Question about 2010 Mercedes-Benz Sprinter

Open Question

Def system fail

After fill up with def fluid def light is on restarts counting down

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is the red indicator light on the Diesel exhaust fluid flashing?


Red usually indicates a system fault, or a low DEF level

Feb 14, 2017 | Cars & Trucks

1 Answer

How do l get low def lite,no start counter and code 16cf00,18b400,15b700,131e00,17900 to reset.


PDF Manual Document Search

5.249.144.94/
I have the check engine light on and the scan read P0135 error - what is this? .... lite,no start counter and code 16cf00,18b400,15b700,131e00,17900 to reset.

The unit will not stay on unless it is plugged into the wall

www.greatbook.tk/F/.../t26023273-unit_will_not_stay_unless_plugged_i...
... condition · Emergency brake repair on 1992 Chevy lumina · How do l get low def lite,no start counter and code 16cf00,18b400,15b700,131e00,17900 to reset.Missing: error

Dec 29, 2015 | Cars & Trucks

1 Answer

Service exhaust soon on 2011 2500 hd


There is a tank that is along the frame rail and it hold DEF (diesel Exhaust Fluid) when the tank is almost empty, you get that message to fill it. 5.3 gallons is what it holds and it gets 1300 miles to the gallon.

Jan 28, 2013 | 2011 Chevrolet Silverado 2500HD

1 Answer

2012 windshield washer fluid low light came on but when I filled the fluid the light did not go out


A 2012 should be under warranty . These cars have to be scanned when lights come on usually because of their computers. It could be as simple as a reset, but I would take it to the dealer, or try running the fluid low purposely, and filling it up again as they may have a float inside the washer resevior sticking, Toyota is good to fix their customers up, if all else fails, I would bring it in. Hope this was helpful

Jan 02, 2013 | Toyota Camry Cars & Trucks

1 Answer

How do i check fluid for convertable top


"How do I get the air out of my hydraulic system"?
  • Remove the reservoir plug on the motor pump. Leave the plug out and do not put back until you have finished.
  • Fill the reservoir 3/4 full with fluid (to the bottom of filler plug hole). Put a rag under the hole to catch overflow that will occur as system fills.
  • Run the pump for 15-20 seconds. Stop. Check your fluid level and refill to bottom of filler hole. Continue running the motor in the same direction for an additional 15-20 seconds. When the top gets to the end of cycle, check your fluid level, fill to bottom of filler hole, and run the motor in the opposite direction.
  • You are literally running the top all the way up and down sereral times. Checking the fluid level as you go and fill as required, leaving reservoir 25% empty.
  • When you are no longer able to add fluid, put the top in the down position. Check the fluid level one last time, should be to bottom of filler hole. Put the plug into reservoir.
    "How do I get the air out of my hydraulic system"?
  • Remove the reservoir plug on the motor pump. Leave the plug out and do not put back until you have finished.
  • Fill the reservoir 3/4 full with fluid (to the bottom of filler plug hole). Put a rag under the hole to catch overflow that will occur as system fills.
  • Run the pump for 15-20 seconds. Stop. Check your fluid level and refill to bottom of filler hole. Continue running the motor in the same direction for an additional 15-20 seconds. When the top gets to the end of cycle, check your fluid level, fill to bottom of filler hole, and run the motor in the opposite direction.
  • You are literally running the top all the way up and down sereral times. Checking the fluid level as you go and fill as required, leaving reservoir 25% empty.
  • When you are no longer able to add fluid, put the top in the down position. Check the fluid level one last time, should be to bottom of filler hole. Put the plug into reservoir.
  • Apr 01, 2012 | 2004 Ford Mustang

    1 Answer

    Red light by speedometer is on looks light an eye. don't have owner's manual.


    I believe the warnin light symbol your are referring to is the low brake fluid warning.
    If the wave and the filled in area is at the bottom 1/3 of the circle.
    Check the brake fluid in the reservoir to see if it is low.
    Many times if it is low, the light will come on when slowing down, and go off when
    accelerating because the fluid is sloshing around.
    If it is low, then have the system checked for leaks.
    Leaking rear wheel cylinders is a common cause for low fluid.
    Also low front brakes pads can cause the system fluid to be low.

    Feb 22, 2011 | 2001 Chevrolet Venture

    1 Answer

    Whenever i apply the brake when going down a hill, my brake light comes on....it does not stay on, but comes on frequently I have a 2007 Chrysler Sebring


    Hello dbrunner.
    Your brake fluid is low.
    In the master cylinder there is a float level that turns on a switch when it is low and turns on the brake light.
    When going down a hill the fluid runs to the front of the reservoir and the level drops turning on the light.
    Fill with DOT3 brake fluid only. Anything else will ruin the braking system.
    Also may be a good idea to have your braking system inspected for leaks and brake wear.

    There you are, best of the season to you.

    KL

    Dec 27, 2010 | Chrysler Sebring Cars & Trucks

    1 Answer

    1995 Jaguar convertable XJS quarter light windows wont go up


    The rear windows are controlled by a timer in the top's ECU. If
    the rear windows stop fully closing before your top is closed, the
    problem MAY be with top's hydraulic system.

    Check your top's hydraulic reserve tank for low fluid level. Lack
    of fluid will greatly delay the top's closing sequence, leaving
    those rear windows partially open.
    Your top's hydraulic pump system is located beneath the right side
    of the cubby/storage box behind the front seats. Raise the cover
    and you'll see a removable trim panel on the right side. The pump
    is behind that access panel.

    You can use power steering fluid to top off the tank, but don't
    fill it above level indicator line. You may have to add more fluid
    after you cycle the top up and down to get the air bubbles out of
    the lines.
    It could also be a relay. On a 95 the relays that are in the trunk above the battery.
    Perhaps, just switching the relays might prove which one is failing..

    Mar 24, 2010 | 1995 Jaguar XJ-R

    1 Answer

    2 PART QUESTION, PARKING LIGHTS IN FRONT NOT WORKING AFTER REPLACING WITH WORKING BULBS, BACK LIGHTS WORK .... REPLACED THERMOSTAT HEATER STILL NOT BLOWING AS WARM AS IT SHOULD GOES FROM COLD TO WARM BUT...


    Concerning the heater problem.Sounds like you have an air pocket in the system.To remove the air pocket take off the radiator cap in the morning when the car is cold,fill radiator to top.Start the car.Turn on heater to high.Allow car to run until it gets to operating temperature.Now you will see the fluid in the radiator start to go down.This means the thermostat is opening.As fluid goes down fill radiator to top (with 50/50 antifreeze/water mix).You may have to wait a moment for it to continue to move down.Once it stops and the radiator fluid isnt going down,slowly bring up the rpm's (by either turning the throttle with your hand or have someone put their foot on the gas) to about 2000rpms and hold the rpm's there steady.As you hold the fluid will go down a little more.As it does fill to the top again and quickly put the radiator cap back on while the rpm's are steady at 2000.After the cap is correctly on release throttle.This should remove the air posket.

    Oct 09, 2009 | 1996 Ford Crown Victoria

    2 Answers

    My 2001 corvette has a abs light on dash board


    The Light is on because the ABS system for your Anti-Lock Brakes has failed....the Brakes will still work...but the ABS wont...basically if you slam on the brakes... you will lock up your tires as if it were an older model car before ABS came out. The most probable cause is a wheel sensor that "Counts" the notches on the wheel axle near the knuckle has failed. Could just be dirty...mis-adjusted or broken.i would need more details to determine the exact cause. Hope this helps.

    Jun 04, 2009 | 2001 Chevrolet Corvette

    Not finding what you are looking for?
    2010 Mercedes-Benz Sprinter Logo

    Related Topics:

    80 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Mercedes-Benz Experts

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    yadayada
    yadayada

    Level 3 Expert

    76164 Answers

    Michael Contreras
    Michael Contreras

    Level 2 Expert

    166 Answers

    Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...