Question about 2004 Chevrolet Blazer

Open Question

2004 blazer, problem shifting to four wheel drive, only four wheel low works after several attemps, works right after battery is diconnected for a few minutes but problem returns after a short time

Has push buttons for the four wheel drive shift

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 33 Answers

SOURCE: 1994 chevy s10 blazer 4x4 push button type

small sylinoid on the top of the transfer case needs replaced. easy to do. it has three vacumelines going to it just trun out and replace like a bolt.

Posted on Dec 13, 2008

Ad
  • 159 Answers

SOURCE: 94 s10 blazer wont go out of four wheel drive

The electric shift solennoid on the transfer case is probably bad,common problem with these.

Posted on Dec 25, 2008

  • 3 Answers

SOURCE: 1998 chevy blazer won't go in to four wheel drive

It sounds like the encoder motor. That's the black plastic box on the driver's side of the transfer case. But just to make sure, the control module for the encoder motor is located behind the passenger side kick plate (inside the vehicle, passenger side, where your feet would be, outside side). Disconnect it for a few seconds and then reconnect it. If the problem still exists, you will have to repair or change your encoder motor. I grabbed one at a scrap yard for less than $100.00.

Posted on Jan 04, 2009

billie17
  • 84 Answers

SOURCE: 1999 Chevy Suburban wont kick into four wheel drive

if it is electronic there is probably something wrong with the wiring..

but if it is manual...it might be the actuator........



Posted on Feb 11, 2009

  • 1 Answer

SOURCE: 4x4 wont engage

There is a switch that has twwo wires going to it, it's located just above the motor on your transfer case,on the drivers side, one plug goes to the motor and the other goes to this switch, it's the motor that shifts it into low and high range, I'm not sure what the switch is called but it tells the front end when to lock and unlock.
Hope it helps

Posted on Mar 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 chevy blazer passenger front wheel noise


driving in 4wd on hard surfaces produces what is known as torque wind up as the wheels cannot slip so the variations of distance going around corners , dips in the road etc place considerable strain on the transmission , transfer case , drive lines and diffs
that is why it is difficult to get out of 4wd unless you drive with 2 wheels on a grass verge to relieve that torque wind up
as for the noise check wheel bearings and the cv ("U") joint at that wheel as there appears a proble where the dog teeth in the hub are not engaging properly or are jumping out of engagement

Mar 26, 2017 | 2000 Chevrolet Blazer

1 Answer

When drivingtruck in 2 wheel drive the 4 wheel low light will flash and when slow truck down to a stop it will shift into 4 wheel low and will not go back to 2 wheel high


Sometimes the solenoids will stick on the axle neither in 2 or 4 wheel drive, if this problem started when you weren't shifting between two and four wheel drive it is probably the push button switch cluster on your dash going bad

Dec 12, 2010 | 2000 Chevrolet Blazer

1 Answer

1997 blazer my four wheel drive stop working wont lock in four wheel what could it be


SHIFT LINKAGES LOOSE BENT OR BINDING AND WEAR.ALSO LOW ON LUBRICATION.COULD HAVE WORN INNER PARTS NEED A TRANSFER OVERHAUL.YOU COULD ALSO HAVE ELECTRICAL PROBLEM IN THE TRANFERCASE CONTROL MODULE OR FAILURE ALSO IN THE SHIFT MOTOR.

Jun 30, 2010 | 1997 Chevrolet Blazer

2 Answers

I have a 1996 chevy blazer and dont know how to disengage from four wheel drive to two wheel drive?


As I recall the 96 blazer had electronic shifting for 2wd to 4wd. There should be a small panel on the drivers dash buttons for 2wd, 4wd lo and 4wd hi.

Simply press the desired button while stationary and if the system is functioning properly then it will shift and the light for the engaged type of drive will be lighted. Generally you would like to be in 2wd for this vehicle.

Mar 10, 2010 | 1996 Chevrolet Blazer

2 Answers

Hello I drive a 2004 chevy blazer and when i switch to four high the light goes on, but doesn't kick into four high. Please help just got 19 inches of snow.


If the light fashes then stops without shifting I suspect the shift encoder motor. 4 low will only shift in nuetral

Feb 06, 2010 | 2004 Chevrolet Blazer

2 Answers

1996 chevy blazer will not go into 4wd hi but it will go in to 4wd lo. when you push the 4 Hi button it just flashes and then does nothing.


The major components to this system are a shift control motor that is mounted to the transfer case, and a shift control module that is behind your center console. since the transfer case is still shifting into 4wd lo, the shift motor is still moving somewhat, so the most likely cause is the shift control module, but there isn't an easy way to troubleshoot between the two...

Nov 16, 2009 | 1996 Chevrolet Blazer

2 Answers

Won;t shift to four wheel drive the light on the dash blinks


When this happens I would think you have an issue with your 4 wheel Drive that needs servicing.Most of the time it's the selector switch($400),See if a National Chain( transmission )has free or low cost evaluations.Good Luck.

Sep 17, 2009 | 2004 Toyota 4Runner

1 Answer

1993 4X4 BLASER 4WHEEL DRIVE


Your blazer is equipped with a shift on the fly four wheel drive. That means that at speeds less than fifteen miles per hour you can shift into or out of four wheel drive by simply pushing the four wheel high button. If you wish to shift into four wheel low. Stop, put the transmission into park or neutral, and push the four wheel low button. Same procedure for shifting back out. Never shift into or out of four wheel low while moving. And be careful in four wheel low. At full throttle your still barely moving, you don't want to blow your engine up!

Dec 31, 2008 | 1994 Chevrolet S-10 Blazer

1 Answer

94 s10 blazer wont go out of four wheel drive


The electric shift solennoid on the transfer case is probably bad,common problem with these.

Dec 25, 2008 | 1999 Chevrolet Blazer

1 Answer

Transmission


I had that problem in my 1998 Blazer. There is a module on the passenger side of the truck, next to where the passenger right foot be. Remove the side kick panel to get to module. Disconnect battery before unpluging and pluging new mudule in. This unit controls the electronic switching between 2 and 4 wheel drive..Wes

Jul 30, 2008 | 2000 Chevrolet Blazer

Not finding what you are looking for?
2004 Chevrolet Blazer Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...