Question about 2000 Oldsmobile Silhouette

Open Question

Where are the fuse for the air compressor pump for rear shocks and when does it come on & off also the reak air pump inside car in the real panel, for 2000 Ols Silhouette,thanks for any help !!

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: REAR DEFOGGER NOT WORKING 2000 OLS ALERO

There's a junction box behind passenger rear door that has 2 wires that are joined from the front and control the rear defroster and radio antenna.

Posted on Mar 24, 2009

Ad
  • 401 Answers

SOURCE: air ride problems '99 Silhouette

u can't change the just the valve u can change the compressor head but still costly the only other way would be and easier buy a used one

Posted on May 03, 2009

Molson02536
  • 3854 Answers

SOURCE: 2003 Olds Silhoutte Air Shocks and Compressor - not working

The load leveling shock will not work if there is an issue with the compressor. If you buy the sir shock's, your going to have to address the compressor issue to even have the air shocks level the Silhouette. Once you have the compressor issue addressed, the shocks it's self is simple enough to replace that you can do it with common tools to save you some money. My wife has a Montana and we had the same problem, since we do not tow and really never hold that much weight. We replaced the rear shocks with Monroe Reflex Shocks, Found the van to be much more sturdy then the air shocks ever were and the good thing about them is there were lift time replacement at Parts Source. Regardless on which shocks your going to use, it's a good rule to replace both sides at the same time. The only difference in to reinstalling the air shocks is you need to reattach the air lines to the shocks and that's simple as removing the shocks it self. The shocks are only held on by two bolts,  one on top and one on bottom and should only take about 20 min each side to do since you have to jack the car up and remove the wheel for room, but you can remove the shocks it self without removing the wheel, it's your preference. Good luck and keep me posted, be glad to answer any questions you may have. 

Posted on Aug 11, 2009

  • 615 Answers

SOURCE: 2003 Olds Silhouette air compressor won't shut off

The simple solution is to pull the fuse for the compressor.

If you want this fixed, you most likely have a leak and will need to find and fix it. The compressor may also be rebuilding. Probably not going to be worth putting the money into fixing.

Posted on Oct 17, 2009

  • 30 Answers

SOURCE: 1999 Olds Silhouette -- Problem -

In your case, there a lot of meaning about ABS light problem. But the sulotion is go to the nearest auto parts or autozone, they scan your car for free of chage and they will give you the obd diagnose code and they can also look up on their computer to find out what is the real problem... best of luck..

Ginskie.

Posted on Sep 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The air suspension on our 2000 Lincoln navigator seems not to be working right how can we find out what is causing this can we still drive it with this going on?


Ford Air Ride Rear Suspension Down Diagnosis & Fix ...

? 9:57
https://www.youtube.com/watch?v=wfh7n17hvN8
Feb 24, 2014 - Uploaded by FordTechMakuloco
Ford Air Ride Rear Suspension Down Diagnosis & Fix ... why theair ride compressor is not turning on and pumping up the air ridesuspension on your truck. ... Ford Expedition & Lincoln Navigator Air Ride C1725 Common Faults ... 2000 Ford Expedition - Replacing the rear shocks with load leveling shocks ...

2003 Lincoln Navigator air suspension fix(3) - YouTube

? 3:41
https://www.youtube.com/watch?v=MhWlcYycny4

Dec 25, 2015 | Lincoln Cars & Trucks

1 Answer

Rear air shocks


In the underhood fues box or just disconnect the power to the compressor. You will have to live with a ride control warning light on though.

Mar 18, 2014 | 2005 Chevrolet Venture

1 Answer

2001 Ford Expedition F150 - the rear end of my car is sagging to the right. The leveling pump that I normally hear at the front end is still trying to pump. Any idea where I should start looking first ? ...


You could check for leaking hoses to the shocks
I would replace the 2 rear air shocks with conventional
ones & pull out the fuse for the compressor

Jul 28, 2013 | Cars & Trucks

1 Answer

What does the "leveling" light in the dash mean in my 2000 cadillac catera. why is it on and how do i fix it. put new rear shocks in it and now it stays on all the time.


What the leveling system is is basically a height sensor for the rear height, air shocks, an air compressor and air lines. What happens is the height sensor knows what is considered a normal ride height. When people or items are added at the rear seat or trunk the vehicle sits lower. The air compressor will turn on and attempt to pump up the air shocks to raise the height to normal again so the rear end doesn't bottom out.

What can happen is the compressor fails to turn on due to a blown fuse, faulty compressor or defective height sensor. If the compressor turns on the shocks might not be able to pump up due to a line leak or air shock leak.

If you are able to look at the lines or shocks you might find a problem. Otherwise going to your mechanic and have him/her inspect the system to see what the problem might be and then deside if you want to fix it or have them do the repair. Because the light turns on periodically and goes out I would suspect a leak somewhere.

Sep 05, 2010 | 2000 Cadillac Catera

1 Answer

My air shocks are down and i don;t know what fuse to look for


the fuse is it the right front relay/fuse box, 60 amps I think. Most likely the shocks leak, then the pump runs too much to keep them up, then the pump burns up and blows the fuse. There are companies that make a shock for the rear to delete the air ride, the air ride can cost a lot to get running again. shocks and compressor.

Aug 26, 2010 | 1996 Lincoln Continental

1 Answer

Where is the a.i.r. pump located



The air pump for the secondary air system (emission control device) is located under the battery. If you do replace it, replace the check valve too, it is on top of the exhaust manifold and connected to the pump with a hose. The check valve fails and ruins the pump. Source(s): http://repairpal.com/volvo-850-1997/comm…
http://repairpal.com/air-pump-check-valv…
http://repairpal.com/air-pump

OR


I think they are talking about the pump to provide vacuum to the climate control when the turbo is putting boost in the intake manifold. The vacuum can come from an electric pump or from an engine driven pump, something like an old engine driven fuel pump. I needed an electric pump for my 765T, and all the wrecking yards wanted to sell me the engine driven form. (A new one was $500, and it wasn't that important to me.)

An engine that takes the engine driven pump will have a hole in it while the others will not have a hole. Source(s): 35 years maintaining my own cars, including 17 years with a 1985 765T


OR



Rear Suspension Leveling Air Compressor
RH front of vehicle, attached beneath the fascia

Rear Suspension Leveling Air Compressor Relay K19
Lower I/P, to the RH side of the steering column, on the relay box


Automatic Level Control System Operation Check
Support the rear wheels or support the rear lower control arms when certain tests require raising the vehicle on a hoist. Use two additional jack stands in order to support the rear lower control arms in the normal curb weight position when a frame type hoist is used. Refer to Trim Height Specifications in Suspension General Diagnosis.

Refer to ALC Suspension System Check for electrical troubleshooting of the Automatic Level Control (ALC) system, or if DTC's are present.

Diagnosing Leveling Complaints Without DTCs Present Procedure
Perform the following preliminary inspections before performing the system performance test:

Inspect the ignition (pin A & pin H) at the ALC sensor connector.
Ensure that the ignition (pin A & pin H) at the ALC sensor connector connection is secure.
Inspect the ground (pin E) at the ALC sensor connector.
Ensure that the ground (pin E) at the ALC sensor connector connection is secure.
Inspect the ALC sensor link.
Ensure that the ALC sensor link is properly secured to the actuator arm.
Inspect the ALC sensor actuator arm for damage.
ALC Diagnosis Table Step
Action
Value(s)
Yes
No

1
Has the ALC compressor assembly and the air tube been replaced?
--
Go to Step 7
Go to Step 2

2
Raise and support the vehicle. Lifting and Jacking the Vehicle in General Information.
Inspect the air tubes running from the ALC compressor to both rear shock absorbers.
Inspect the air tube connection at the ALC air dryer.
Are the air tubes damaged and/or disconnected?
--
Go to Step 13
Go to Step 3

3
Squeeze the left rear shock absorber in the middle of the air sleeve.

Did the air sleeve slightly compress?
--
Go to Step 5
Go to Step 4

4
Operate the ALC system for 60 seconds.
Test the air tube-to-air dryer connection for leaks using a soap bubble solution.
Is a leak evident?
--
Go to Step 20
Go to Step 5

5
Disconnect the air tube from the ALC dryer.
Connect the Pressure Gauge to the ALC dryer.
Close the toggle valve on the Pressure Gauge .
Operate the ALC compressor.
Did the pressure build to the specified value?
80 psi
Go to Step 6
Go to Step 10

6
Shut off the compressor when the pressure reaches 80 psi.
Monitor the gauge for 1 minute.
Did the pressure leak down?
--
Go to Step 10
Go to Step 7

7
Connect the Pressure Gauge to the right rear shock absorber. Ensure that the toggle valve on the Pressure Gauge is away from the shock absorber.
Close the toggle valve.
Pressurize the shock absorber at the toggle valve on the Pressure Gauge to 80 psi.
Monitor the gauge for 1 minute.
Did the system leak down?
--
Go to Step 11
Go to Step 8

8
Use the toggle valve on the Pressure Gauge in order to slowly release the air pressure.
Disconnect the Pressure Gauge from the right rear shock absorber.
Connect the Pressure Gauge to the left rear shock absorber.
Pressurize the Pressure Gauge to 80 psi.
Monitor the gauge for 1 minute.
Did the pressure leak down?
--
Go to Step 12
Go to Step 9

9
Use the toggle valve on the Pressure Gauge in order to slowly release the air pressure.
Disconnect the Pressure Gauge from the left rear shock absorber.
Connect the Pressure Gauge , inline, at the tee near the rear of the vehicle.
Reconnect the air tube to the ALC dryer.
Open the toggle valve on thePressure Gauge .
Using shop air, pressurize the system to 80 psi at the service connection of the Pressure Gauge .
Monitor the pressure gauge for 1 minute.
Did the pressure leak down?
--
Go to Step 14
Go to Step 20

10
Replace the following components:

• Replace the ALC compressor. Refer to Air Compressor Replacement .

• Replace the air tube. Refer to Air Tube Replacement .

Are the replacements complete?
--
Go to Step 20
--

11
Slowly open the toggle valve on the Pressure Gauge in order to relieve the air pressure.
Replace the right rear shock absorber. Refer to Shock Absorber Replacement in Rear Suspension.
Reconnect all of the air tube connections.
Is the shock absorber replaced, and are all of the air tube connections reconnected?
--
Go to Step 20
--

12
Slowly open the toggle valve on the Pressure Gauge in order to relieve the air pressure.
Replace the left rear shock absorber. Refer to Shock Absorber Replacement in Rear Suspension.
Reconnect all of the air tube connections.
Is the shock absorber replaced, and are all of the air tube connections reconnected?
--
Go to Step 20
--

13
Are any of the air tubes damaged?
--
Go to Step 14
Go to Step 18

14
Replace the air tube that runs from the air dryer to the two rear shock absorbers.

Is the replacement complete?
--
Go to Step 15
--

15
Remove the ALC air dryer from the compressor assembly.
Shake the ALC air dryer with the head connection down.
Did water/moisture come out of the ALC air dryer when the dryer was shaken?
--
Go to Step 16
Go to Step 17

16
Replace the ALC air dryer. Refer to Automatic Level Control Air Dryer Replacement .

Is the replacement complete?
--
Go to Step 17
--

17
Replace the air compressor head. Refer to Automatic Level Control Air Compressor Head Replacement .

Is the replacement complete?
--
Go to Step 18
--

18
Install the ALC compressor on the vehicle.
Reconnect all of the air tube connections.
Is the ALC compressor reinstalled, and are all of the air tube connections reconnected?
--
Go to Step 20
--

19
Repair the air tube-to-air dryer connection leak.

Is the repair complete?
--
Go to Step 20
--

20
Reconnect all of the connectors that were disconnected.
Reconnect all of the components that were removed.
Clear all of the codes with the ignition ON and with the engine OFF.
Wait at least 5 minutes.
Is the rear of the vehicle trim level?
--
System OK
--






Aug 04, 2010 | 1998 Cadillac Catera

2 Answers

Rear air ride is flat on 95 deville....what do i


the first thing is the fuses. i've seen many of these that the rear air shocks are bad but customer doesnt know and the pump runs until it burns out,after checking the fuses start the car and listen under the hood for the pump to turn on, if pump turns on then check shocks for leaks, also you would have to make sure the pump is producing air as it runs and the last thing is the level sensor located under the rear of car.

Jul 13, 2010 | 1995 Cadillac DeVille

2 Answers

I have 94'crown vic with rear air ride suspension problems. The back end won't rise. Any help is appreciated.


Start by checking the fuses for the air compressor for the rear suspension. these will be listed in your owners manual. Failing this it could be the compressor motor or wiring to the motor, unless you can hear the compressor working. If the compressor is running but not adjusting the back of the car then you have an air leak in one of the shocks or air lines.
if you find it is a fuse, also listen for the compressor motor running and an air leak, if the system is running constantly to make up for a leak , that may be what blew the fuse.

Hope this helps
Ed

Mar 29, 2010 | 1994 Ford Crown Victoria

3 Answers

Air ride is not working


were is the fuse located for the air ride

Jun 09, 2009 | 1999 Cadillac DeVille

3 Answers

Service ride control


The fuse is called RTD 30 amp under the hoodfuse box. That is for the Air Compressor.

Parts.com has the best price for:

Rear Suspension:
Shock W/auto level control - 1500 series

and under
electrical:
then ride control components
then compressor

May 03, 2009 | 2006 GMC Yukon Xl Denali

Not finding what you are looking for?
2000 Oldsmobile Silhouette Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8548 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...