Question about 2002 Mazda B-Series

Open Question

Fuel pump adjustment screw mazda b2500 turbo diesel

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76109 Answers

SOURCE: Looking for the fuel pump shut-off switch for 1998 Mazda Pickup

The fuel pump shut-off switch is
located in the passenger’s foot well,
behind the kick panel. There is an access hole.

Posted on Mar 27, 2009

Ad
  • 1 Answer

SOURCE: b2500 turbo diesel fuel pump diagram

courier%20injector%20pump%20inlet%20filter.jpg Undo the fuel inlet Banjo bolt and carefully fish with a piece of wire bent at the end (as pictured) and fish out the filter (under the spring) wash and replace. Can be very fiddly, so patience is a must.a2cb1b7.jpgecc55b3.jpg

Posted on Dec 01, 2009

  • 608 Answers

SOURCE: mazda 6 2o diesel replaced turbo new unit same

There is a oil drain return from the turbo charger to the sump. If the sump oil level covers the outlet into the sump, oil will build excess pressure tin the turbo causing the sealing rings to leak oil in to the intake manifold. This would cause smokey exhaust and loss of oil. Try this. Drain the sump completely, refill with the exact quantity of oil to Mazda spec. Dip the oil and if the new oil level is lower than the full mark on the dipstick, you have found the cause of the problem. Mark this new level with a scriber or file and fill only to this new level. Hope this is the solution.

Posted on Mar 23, 2010

  • 280 Answers

SOURCE: mazda 2000 B2500 main, rod+cil head bolt torque

call your local auto zone-they can give them to you

Posted on Mar 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi I have put a new turbo on my mazda 6 diesel. There is no oil leak there is just loss of power as if there is no turbo. It's as if max speed I can get upto is 90. Part from that there car runs g


Since the power generated by the turbo depends on the volume of combustion gas generated, look into your fuel delivery system. Your engine might not be receiving the required amount of fuel. Check your fuel pump, filter, injectors, and lines.

Oct 28, 2012 | 2007 Mazda 6

1 Answer

Timing the fuel injection pump


What is this, Mazda's do not have diesels in the USA anymore.

May 28, 2012 | 1999 Mazda B2500

1 Answer

2000 Mazda Drifter 2.5 Turbo Diesel, exhaust manifold torque settings for nuts.


Mazda B2200, B2500 and B2600 (6th Generation).

In model year 1998, Mazda B series renews its own international markets. Production at the plant AutoAlliance Thailand began in May 1998. This model is also sold as the Ford Ranger in Europe and Asia, and the Ford Courier in Australia and New Zealand. Production started this year in the factories of companies AutoAlliance Thailand and Ford Motor Philippines. Versions CKD are also assembled in South Africa, Ecuador and Colombia.

The van is sold in over 130 countries under a variety of names. Along with the emblems of Fighter and Ranger in Southeast Asia (except Singapore, which served as the flagship models Proceed Japan), was sold as the Mazda Bounty and Ford Courier in New Zealand, Mazda Bravo in Australia, and Mazda Drifter in South Africa.

Engine options:
2.2 L 2.2 L (2.184 cc) 85 hp (63 kW)
2.5 L (1.998 cc) turbo diesel 118 hp (88 kW)
2.6 L (2.606 cc) 121 hp (90 kW)


zjlimited_1152.jpg

Fig. Tighten the exhaust manifold bolts in 2 stages

To install:

  1. Clean the mating surfaces on the exhaust manifold and the cylinder head.
  2. Install a new gasket and the exhaust manifold. Torque the bolts in sequence as follows:
    1. 16 ft. lbs. (23 Nm).
    2. 59 ft. lbs. (80 Nm).

Hope helps.

May 01, 2011 | Mazda B2600 Cars & Trucks

2 Answers

Problem starting my mazda bt50 3.0 turbo Diesel 2007. had new injectors 6 months ago


Hi I have a problem, to start my 2010 3 liter mazda bt50.
I change the fuel pump but still the problem didn't solve

Feb 22, 2011 | 2007 Mazda B Series

1 Answer

B2500 turbo diesel fuel pump diagram, motor want rev past 2000 rpm starving of fuel ,has fuel pump got am internal filter, i have changed fuel filter.


courier%20injector%20pump%20inlet%20filter.jpg Undo the fuel inlet Banjo bolt and carefully fish with a piece of wire bent at the end (as pictured) and fish out the filter (under the spring) wash and replace. Can be very fiddly, so patience is a must.a2cb1b7.jpgecc55b3.jpg

Nov 17, 2009 | 1997 Mazda B-Series

2 Answers

Mazda bravo blowing white smoke


blowing white smoke is almost always a symptom of an engine coolant leak at the cylinder head gasket. remove each spark plug and look for a dis-colored plug to find which cylinder is leaking.

May 26, 2008 | 2007 Mazda B Series

Not finding what you are looking for?
2002 Mazda B-Series Logo

Related Topics:

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...