaks in the Air Induction system (e.g., in the intake manifold)
  • Check for leaks or looseness in hoses and tubes between the intake manifold, vacuum tank and swirl control valve actuator
  • Check for leaks or looseness in the hoses between the air cleaner assembly and the swirl control valve vacuum check valve
  • Crankshaft position sensor (REF) signal problem
  • MAF sensor has failed (it may be dirty or contaminated)
  • One-way check valve has failed
  • Swirl control valve actuator has failed (it may be damaged or sticking)
  • Swirl control valve control connector is damaged (check pins for damage)
  • Swirl control valve circuit is open, shorted to ground or shorted to voltage
  • Swirl control valve has failed
  • PCM has failed
  • Throttle position sensor has failed
  • Vacuum tank has failed

P1440...EVAP Control System (Small Leak)
Check your fuel cap & reset code,

Good luck, hope this helps,,,

Jul 15, 2011 | 2000 Nissan Maxima

2 Answers

Enciendo el auto y me encinde la luz de check y dice que es el codigo p1130


DTC P1130 - Swirl Control Valve Control Solenoid Valve

Otros detalles acerca de los codigos de falla los puede encontrar en este enlace: manual_detalle.php?manual_id=101

Buena suerte.

May 26, 2011 | 1996 Nissan Pickup

1 Answer

I have a 1998 ford contour that has codes p1130 and p1131 on it what could be the problem. the check engine light is on


H40 DTCs P1131, P1132, P1151 AND P1152: UPSTREAM HO2S NOT SWITCHING. DTC P1130: FUEL SYSTEM NOT SWITCHING AT FUEL TRIM (RICH OR LEAN)
    Diagnostic Trouble Codes (DTCs) P1131 bank 1 (Cylinder 1) and P1151 bank 2 indicate the fuel/air ratio is correcting rich for an overly lean condition. The HO2S voltage is less than 0.45 volt. DTCs P1132 bank 1 (Cylinder 1) and P1152 bank 2 indicate the fuel/air ratio is correcting lean for an overly rich condition. The HO2S voltage is greater than 0.45 volt.
    DTC P1130 and P1150 indicate the fuel control system has reached maximum compensation for a lean or rich condition and the HO2S is not switching.
    DTC/HO2S Reference List
    • HO2S-11 = DTCs P1131, P1132 and P1130
    • HO2S-21 = DTCs P1151, P1152 and P1150
    Possible causes:
    Fuel system
    • Excessive fuel pressure.
    • Leaking fuel injector(s).
    • Leaking fuel pressure regulator.
    • Low fuel pressure or running out of fuel.
    • Contaminated fuel injector(s)
    • Vapor recovery system
    Induction system
    • Air leaks after the MAF.
    • Vacuum leaks (vacuum lines and gaskets).
    • Restricted air inlet.
    • PCV system.
    • Improperly seated engine oil dipstick.
    EGR System
    • Leaking gasket.
    • Stuck open EGR valve.
    • Leaking diaphragm.
    Base engine
    • Oil overfill.
    • Cam timing.
    • Cylinder compression.
    • Exhaust leaks before or near the HO2Ss.
  • Check intake air system for leaks, obstructions and damage.
  • Check air cleaner element, air cleaner housing for blockage.
  • Verify integrity of the PCV system.
  • Check for vacuum leaks.

Feb 12, 2011 | Ford Contour Cars & Trucks

1 Answer

Engine code p1130


The code P01130 is your swirl control valve ,in intake manifold, helps air flow at idle for better combustion in cylinders helps emissions!
If it runs ok that's your call to fix it. could affect performance!

Sep 23, 2010 | 1996 Nissan Pickup

1 Answer

I have a 2000 Camry - 6 cylinder with about 180,000 miles on it. The Check engine light came on and it showed three codes - P0125, P1130 and P1135 - We put in a new thermostat - and still the check engine...


Was the computer reset after the thermostat was replaced?? If not, it must be reset to clear prior codes. as for the p1130/1135, they are related here is some info>>>>http://www.engine-light-help.com/toyota-engine-light.html

Mar 11, 2010 | 2000 Toyota Camry

1 Answer

Manufacturing control fuel air metering


my 2000 ford escort se is bucking & jerking like a horse,the muffler shop says it's the manufacture fuel air control metering,where is it located & how much will it cost?.where would i go 2 have it fixed.or can my husband fix it?

Feb 22, 2010 | 1999 Ford Expedition

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...