Question about 2009 Jeep Patriot

Open Question

How to Remove the two push-pins from the taillamp housing.

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do i remove my rear axles on my 1977 dodge aspen


Top of Form 1
Raise the vehicle and remove the rear wheels.
Clean all dirt from the housing cover and remove the housing cover to drain the lubricant.
Remove the brake drum.
Rotate the differential case until the differential pinion shaft lockscrew can be removed. Remove the lockscrew and pinion shaft.
Push the axle shafts toward the center of the vehicle and remove the C-locks from the grooves on the axle shafts.
Pull the axle shafts from the housing, being careful not to damage the bearing which remains in the housing.
Inspect the axle shaft bearings and replace any doubtful parts. Whenever the axle shaft is replaced, the bearings should also be replaced.
Remove the axle shaft seal from the bore in the housing, using the button end of the axle shaft.
Remove the axle shaft bearing from the housing. Do not reuse the bearing or the seal.
Check the bearing shoulder in the axle housing for imperfections. These should be corrected with a file or polish.

Apr 24, 2011 | Dodge Diplomat Cars & Trucks

1 Answer

How to change the brake light on 1997 ford taurus


Please don't forget to rate! Thank you!


  1. Disconnect the negative battery cable.
  2. Open the trunklid.
  3. Remove the quarter trim panel.
  4. Remove the three retaining nuts for the taillamp assembly.
  5. Carefully pull the rear lamp assembly away from the vehicle.
  6. Detach the bulb(s) socket electrical connector.
  7. Rotate the bulb(s) socket counterclockwise approximately 1/4 of a turn and remove the socket from the lamp assembly.
  8. Remove the bulb(s) from the socket by pulling the bulb straight out.
  9. The installation is the reverse of the removal.
// // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 45; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]> var _strTreeScrollHidName = 'ctl00_hidTreeScrollPos';

c17hydro_84.gif

Remove the trim clip center retainer and...



c17hydro_85.gif

... remove the clip from the trim



c17hydro_86.gif

Remove the trim from the trunk



c17hydro_87.gif

Carefully pull back the trim to access the taillamp retaining nuts. Remove the retaining nuts and...



c17hydro_88.gif

... pull the taillamp away from the body to...



c17hydro_89.gif

... detach the connectors for the taillamp bulbs and...



c17hydro_90.gif

... rotate the bulb sockets from the taillamp assembly



c17hydro_91.gif

Pull the bulb straight out to remove it from the socket

Jan 16, 2011 | 1997 Ford Taurus

1 Answer

Change tail light on 2007 pontiac solstice


Taillamps, Turn Signal, and Stoplamps
To replace one of these bulbs, do the following:
1. Open the trunk. See Trunk on page 68 from Owners Manual for more information.

zjlimited_135.jpg

2. Remove the two screws, which hold the taillamp assembly, from inside the vehicle.
3. Remove the taillamp assembly.
4. Turn the bulb socket counterclockwise to remove.
5. Pull the bulb from the socket.
6. Install a new bulb.
7. Reverse the steps to reinstall the taillamp assembly.


Hope this helps to solve it.

Nov 25, 2010 | 2006 Pontiac Solstice

1 Answer

Trying to change a rear light bulb and dont know how to open it up


Rear Turn Signal, Brake & Parking Lights The taillamps, stoplamps and rear turn signals lamps are all incorporated into the rear taillamps. The taillamps are lit whenever the parking lamps or headlamps are in operation. The rear turn signal lamps flash with the front turn signal lamps whenever a turn is indicated with the turn signal/headlamp dimmer switch. The stoplamps light whenever the brake pedal is depressed and the stoplamp switch is closed.



6ab94c9.gif

The trim panel is likely held in place with retainers like this. Back out the screw to release tension on the pin legs and remove the fastener


f6d727d.gif
The taillamp is retained by plastic wingnuts


5a0b7de.gif
Remove the plastic wing nuts from the taillamp housing


a75c041.gif
Remove the taillamp housing from the vehicle to service the light bulbs


  1. Open the rear compartment (trunk).
  2. If equipped, unhook the convenience net that stretches between the taillamps. It is attached to hooks molded into the plastic taillamp assembly retaining wingnuts. Loosen the rear compartment trim panel. It is retained by plastic pins with a screw in the center. Back out the screw to release any tension on the plastic pin legs, and pull the trim (thin carpet-like material) for access to the taillamps.
  3. Remove the plastic taillamp assembly retaining wingnuts.
  4. Remove the taillamp assembly from the vehicle and service the light bulbs as required.
  5. Installation is the reverse of the removal process.
  6. Test the lights for correct operation.

Apr 29, 2010 | 1999 Pontiac Grand Prix

1 Answer

How do you remove an Ignition Lock Cylinder from a 91 saab 900s


Option A
  1. remove driver side seat
  2. insert the key and turn to midway between "lock" and "accessories" position,
  3. push stiff wire tool such as metal coat hanger, into the hole in the side of the gear housing at the ignition lock, to push in the spring loaded pin in the housing
  4. while pushing on the pin, pull out on the key to remove the cylinder
  5. to re-assemble, reverse the procedure; check that the tooth segment driver pins in the gear lever housing are in the correct position to receive the new cylinder
  6. push in the spring again, and insert the cylinder until it clicks

Option B
  1. Cut down a spare key so that it's about 1.5 inch long measured from the tip, and has no lobes.
  2. unscrew the console: two screws under the shifter boot, two screws in the rear base visible after removing the ashtray.
  3. insert the key in the ignition, turn to "run", put shifter in neutral.
  4. lift console up on shifter lever, if necessary you can undo the three Torx T25 bolts holding shifter into base and lift it out, to completely remove the console.
  5. undo the gear lever housing nuts, needs a special Saab tool but you can make one yourself, it just has three tabs equidistantly spaced - here's a pic, 13c7448.jpegfrom saabcentral forums
  6. remove the lever housing, place in a vice, and follow Option A above.

Feb 16, 2010 | 1991 Saab 900

1 Answer

How do you remove the air filter box on a 2001


REMOVAL
Release hood latch and open hood.
Access Rubber Grommet
Remove large rubber grommet (70 mm x 168 mm) from splash shield to gain access to fascia fasteners.
Fastener Locations

Remove fasteners attaching fascia to the front fender and splash shield, using access hole in splash shield.
Remove Push In Fasteners
Remove the push pins attaching the fascia to the upper radiator closure panel.
Headlamp Jack screws

Remove jackscrews attaching headlamp housing to crossmember and remove the lamp housing to access the lamp(s).
Roll Fascia Forward

Roll fascia forward to clear way for headlamp housing removal.
Disconnect wire connector from back of lamp socket(s) and/or bulbs.
Remove Headlamp Housing

INSTALLATION
CAUTION : Do not touch the glass of halogen bulbs with fingers or other possibly oily surface, reduced bulb life will result.

Place headlamp housing into position.
Connect wire connector to lamp socket(s)
Verify headlamp and signal lamp operation.
Install jackscrews to attach headlamp housing to crossmember.
Align fascia to bumper reinforcement and install the top center push pins, to upper radiator closure panel.
Align the two fascia studs to the fender vertical attachments, at the same time align the fascia groove on the horizontal flange with the fender drive pin. Push fascia rearward to engage the fasteners.
Install nut on fascia stud through the splash shield access hole.
Verify headlamp operation and alignment


Nov 03, 2009 | 2001 Chrysler 300M

1 Answer

2007 Tahoe tail light


1. Open the liftgate.
2. Remove the two screws from the taillamp assembly.
3. Pull the taillamp assembly rearward until you
disengage the inner pins on the taillamp
assembly from the vehicle.
4. Press the release tab, if bulb socket has one,
and turn the bulb socket counterclockwise to
remove it from the taillamp assembly.
5. Pull the old bulb straight out from the bulb
socket.
6. Press a new bulb into the bulb socket and
insert it into the taillamp assembly. Turn the
bulb socket clockwise into the taillamp
assembly until it clicks.
7. Reinstall the taillamp assembly. When
reinstalling, make sure to line up the pins on
the taillamp assembly with the vehicle. If
you do not do this, you will not be able
correctly install the taillamp assembly.

May 02, 2009 | 2007 Chevrolet Tahoe

1 Answer

How do you replace headlamp bulbs on 1999 chrysler 300


You half to remove the Headlamp housing to change it. Here is the instructions out of the factory manual.
Tell me if this works for you?
HEADLAMP HOUSING - CONCORDE/LHS/330M Headlamp lens fogging is a normal condition and does not require service unless excessive or continual. Moisture will vent from tubes or vents located on the back of the lamp.
REMOVAL
  1. Release hood latch and open hood.
  2. Remove large rubber grommet (70 mm x 168 mm) from splash shield to gain access to fascia fasteners Access Rubber Grommet
  3. Remove fasteners attaching fascia to the front fender and splash shield, using access hole in splash shield Fastener Locations
  4. Remove the push pins attaching the fascia to the upper radiator closure panel Remove Push In Fasteners
  5. Remove jackscrews attaching headlamp housing to crossmember and remove the lamp housing to access the lamp(s) Headlamp Jackscrews
  6. Roll fascia forward to clear way for headlamp housing removal Roll Fascia Forward
  7. Disconnect wire connector from back of lamp socket(s) and/or bulbs.
  8. Remove headlamp housing Remove Headlamp Housing
INSTALLATION CAUTION: Do not touch the glass of halogen bulbs with fingers or other possibly oily surface, reduced bulb life will result.
  1. Place headlamp housing into position.
  2. Connect wire connector to lamp socket(s) and/or bulbs.
  3. Verify headlamp and signal lamp operation.
  4. Install jackscrews to attach headlamp housing to crossmember.
  5. Align fascia to bumper reinforcement and install the top center push pins, to upper radiator closure panel.
  6. Align the two fascia studs to the fender vertical attachments, at the same time align the fascia groove on the horizontal flange with the fender drive pin. Push fascia rearward to engage the fasteners.
  7. Install nut on fascia stud through the splash shield access hole.
  8. Verify headlamp operation and alignment

Mar 27, 2009 | 1999 Chrysler 300M

1 Answer

2002 Tahoe stop light bulb replacement


yes, remove the two screws, and firmly yet carefully pull the taillamp assembly back out of the quarter panel. Once you have the taillamp out of the body and in hand, the sockets (on the back of taillamp) must be rotated to remove them from the lens. If memory serves, they must be rotated counter clockwise to release the socket from the lens housing, however, they will ONLY turn one way. plug your bulb into the socket and reverse the process. will only take about 5 minutes.

Dec 09, 2008 | 1999 Chevrolet Silverado 1500

1 Answer

Replace tail lamp


There's a carpet lining in your trunk, to remove that from the rear part of the trunk you'll need to undo some nut-type caps with small plastic screw/pin things in them that hold in this carpet. After that you'll see the back of your taillight assembly and the obvious 3 nuts you need to remove to remove the taillamp.

May 15, 2008 | Toyota Solara Cars & Trucks

Not finding what you are looking for?
2009 Jeep Patriot Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...