Question about GMC Sierra 1500

Open Question

How to change oil pump on 2000 gmc sierra - Sierra 1500 GMC Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 250 Answers

SOURCE: Changing a water pump on a 2005 GMC Pick-up

Open the hood of your truck. Look inside the engine bay. See the fan assembly and the pulley that the belt rides on. The water pump is behind the pulley. Changing water pumps can be somewhat of a task. Professional help will be needed for someone that can't find the waterpump. 


 The water pump is on the passenger side front of the engine; I had to drain the coolant, I kept the belt in place, then I removed the 3 bolts from the pulley to give me access to the bolts on the top (it will require a set of metric tools for it). Then I removed the passenger side front tire and the splash cover from under the car just above the tire, removed all bolts that holds the pump on the lower part of it, then removed the belt, scraped and clean very well the old gasket. The new water pump came with a new gasket, so I just got a gasket maker and applied to the gasket, so I did not have to do it again. Work backwords to reinstall everything, good time to replace the coolant and if you have not done yet, replace the thermostat valve along with any hose that may be cracked, rigid or enlarged (check the hoses to the heater core also). Please check your belts and hoses so you will not have to redo the process again. 


Posted on Jan 29, 2009

Ad
  • 6 Answers

SOURCE: 2000 gmc sierra 1500 5.3 v8. a/c heater control problem

your heat/cool and vent selection options are controlled by engine vacuum through small clear tubes attached to the rear of your climate control interface. Other vehicles have small steel pull wires that operate the desired changes. You might try removing the trim and any fasteners affiliated with the interface/console. GENTLY pull outward and look to see if any of these tubes are pulled off or cut/damaged. Did anyone recently install a new stereo in the vehicle? If so, the vacuum tubing and or pull wires that change your outlets could have been damaged when the stereo unit was pushed into place. Hope this helps

Posted on Sep 09, 2009

Testimonial: "Very good information. THANKS!"

SOURCE: Got oil cahnged and now change oil soon light is

Turn the ignition on and within a few seconds slowly pump the gas pedal three times. A message displaying "oil life reset" should show up in the drivers information center. If you have the "newer" driver information center look for an "i" button and scroll through it until you see "oil life **%" displayed. At that point press and hold the reset button until it resets to 100%. Should take about 10 seconds of holding the button.

There should be instructions on how to reset it in the owners manual if this doesn't help. Good luck.

Posted on Oct 06, 2009

  • 5 Answers

SOURCE: 2000 gmc starts but then idles rough then dies

I had to replace the mass air flow sensor. $ 150. the engine would shut off when driving too.changed fuel filter only worked for a day. The sensor is just after air filter.

Posted on Dec 01, 2009

Tnsiouxfalls
  • 617 Answers

SOURCE: my 2000 gmc sierra won't start. changed the

Just maybe it's mechanical.Internal to the steering column is an activator rod that manually makes the contact in the ignition switch.It's the cast piece that is molded to the activator rod that breaks.Two things you can do;tilt the steering wheel all the way up and try again to start(the cast piece spreads before it breaks,by tilting you gain a little extra throw on the switch).This will only work a couple times before complete failure of the casting.The other is to move the cover that's just below the tilt lever enough to get to the rod and move it with a pliers to start.If it's mechanical these things do work,I ran my truck with a vice grip for a couple weeks until I could get the parts for the repair,but replacing the broken part is smarter and won't scratch up your column like mine.

Posted on Dec 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Oil pump on 05 gmc 1500


it's in the oil pan usually .

Mar 21, 2016 | 2005 GMC Sierra 1500 Hybrid

1 Answer

My high milage 2000 GMC Sierra has an oil pressure problem when cold the pressure is good but as it gets hot it drops to the point the low oil pressure light comes on. I believe it is either the oil pump...


The oil pump is on the front of the engine. the pan and front of the engine has to come off. the crankshaft drives the pump. the cross member bolts in. you may check the oil pick up tube first. sometimes a mechanic has a bore scope and can go up in the oil pan drain hole and look at the screen. Its a lot of work/money to be guessing. good luck

Sep 15, 2011 | 2000 GMC Sierra

1 Answer

How to reset oil change light?


Make and Model: Chevrolet Suburban, GMC Yukon XL, Chevrolet Silverado, GMC Trucks Sierra
Years: 2000-01, 1999-00

Turn the ignition key to the RUN position. Fully push and release the accelerator pedal 3 times within 5 seconds. If the CHANGE OIL SOON light flashes 2 times, the system is reset. However, if the light comes on and stays on for 5 seconds, the system did not reset. Repeat the procedure if the system does not reset.

Hope this help (remember rated and comment this help) Good luck.

May 14, 2010 | 1999 GMC Sierra

2 Answers

LOW OIL PRESSURE ON 2007 GMC SIERRA 1500. CHANGED


have it tested using a manual gage if still low then main baring ore most likely bad that would mean a over hall if is really low and bearings bad should be making rattle noise when started up first few seconds

Mar 11, 2010 | GMC Sierra 1500 Cars & Trucks

1 Answer

2000 gmc starts but then idles rough then dies


I had to replace the mass air flow sensor. $ 150. the engine would shut off when driving too.changed fuel filter only worked for a day. The sensor is just after air filter.

Nov 27, 2009 | 2000 GMC New Sierra 1500

1 Answer

1990 GMC Sierra lifters knocking. Oil pressure


I doubt it....It could be a totally worn out engine.

Nov 13, 2009 | 1990 GMC Sierra

1 Answer

2000 GMC SIERRA 2500 LIFTER NOISE


Try a cup of tranny fluid, Dextron, or whatever, in the crankcase. Or there are lots of lifter products at your local part store. I would certainly try that first. I assume your oil has been changed recently, and the level is good. You don't have to pull the heads, but you do have to remove the intake, and valve covers.

Sep 03, 2009 | 2000 GMC Sierra

1 Answer

2000 gmc sierra fuel pump


Orig factory electric fuel pumps turn off seconds after loss off oil pressure

Mar 28, 2009 | 2000 GMC Sierra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...