Question about Cars & Trucks

Open Question

Tyre pressure for 1999 nissan 1400 champ bakkie

What is the recommended tyre pressure with no load

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

bunnydawg
  • 5158 Answers

SOURCE: What is the correct tyre pressure for a small Nissan Lucino?

should be a sticker on the door jamb on either the drivers or passenger side door that gives you that information

Posted on Apr 14, 2009

  • 10 Answers

SOURCE: where can i find a workshop manual for a nissan

nissan website or nissan dealer

Posted on Jul 19, 2009

  • 1341 Answers

SOURCE: Loaded Tyre pressures for Daewoo Lanos 1.6SX

Inflating your tyre to 35 or more depends on the distance you are travelling and the amount of weight you will carry.Even though the manual says 32 somtimes if you have heavy load then you need to put a bit more than 35..

Posted on Jul 25, 2009

yourpc
  • 190 Answers

SOURCE: I NEED A NISSAN 1400 BAKKIE FUSE BOX WIRING

I get files from www.pdftown.com I have been able to download manuals for several of my cars there. Hope this helps...

Posted on Sep 10, 2009

oneStan
  • 430 Answers

SOURCE: nissan 1400 champ front brakes binding, brake

This indicates that you have air in the brake system or something isn't mounted properly. You'll need to inspect to see if there is anything not properly mounted, I'll deal with the brake bleeding:

You will need to bleed the brakes from the right rear first, then the left rear, right front, then left front brake, all without letting the brake Master Cylinder resivoir from getting low while doing the bleeding.

You may even want to start with the master cylinder to make sure it's bled properly by loosening the lines there first, bleeding them & then continuing to the system. Use the guide below for best results.

Bleeding brakes properly:
1. 2 people are required to do this properly, forget one man bleeders, they do work, but don't talk back or identify problems as they can't see what's happening. As a safety feature it's good to have another person nearby when someone is getting underneath a vehicle. Even my wife has had to do the pedal pushing in my household when I didn't have an assistant and needed to bleed either a brake system, or a clutch system.

2. Never let the fluid go beneath half way down when bleeding the brakes.

3. When adding fluid to the master cylinder, use a funnel to allow the fluid to run down the side into the cylinder, or use a syringe to prevent air from entering the fluid as you pour it.

4. Always pump the brakes slowly, release them slowly. Fast pedal action causes the fluid to rise into the air, allowing air to enter the system.

5. Pressurize the system by pumping repeatedly until the pedal is as firm as it will get, continue to hold that pedal down until the person bleeding the brakes, has released the air by loosening the bleeder valve, then make sure the line is tightened BEFORE releasing the brake pedal slowly. Pump the pedal again to build pressure, & bleed the brake again the same way until air stops coming out & only good fluid is seen. Proceed to the next farthest line.

If done this way, the brakes will be properly bled and if there are no leaks, the system should work properly. If you identify a leak, repair and start over.

good luck

Posted on Feb 28, 2010

Testimonial: "thanx very much for the help that was the problem"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a nissan 1400 champ 95 model.When i drove home bakkie starts to miss like it dont get petrol but if ref high the miss is gone,when low it dies.I have clean it and put new gaskets,still the same


Ignition modules have two sections--a low speed section and a high speed section. Tests of these often are not accurate, so replacement is the only real test.

Aug 12, 2016 | Nissan Cars & Trucks

1 Answer

Hi I need the Big End Torque settings for a Nissan 1400 Champ bakkie


Mains Stage 1 83nm , Mains Stage 2 167nm Big ends Stage 1 29nm Big ends Stage 2 45 - 60 degrees


26213454-gixnvmegknfegt3ailar3alb-5-0.jpg

Jun 06, 2016 | Nissan 1400 Cars & Trucks

1 Answer

I drive a Nissan 1400 bakkie (not a champ) i drives good and then starts jerking and wants to die as soon i i give petrol it sounds like its smothering


hi, personally ..i love that bakkie. Ok you changed points condensor, petrol filter! please check.. When it cuts out 1. if the ignition coil is not hot, if so thats your problem.2. also on the carb... over the needle and seat there is a tiny filter... somtimes gets blocked. 3. also check when it stolls if the fuel pump is not hot or pull the outlet fuel from the pump
and crank the engine... note if fuel comes out sufficiently.

May 21, 2014 | 2006 Nissan 1400 Bakkie

1 Answer

Where is the flasher relay on a nissan 1400 bakkie


this is a super old question, 3 years old, is it worth answering?

Feb 10, 2012 | Nissan 1400 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...