Question about Cars & Trucks

Open Question

Location camshaft position sensor bmw 545i 2005

Where is the camshaft sensor located i have poo14 code

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 39 Answers

SOURCE: Where is the camshaft position sensor located-99 Chevy Lumina 3.1

It's held down by one bolt right above the timing chain cover. It's next to the head that's facing toward the front of the car.

Posted on Feb 06, 2009

Ad
emissionwiz
  • 76846 Answers

SOURCE: camshaft position sensor location

At the right rear of the engine under the intake manifold and to the left of the oil filter. You will probably need to go under the car to spot it, it's the sensor with a three-wire connector arranged vertically. But you can take it out from above. It's held in with a single bolt with an eight MM head located just above the sensor. Un-clip and remove the electrical connector. Unscrew the bolt with a socket wrench & extension bar. Wiggle and pull the sensor out.
here is a picture.
255f615.jpg

Posted on Apr 10, 2009

  • 218 Answers

SOURCE: Camshaft Position Sensor Location

IF U GO TO THE RIGHT SIDE OF THE ENGINE AND LOOK 4 INCHES BEHIND THE BELT IT WILL BE ON TOP OF THE TIMING COVER.THE WIRES WILL BE RED/WHITE,BLACK,BROWN/WHITE

Posted on May 05, 2009

  • 51 Answers

SOURCE: locating and replacing a camshaft sensor in a 2005 dodge neon

this is a very very simple procedure. you do not need pics. there is a sensor located at the end of the engine on the far side from the belts. at the top. it has a plug with two wires in it. just remove the two 10mm bolts un hook the plug and reverse the process to reinstall. if you have a factory intake you may have to remove it to access this sensor. just the intake tube.

Posted on Aug 08, 2009

  • 144 Answers

SOURCE: Where is the camshaft position sensor located in a 2001 VW Passat

when you are looking at the engine pull off the plastic cover on top then the front cover that covers you timing belt there is a wire harness tha goes right to it in the left upper coner two ten mil bolts and it comes off careful not to drop bolts down in belt that could be bad. it is that easy

Posted on Sep 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Check engine light code p0014 p0013


hi got 2012 mercedez benz c250 i change the camshaft actuators intake and exhaust. first thing i change becouse make a lot noise when'd is cool now i put the actuators the noise is gone for two days now i got the code poo14 now is jerking and shaking ???

Nov 20, 2013 | 2007 Mercedes-Benz ML350

1 Answer

I went to scan my toyota yaris car and the following codes were give ; temperature ckt low input po117


EOBD II Error Code: P0117
Fault Location:
Engine Coolant Temperature (ECT) Sensor (G62) - Low Input
Possible Cause:
Malfunction Indicator Lamp (MIL) Triggered on first occurrence.
Coolant thermostat.
Wiring short to earth.
Engine coolant temperature (ECT) sensor.

EOBD II Error Code: P0340
Fault Location:
Camshaft Position (CMP) Sensor A (G40), Bank 1 - Circuit Malfunction
Possible Cause:
Malfunction Indicator Lamp (MIL) active.
Wiring from/to Camshaft Position Sensor (CMP) faulty.
Camshaft position (CMP) sensor faulty.
Timing misaligned.
Possible Solutions:
Check Wiring from/to Camshaft Position Sensor.
Check Camshaft Position Sensor.
Check Timing.

EOBD II Error Code: P0500
Fault Location:
Vehicle Speed Sensor (VSS) - Circuit Malfunction
Possible Cause:
Malfunction Indicator Lamp (MIL) Non Emission Fault - No warning light.
Wiring.
Vehicle speed sensor (VSS).
Engine control module (ECM).

Dec 13, 2012 | 2001 Toyota Yaris

1 Answer

Where is the camshaft position sensor on a 1998 Dodge Dakota 5.2L


The camshaft position sensor is located on the distributor for all engines designed for the 1998 Dodge Dakota. Accessing the sensor requires removing the distributor cap and the distributor rotor. The camshaft sensor pigtail comes through the front of the distributor and connects to the engine wiring harness above the intake manifold.

Oct 03, 2012 | Cars & Trucks

1 Answer

Code po606 is coming up on my 2004 trail blazer


P0606 is an indication that the engine computer (PCM) has an internal fault, it may require reflashing.
P0014 is Camshaft position timing-over advanced, this could be a result of the PCM problem.

Jul 29, 2012 | 2004 Chevrolet TrailBlazer

1 Answer

Poo14 code came up need to locate on truck where the cam sensor is


The exhaust cam sensor is on the right front corner of the cylinder head. (DRIVER RIGHT). To your right of the upper radiator hose.

Jan 01, 2012 | 2005 Chevrolet Colorado

2 Answers

Has a code of p0014


THIS IS THE CAMSHAFT PHASER SOLENOID CODE. most likely you need to replace the solenoid it is on the right side of engine (passenger side) it is a cylynder looking valve about 3" long easy to change.

Jun 24, 2011 | 2005 Chevrolet TrailBlazer

1 Answer

2004 trailblazer has a code of poo14


The code is a code that has had a lot of controversy in this subject. I have provided a link to another site that will explain in depth on what the code is and what is needed to be done to get the job done correctly.

http://forums.trailvoy.com/showthread.php?t=28340&highlight=Camshaft+actuator

Jun 24, 2011 | 2004 Chevrolet TrailBlazer

1 Answer

What is the most likely problem for codes POO14 and POO17 on a 2006 GMC Canyon with a 3.5 engine?


this is set from camshaft and crankshaft sensor, always check engine oil for the right vescocity and change oil if necessary to avoid this dtc set

Jul 20, 2010 | 2006 GMC Canyon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...