Question about Cars & Trucks

Open Question

How to set the pins for my key on a locksmart LC65349?

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I program my new keys that came with locksmart ignition lock cylinder switch from autozone is there a way I can do it my self on my 06 Honda civic


you can't do it!either local locksmith with correct tool or the DEALER.and you will need to take the car with you on a tow truck!it ain't gonna start,until they program it to your car with a special scan tool!

Oct 31, 2015 | 2006 Honda Civic 1.8

1 Answer

Can you help me with the restart system on i installed a locksmart ignition switch on my 2002chey malibu part#LC63730


what is a RESTART
do you mean Aftermarket remote start system (hacks)?
if yes, did you loose the origional instructions?

May 02, 2014 | Cars & Trucks

1 Answer

Car will not start or even turn over


If it has the "locksmart" PAT(passive Anti Theft) option,there is a chip in the black plastic "head" of the key,that is mated to a reciever in the steering colum, a magnet would most likely mess the system up.
It kills the fuel,hence the no start. If you have another key,try that,if not ,take the key off the ring and try it. Odd thing about the dash lights,but the key switch "talks" to the computers so maybe. My best thoughts on your problem. let me know.

Nov 14, 2013 | 2005 Lincoln Town Car

1 Answer

What are the timing marks for a 1996 toyota camry, 2.2


2S-ELC, 3S-FE and 5S-FE Engines

When install,
align the crankshaft pulley set key with the pulley key groove. Install the pulley. Tighten the pulley bolt to 80 ft. lbs. (108 Nm).

On 2S-ELC engines, turn the crankshaft pulley and align the 0 mark on the lower (No. 1) timing belt cover.
Align the camshaft knock pin with the matchmarks on the oil seal retainer.

On 2S-ELC/USA engines, align the knock pin with the pin hole on the timing pulley E mark side. On 2S-ELC/Canadian engines, align the knock pin with the pin hole on the timing pulley.

On 3S-FE and 5S-FE engines, align the knock pin with the groove of the pulley, and slide the pulley onto the camshaft with the plate washer and set bolt.



Apr 29, 2011 | 1996 Toyota Camry

1 Answer

How do i remove an ignition lock cylinder in a 96 taurus without a key...the car doesnot have any antitheft measures


Hello! Turn the key to ACC...Insert a 1/8" drill bit into the hole at the top of the cylinder housing...Depress the retaining pin and pull lock out...To install...Set the new lock to ACC...Depress retaining pin...Insert lock...Turn the key to off to release the pin...See photo...Guru...Saailer...


saailer_84.gif

Mar 04, 2011 | 1996 Ford Taurus

1 Answer

I WANT TO CHANGE THE KEY BARRELS OF MY 1996 ESCORT MK6 18 DESIEL. IF POSSIBLE I DO NOT WANT TO USE FORD'S KEY BARRELS BECAUSE THEY WEAR ALOT. CAN I FIT ANOTHER BRAND THAT ARE MORE DURABLE?


There are a couple different brand names of aftermarket key lock cylinders. LOCKSMART has one for auto transmission and for manual transmission. Part Number LC65620 For the auto, Part Number LC65580 for manual. These are available through Autozone and O'Reilly's. BORG WARNER has makes these also The part numbers are the same. (These are avilable through O'Reilly's and Advance Auto. It may be helpful to let you know that these are probably all manufactured by the same manufacturer that makes the MOTORCRAFT (Ford) cylinders. They just sell to different distributors, who put their names on them.

Note that these are the part numbers for the key and tumbler assembly only. The complete ignition switch assembly ( tumbler, barrel, switch ) is also available through these same suppliers.

Feb 03, 2011 | 1998 Ford Escort

2 Answers

I need to take out old ignition lock cylinder without key on 1989 toyota camry le -lost keys-bought locksmart replacement but it says old has to be in acc position to remove-


This is what the tech manual says.....

Ignition Lock/Switch REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable. If equipped with an air bag, wait at least 90 seconds before working on the vehicle. CAUTION
    Some models covered by this manual may be equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, disable the SRS, as described in Section 6.
  2. Remove the lower steering column cover. Unfasten the ignition switch connector under the instrument panel.
  3. Remove the screws which secure the upper and lower halves of the steering column cover.
  4. Turn the lock cylinder to the ACC position with the ignition key.
  5. Push the lock cylinder stop in with a small, round object (cotter pin, punch, etc.). NOTE: On some vehicles, it may be necessary to remove the steering wheel and combination switch first.
  6. Withdraw the lock cylinder from the lock housing while depressing the stop tab.
  7. To remove the ignition switch, unfasten its securing screws and withdraw the switch from the lock housing. To install:
  8. Align the locking cam with the hole in the ignition switch and insert the switch into the lock housing.
  9. Secure the switch with its screw(s).
  10. Make sure both the lock cylinder and column lock are in the ACC position. Slide the cylinder into the lock housing until the stop tab engages the hole in the lock.
  11. Install the steering column covers and connect the ignition switch wiring.
  12. Connect the negative battery cable.

Jul 26, 2009 | 1991 Lincoln Town Car

1 Answer

I need instructions on how to put a locksmart switch ingnition


this not something that a back-yard mechanic should tackle

Mar 15, 2009 | 2002 Ford SVT Focus

1 Answer

I need instructions on how to put a locksmart switch ingnition


Removal
  1. Disconnect battery ground cable. Remove the steering column shroud by removing the four or five self-tapping screws. Remove tilt lever (if so equipped).
  1. Remove instrument panel lower steering column cover.
  1. Disconnect the ignition switch electrical connector.
  1. Rotate ignition key lock cylinder to the RUN position.
  1. Remove the two screws retaining ignition switch.
  1. Disengage the ignition switch from the actuator.
Installation
  1. Adjust the ignition switch by sliding the carrier to the switch RUN position. NOTE: A new replacement switch assembly will be set in the RUN position as received.
  1. Check to ensure that the ignition key lock cylinder is in the RUN position. The RUN position is achieved by rotating the key lock cylinder approximately 90 degrees from the LOCK position.
  1. Install the ignition switch into the actuator. It may be necessary to move the switch slightly back and forth to align the switch mounting holes with the column lock housing threaded holes.
  1. Install retaining screws. Tighten to 5.6-7.9 Nm (50-69 lb-in).
  1. Connect electrical connector to ignition switch.
  1. Connect battery ground cable. Check ignition switch for proper function, including START and ACC positions. Also, make certain that the column is locked in the LOCK position.
  1. Install instrument panel lower steering column cover.
  1. Install the steering column trim shrouds and tilt lever (if so equipped).

Feb 26, 2009 | 1991 Lincoln Town Car

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

141 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...