Question about 1995 Ford Bronco

1 Answer

1995 Ford Bronco XLT, 5.0L-Manual transmission. After i start the truck i cannot get into first gear. i have to cycle through the gears a couple of times before i can get into first gear.

Also, while driving, sometimes I cannot shift into third gear. I have to stop the car and try going into first gear. Also, while driving, when I release the clutch, when shifting to another gear, the truck does a weird lunge forward.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

  • Contributor
  • 35 Answers

Synchro to be checked

Posted on Feb 07, 2014

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

csmock132
  • 4669 Answers

SOURCE: Manual transmission will not shift into any gear,

The problem sounds like the clutch. If you put it in 1st., then start it up, does it try to move with you foot on the clutch? Does the clutch pedal feel different than normal.

Posted on Jun 24, 2009

MEGA_MUZIK
  • 54 Answers

SOURCE: Ford Escape Automatic Only Goes Into 1st Gear Manually

it sound like you have a vacum leak or your shifter cable may need adjusted

Posted on Oct 27, 2009

oneStan
  • 430 Answers

SOURCE: push on clutch and caR WONT GO IN GEAR UNLESS MOTOR OFF

This sounds like the clutch cable has broken. Not that it couldn't be the diaphram on the pressure plate, but the cable is more than likely the problem.

It won't go into gear while running because the clutch isn't being depressed putting the transmission in a position to allow the synchronizers to work.

When you turn it off, you can easily shift into any gear, but trying to start in gear makes the car try to move. You can verify this by putting it into high gear and trying to start it, you'll still move but less due to clutch slippage. If you put it into reverse, it will try to go backwards-so don't do that!

good luck!

Posted on Mar 22, 2012

Testimonial: "That is so totally Dead ON!!!! Your Awesome.....THANK YOU SO MUCH for reading what I typed!!!...Now to figure out how to get it fixed...lol....Seriously THANK YOU!!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

86 bronco will not start in park only in neutral immediately goes dead when put in gear what could be the problem


Sounds like the torque converter is locked up.
You would have the same effect of a manual transmission with the clutch out and the trans in gear.

Feb 27, 2015 | 1986 Ford Bronco

1 Answer

1990 Ford Bronco II manual transmission extremely hard to shift will not go into reverse


90 Ford Bronco II: You have to put it in whichever gear you want it in before you start it or it wont shift at all. Then once you are going its extremely hard to shift into the other gears. Reverse is the only gear that sounds like its grinding.

Aug 16, 2013 | 1990 Ford Bronco II

1 Answer

1995 Ford Bronco engine dies when shifted into drive but runs in reverse or 1st gear


Could be fuel filter,air filter,tune up,wires,coils.low idle too low.

Jun 13, 2013 | 1995 Ford Bronco

1 Answer

1995 ford explorer xlt not moving when on gear?


Have some look at it,ur transmission cold be done

Mar 27, 2013 | 1995 Ford Explorer

1 Answer

WHERE IS THE SPEEDOMETER FUSE ON A 88 FORD BRONCO XLT (FULL SIZE my speedometer and milege gadge isnt working ..was told to ck the fuse ...wher is that??


Sorry there is no fuse for this it runs off of the speedometer cable, the gear on the end is bad or the connection the the transmission is loose or not attached. it is on the drivers side of the transmission toward the back of the transmission..

Oct 26, 2010 | 1988 Ford Bronco II

1 Answer

Where can i find a transmission sensor for a 1995 ford bronco xlt full size


try car-part.com for used part. page with asterisk is lowest price.

for new at discount, tascafordparts.com

for obsolete, try green sales who buys a lot of Ford obsolete.

Nov 03, 2009 | 1995 Ford Bronco

1 Answer

Speedometer going out be linked to problem with truck shifting


the cable is a mechanical part which you can do yourself,not to much money.thats where i would start

Jun 09, 2009 | 1993 Ford Bronco

1 Answer

1988 Bronco II transmission pop out of 1st gear


there are dent and brass balls that are in your transmission and are used to hold the shifter into each gear when it starts poping out of that means that those dents and brass balls are worn down and i would suggest getting the transmission rebuilt.

Dec 16, 2008 | 1988 Ford Bronco II

1 Answer

1995 Ford Bronco dies when coming to a stop.


The idle air control solenoid could be bad. give the engine a vacuum leak and see if that helps any

Oct 15, 2008 | 1995 Ford Bronco

Not finding what you are looking for?
1995 Ford Bronco Logo

191 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...