Question about Dodge Durango

Open Question

P0335 p0340 - Durango Dodge Cars & Trucks

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: i have a p0335 and p0340 and replaced cam sensor

replace the crank position sensor..if that doesnt solve it, could be in the ignition system

Posted on Jan 14, 2010

Ad
  • 251 Answers

SOURCE: p0340

The vehicle until warm runs off a different set of parameters for the computer as far as timing and fuel are concerned. Temp is not a problem at 200... and it is normal for the oil pressure to lower once warm. ( as long as you have 10 psi oil pressure for every 1,000 rpm's you are ok.)

The two codes cam/crank sensor are timing related related. So I would suspect something that deals with both sensors,Timing chain maybe?This particular engine has a problem with chewing up timing chains. If you find this to be the problem i recommend using factory GM replacement parts. I have had to re-do several that i tried to use aftermarket parts on. The only other thing that comes to mind , dealing with the drive ability, is the fuel pressure. These vehicles are sensitive in the fuel pressure area, but this should not make the light on the dash come on. You may have more than one issue. The other part of the vehicle that deals with timing is the ECM. If you have access to a scan tool with data stream on it , you can look and see if the ECM is receiving a signal.

Posted on Jun 07, 2011

mensaman151
  • 377 Answers

SOURCE: Stall Driving, Crank and no start codes p0127

it is in your firing distribution and or ignition coil pack on any engine when you get these codes ..if the vehicle is showing codes and it is still running say smooth ,,it will not be for long ,,those lights come on generally before these components go out

Posted on Oct 18, 2013

Testimonial: "I have the solution now. This engine is EXTREMELY poorly designed. With all the problems Toyota and Honda had in the 80s I would have never have thought they would use a rubber band to spin the camshaft. Well, they do and with 110k on this truck, the rubber band stretched. So it needs an Engine!!! Technically a valve job. But, I priced it both ways and it is a lot cheaper just to replace the engine in it. I found an engine with 100k on it for $600. Anyway, thanks and sorry to waste everyones time!!!!!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Stall Driving, Crank and no start codes p0127 p0335 p0340


it is in your firing distribution and or ignition coil pack on any engine when you get these codes ..if the vehicle is showing codes and it is still running say smooth ,,it will not be for long ,,those lights come on generally before these components go out

Oct 18, 2013 | 2004 Toyota Tundra

1 Answer

2002 PT Cruiser. Vehicle shut down while driving. Received P0340 Trouble code..No camshaft position sensor signal at pcm. I replaced Position Camshaft Sensor, book suggests life on these 5-10 years, It...


This could be related to a loose camshaft drive belt. If you have slack in the belt the camshaft will rebound on over run causing the P0340. It can also be a Crackshaft sensor problem too.(P0335) Hope this helps...

Mar 06, 2011 | 2003 Chrysler PT Cruiser

1 Answer

2002 Mitsubishi Galant 2.4 with repeating error codes P0335,P0340


Check your timing marks , you may have jump the tooth on a timing belt.

May 10, 2010 | Mitsubishi Galant Cars & Trucks

1 Answer

My cadillac deville has the following engine codes when hooed up: P0106, P0121, P0171, P0174, P0335, P0340, P0385, P0442, P0506, P0506, P0507, P0601.


click on the below links for code details.
P0106

P0121

P0171

P0174


P0335


P0340

P0385

P0442

P0506

P0507

P0601.

all of the above codes seem to have a common cause, they all list a bad ecm (computer) as being a cause, and the last code P0601 points specifically to a bad computer. sorry for the bad news, hope this helps.

Dec 06, 2009 | 2000 Cadillac DeVille

1 Answer

I have a p0335 and p0340 and replaced cam sensor


replace the crank position sensor..if that doesnt solve it, could be in the ignition system

Nov 28, 2009 | Mitsubishi Eclipse Cars & Trucks

2 Answers

Crankshaft Position Sensor Error P0335 recurred after r&r


In the kit there are two sensor that look identical. The one for the crankshaft has a white paint mark on it near the bolt hole. Make sure that it is in the right location.

Jul 25, 2009 | 2003 Nissan Altima

2 Answers

I have a 2000 Mitsu. Galant. Trouble codes p0335 and p0340 for cam and crank sensors.Are there any common problems?


Hi, I found a couple of good articles on those codes. Rather than just copy and paste here are the links:

P0335 - Crankshaft Position Sensor Electrical Error
http://www.bba-reman.com/content.aspx?content=NEXT_DTC_P0335

P0340 - Camshaft Positio Sensor Circuit Malfunction
http://www.obd-codes.com/p0340

Jan 03, 2009 | Mitsubishi Galant Cars & Trucks

1 Answer

Engine turns but won't start


No.: TSB-07-11-001
DATE: January, 2007
MODEL: 2002-07 Lancer 2.0L
SUBJECT:
HARD TO START ENGINE DTC P0340 (and P0335)

PURPOSE
The engine may be hard or impossible to start and MFI DTC P0335 and possibly P0340 may be stored due to abnormal wear to the camshaft position sensor support. Oil grooves have been added to the camshaft position sensor support to improve lubrication

Nov 04, 2008 | 2003 Mitsubishi Lancer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...