Question about 1991 Nissan Sentra 2 Door
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Easy job ! just rem to get a gear puller for the antilock gear and install same as came off old one Parts around 100$ each apx 1/2 hr each side
Posted on Oct 15, 2008
Yes it is as easy as it looks. If you had the tire off and figured out that it looks easy, you shouldn't have much problem.
Posted on Mar 21, 2009
They should be replaceable w/o pulling the axle. Imagine a common nail; you have the shank of the nail with its point and the flat head on the other end. Your lug stud looks a little like that except the part that comes through the axle flange. It is a little larger than the threaded part and has "lateral lines" machined into it to grip inside the flange. Otherwise it would spin either way when you tried to tighten or remove it. To get the broken ones out, use a high quality flat end punch and a hammer to drive them backwards (toward the center of your differential) and eventually out of the flange. Look for the area that will give you the most room so they will not hit aything while they are backe out of the flange. The new studs can be installed in the reverse manner. When you get them just barely started through the flange, use your fingers to twist them back and forth to "feel" for the grooves where the old stud was seated. Once you get it barely started in the grooves, grease the threads, slip an old 1/2 inch drive socket over the new stud (make sure it doesn't fit tight) slip on a thick flat washer or 2--3 thin ones, turn your lug nut around backwards so the tapered end faces out and begin to tighten it. Go slow, make sure the new stud pulls through the flange evenly. Take the nut, washers and socket off every now and then and look at your progress. When the back side of the stud is seated on the back of the flange, you're finished. Now, always grease the studs. ALL OF THEM, EVERY WHEEL. The monkeys that put on tires these days use impact wrenches and if you just have to let them do it, grease will help you loosen the nut if you have to and it will help prevent future failures. A DRY stud and nut causes a twisting motion to take place in the body of the stud when its tightened. This leads to premature metal fatigue.
Posted on May 03, 2009
SOURCE: broken wheel stud
1. get new studs and nuts
3. remove caliper at bracket to spindle connection(2 18mm bolts?)you may need to remove caliper from bracket,but not always nessacery. Or remove drum,then to #5
4.remove rotor,will need a hammer, tap inbetween studs dont wreck good studs and see if new studs can be installed without removing parking brake shoes. If there is no clearance to get new stud in you will need to remove shoes.
5.Pound out old studs place new stud in hole use a washer on outside then put a nut on and tighten to install stud, A air gun or some type of impact tool will be very helpful. Check to see that stud has enough threds to pull stud all the way thru ,add more washers if nessecary dont let the nut run out of threds it will **** to get back off and wreck new stud.
6. if you dont have air gun or feel comfertable removing brakes bring it to a reputable garage, shouldnt cost more than $70+ parts to get all new studs put in on one wheel.
Posted on May 17, 2009
Tips for a great answer:
Jan 25, 2015 | Ford Cars & Trucks
Aug 31, 2010 | 1984 Nissan 300ZX
Jul 15, 2010 | 1999 Nissan Maxima
Apr 12, 2010 | 2003 Nissan Sentra
May 17, 2009 | 2002 Nissan Sentra
May 17, 2009 | 2003 Nissan Sentra
Mar 21, 2009 | 2002 Nissan Sentra
Feb 27, 2009 | 1990 Nissan Sentra
Jun 12, 2008 | 2003 Nissan Sentra
May 27, 2014 | 1991 Nissan Sentra 2 Door
21 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: