Question about Cars & Trucks
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Clean all dirt and/or grease from the
fuel filter fittings. "Quick Connect" fittings are used on models
equipped with a pressurized fuel system. These fittings must be
disconnected using the proper procedure or the fittings may be damaged.
The fuel filter uses a "hairpin" clip retainer. Spread the two hairpin
clip legs about 1/8 in. (3mm) each to disengage
it from the fitting, then pull the clip outward. Use finger pressure
only; do not use any tools. Push the quick connect fittings onto the
filter ends. Mazda recommends that the retaining clips be replaced
whenever removed. The fuel tubes used on these fuel systems are
manufactured in 5/16 in. and 3/8
in. diameters. Each fuel tube takes a different size hairpin clip, so
keep this in mind when purchasing new clips. A click will be heard when
the hairpin clip snaps into its proper position. Pull on the lines with
moderate pressure to ensure proper connection. Start the engine and
check for fuel leaks. If the inertia switch (reset switch) was
disconnected to relieve the fuel system pressure, cycle the ignition
switch from the OFF to ON position several times to re-charge the fuel system before attempting to start the engine.
Remove the "hairpin" clip retainers to access the fuel line fittingsThe inline reservoir type fuel filter should last the life of the vehicle under normal driving conditions. If the filter does need to be replaced, proceed as follows:
CAUTIONIf the fuel filter is being serviced with the rear of the vehicle higher than the front, or if the tank is pressurized, fuel leakage or siphoning from the tank fuel lines could occur. to prevent this condition, maintain the vehicle front end at or above the level of the rear of vehicle. also, relieve tank pressure by loosening the fuel fill cap. cap should be tightened after pressure is relieved.
Posted on Oct 17, 2008
fuel pump in the fuel tank note that all ford are equipt with cut of suitch (interuptor) located under dach board in case of colision ,towing, ect.....this electrical devise wil stop the flow of the fuel to prevent car fire
Posted on Dec 21, 2008
The fuel filter is attached to a bracket located in the left rear of the
engine compartment. Look down in the space between the master cylinder
fluid reservoir and the rear of the air filter compartment, you will be
looking at the top of the fuel filter cannister. It's very hard to get
Hope helped (remember comment and rated this).
Posted on Apr 10, 2010
SOURCE: where is the fuel filter
The fuel filter for your vehicle is located on the Fuel Pump Unit, which is located in the vehicle fuel tank. The Fuel Pump Unit must be removed from the top of the fuel tank in order to replace the Fuel Filter.
Posted on Feb 27, 2011
Tips for a great answer:
Feb 06, 2017 | Mazda Cars & Trucks
Mar 30, 2016 | Mazda Cars & Trucks
Jan 17, 2016 | Mazda Cars & Trucks
Nov 06, 2012 | Cars & Trucks
Jun 06, 2012 | 1999 Mazda B-Series
May 25, 2011 | 1998 Mazda B-Series
Apr 21, 2011 | Mazda B2600 Cars & Trucks
Feb 27, 2011 | 2004 Mazda MPV
Dec 21, 2008 | 1988 Mazda B2600 Cab Plus
93 people viewed this question
Usually answered in minutes!