Question about Cars & Trucks

1 Answer

Compass problem since i bought this car july 2013 it gives me hell, i only drive the car two weeks then the is stuck up until now its still giveng me problem , ecery time they jumpstart and they gave back to so now i am sick i tired i must i do, i am not an expert but the way i see the problem its a factory fault pls help what tom do with this dealer because they got their mnoney i am sitting with the problem

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 2,687 Answers

Has the warranty expired ?

Posted on Aug 12, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 51 Answers

SOURCE: grinding noise front end when

Do you have aftermarket rims? If the rims rub against an outer tie rod, it will destroy tires. Any kind of suspension modification can cause this also.

chris

Posted on Aug 01, 2008

  • 1861 Answers

SOURCE: 2006 toyota solara, alarm keeps going off

Those cars have a frequency sensor that is attuned to the exact sound frequency of breaking glass. Are there any noises nearby that resemble glass shattering? Wind chimes? Any type of extraneous noise at the freq of glass breakage will set off the alarm.

Posted on Feb 27, 2009

  • 30 Answers

SOURCE: Ford Focus Engine System Fault warning light

yes there is a know problem with the fuel system. fuel pump breaks down, empty your fuel filter into a bowl and check for metalic, if you have this in the filter your pump is F..... along with all the other common rail stuff. expensive job... error codes though, i find that hard to believe, fuel pressure faults will occur, i think you garage does not know what to do. or does not want to tell you the cost of the job and he will be in doubt himself of wether he is right..... was you engine coil light flashing at any point.!!!

Posted on Mar 30, 2009

  • 1 Answer

SOURCE: front end shaking

I had the same problem on a 2003 Kia Sedona where the front end would vibrate excessively while accerating at freeway speeds. Over time it got worse and was noticable at lower and lower speeds and while just maintaining speed, but went away when I took my foot off the gas.

It turned out to be the inner CV joint on the passenger side. You can check for this by grabbing the inner and outer half axels with large vice grips or slip-joint pilers and turning them in opposite directions while listening for crunching or "loose parts" noises.

The CV is sold with the axle so I just bought the outer half axle for $80 (which has the inner and outer CV joints attached) and replaced it. If you do it yourself, make sure you have a ball spline fork, a hub puller tool, and a big torque wrench for putting the bearing assembly back on. You can rent these at AutoZone.

The bad CV joint also caused the bearing to go bad. It had burn marks and made a grinding noise while turning. It was very hard to get out, so I had to take the assembly to a machine shop to have it taken out and the new one put in. $35 for bearing and $30 for machine shop work.

After repair, I took an 800 mile road trip that weekend with no problems other than barely noticable vibration from the driver side at 70+ mph. I figure vibration was so bad pre-repair that it messed up something on the other side as well, so I'll check out the driver side bearing and CV when I get a chance.

Posted on May 05, 2009

  • 206 Answers

SOURCE: spare tire tools

From the owner's manual for that model, see link below also, page 299 of the PDF has a nice picture.

Spare Tire Removal
Fit the jack handle extension over the drive nut. Use the
Lug Wrench to rotate the nut counter clockwise until the
spare is on the ground with enough slack in the cable to
allow to pull the tire out from under the vehicle.
CAUTION!
The winch mechanism is designed for use with the
jack extension tube only. Use of an air wrench or
other power tools is not recommended and can
damage the winch.
When the spare is clear, tilt the retainer at the end of the
cable and pull it through the center of the wheel.

http://www.jeep.com/en/owners/manuals/index.html?year=2006&nameplate=Grand%20Cherokee

Posted on Oct 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need a 2013 jeep compass fuse diagram layout, looking for AC fuse & relay position


post symptoms.
1: open glovebox, read operators guide yet, no.
2: open hood, open TIPM box read lid yet, no.
3: read the shop manual yet, no.
it dont work like you think !! not at all .
it has a COMPUTER Now that runs all that.
in the TIPM called"electronics module" and has no fuse
or vastly less by design.
4: did you scan it first., no and that is a big problem there. as the EM is on a NETWORK. (network bus)

https://www.techauthority.com/en-us/products/?year=2013&model=668&type=

Mar 13, 2017 | 2013 Jeep Compass

1 Answer

I NEED TO REPLACE THE TAIL LIGHT ASSEMBLY ON A 2013 JEEP COMPASS


ok we watch you and laugh as you drop tools
oh fun....
most users manual cover this, read much
rtm
http://owners.mopar.ca/en/

Feb 04, 2017 | 2013 Jeep Compass

1 Answer

My 2007 checy impala read "calibration complete" what does that mean ????


CALIBRATION COMPLETE
Refer to Electronic Compass Calibration do you have an owners manual ?
Compass Calibration
The compass direction will show CAL if it needs to be calibrated. Before calibrating the compass, drive the vehicle to an area that is magnetically clean (free of large metallic objects).
  1. Turn ON the ignition.
  2. Before calibrating the compass, make sure the compass is set to the variance zone in which the vehicle is travelling. See Compass Magnetic Variation Adjustment below.
  3. Press the vehicle information button until the PRESS TO CALIBRATE COMPASS screen is displayed.
  4. Press the set/reset button to start the compass calibration.
  5. The DIC will display CALIBRATING: DRIVE IN CIRCLES. Drive the vehicle in circles at less than 8 km/h (5 mph) to complete the calibration. The DIC will display CALIBRATION COMPLETE when the calibration is complete.

Oct 02, 2016 | 2007 Chevrolet Impala

3 Answers

2009 fusion SEL has data compass error after being rear ended and a shop did repair.


WHAT IS A COMPASS ERROR FOR A 2009 FORD FUSION ...

www.fixya.com/cars/t16705785-compass_error_2009_ford_fusion
Feb 21, 2013 - WHAT IS A COMPASS ERROR FOR A 2009 FORD FUSION A MESSAGE COMES UP ON MY DASH SAYS COMPASS NO ... SOURCE: I HAVE A2009 FORD FUSION AND IT'S NOT GOING OVER 20 MPH ... Compass data error -- how do i determine my zone-- ... Jan 28, 2010 ' 2007 Ford Edge SEL Plus.

Compass - Ford Fusion Sport - Ford Fusion Forum

www.fordfusionforum.com/topic/9390-compass/
Jan 23, 2013 - Compass - posted in Ford Fusion Sport: 2011 Fusion SEL without navigation screen. Following windshield ... I have recalibrated and reset the compassaccording to the manual instructions (several times) but cannot correct the error. Can anyone help? ... picture of where it is: 2009-08-30_051718_2.gif.

Nov 08, 2015 | 2009 Ford Fusion

2 Answers

07 jeep compass wont go over 10 mph


Did you bend a drive line part. A arm or any control arms .,., are traction control lights flashing???

Dec 11, 2013 | 2008 Jeep Compass

2 Answers

Where do I install the block heater for a Jeep Compass 2007 model,4x2 basic model


What brand is it ., if it's a silicon pad stick it to bottom or side of oil pan somewhere (heat rises) if it's a dip stick kind stuff it in dipstick holeand run it., . Oh remove heat dipstick replacing with old one when starting a driving veh.,.my personal opinion

Dec 09, 2013 | 2009 Jeep Compass

1 Answer

Compass direction wrong


Compass Calibration
Before calibrating the compass, drive the vehicle to an area that is magnetically clean or free of large metallic objects. Verify there are no magnetized objects on the inside or outside of the vehicle close to the mirror.

Start the engine.
Press and hold the switch for the compass, which may be depicted as COMP, COMPASS, or On/Off (w/UE1) depending on the type of mirror on the vehicle, until the letter "C" or "CAL" is displayed.
Drive the vehicle in circles at a speed of less than 8 km/h (5 mph) until the "C" or "CAL" is replaced by a proper vehicle heading. The calibration procedure is now complete.
Compass Magnetic Variation Adjustment
Magnetic variation adjustments are required when the compass displays a constant error in heading. Variation is the difference between magnetic north and true north due to geographical location.

Nov 09, 2010 | 2004 GMC Envoy

1 Answer

Built in electronic compass on 2004 GMC Envoy is giving the wrong directions


Try the following;

Compass Calibration
Before calibrating the compass, drive the vehicle to an area that is magnetically clean or free of large metallic objects. Verify there are no magnetized objects on the inside or outside of the vehicle close to the mirror.

Start the engine.
Press and hold the switch for the compass, which may be depicted as COMP, COMPASS, or On/Off (w/UE1) depending on the type of mirror on the vehicle, until the letter "C" or "CAL" is displayed.
Drive the vehicle in circles at a speed of less than 8 km/h (5 mph) until the "C" or "CAL" is replaced by a proper vehicle heading. The calibration procedure is now complete.
Compass Magnetic Variation Adjustment
Magnetic variation adjustments are required when the compass displays a constant error in heading. Variation is the difference between magnetic north and true north due to geographical location.

Nov 09, 2010 | 2004 GMC Envoy

1 Answer

Adjsut compass


If it's a Donnelly or Gentex try Pressing the compass button until it displays a "C". Do this in a area where you can drive slowly in a circle several times. Like a empty parking lot. That should reset the unit. the owners manual should give you the correct procedure too.

Feb 07, 2010 | 1999 Isuzu Trooper

1 Answer

I have 2002 Yukpn Denali XL. There is a OC code that appears in the rear view. What is the cause of this and how can I fix it?


The "OC" indicates your compass is "Out of Calibration". Below is the proceedure to recalibrate your compass.

Compass Calibration
The compass may need calibration if:
 After five seconds, the display does not show a
compass heading (N for North, for example), there
may be a strong magnetic field interfering with the
compass. Such interference may be caused by a
magnetic antenna mount, magnetic note pad holder
or a similar magnetic item.
 The compass does not display the correct heading
and the compass zone variance is set correctly.
In order to calibrate, the letters CAL must be displayed
in the mirror compass windows. If CAL is not
displayed, push in the COMP button for approximately
eight seconds or until the letters CAL are displayed.
The compass can be calibrated in one of two ways:
 Drive the vehicle in circles at 5 mph (8 km/h) or less
until the display reads a direction, or
 drive the vehicle on your everyday routine and after
several turns the compass will become calibrated and
will display a direction.

Good luck.

Oct 23, 2009 | 2003 GMC Yukon XL

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...