Question about 2010 Chevrolet Captiva 2.0D

Open Question

Wiper linkage How to replace the front wiper linkage

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace the wiper motor on a 98 rodeo


the front or rear, no way for me to guess?????
unbolt it and replace it.
start at the arms and work inward works.

ill toss coin land on front.
ill read the FSM online for you, so can you , but here ill do it.

Motor
  1. Disconnect the negative battery cable.
  2. Disconnect the wiper power motor connector (2).
  3. Remove 4 mounting bolts.
  4. Remove the nut of the wiper motor shaft, and disconnect the linkage.
  5. Remove the windshield wiper motor (1).
To facilitate the removal of the nuts, be sure to put out the tip portion of the linkage sufficiently through the mounting hole of the motor by sliding the wiper blade slowly.


my guess is this the most easy motor on earth to change.
its in plain view, not burried deep in a cowl.....

it's
easy-peasy-japanesy..

Feb 22, 2015 | 1998 Isuzu Rodeo

1 Answer

Repair wiper linkage


Most likely the spline is stripped where the wiper blade connects to the linkage. All I do is insert a wire ( soft metal, like bailing wire) between the wiper arm and the linkage and tighten down the nut. But if the linkage doesn't move, then the linkage set has to be replaced. I have yet to find replacement parts for these. Salvage yard is your best bet.

Oct 10, 2014 | Chevrolet Cavalier Cars & Trucks

1 Answer

How to change front wiper motor on 1993 ford explorer


Hi there,
  • Turn the ignition on, and turn the front windshield wipers on. When the wipers are facing straight up on the window, turn the ignition off so they remain in that position.
  • Disconnect the negative battery cable with an adjustable wrench. Remove the passenger side wiper blade assembly, by removing the pivot nut at the bottom with an adjustable wrench. Remove the wiper linkage access cover, and use a screwdriver to remove the wiper motor clip. Remove the wiper linkage from the wiper motor.
  • Disconnect the electrical connector on the wiper motor. Remove the bolts and nuts, securing the wiper motor with a socket wrench. Remove the wiper motor from the vehicle. Install the new wiper motor, and tighten mounting bolts and nuts with a socket wrench. Connect the electrical harness to the new wiper motor. Connect the wiper linkage, and insert the linkage clip. Install the wiper blade assembly, and tighten the nut with an adjustable wrench.
  • Connect the negative battery cable securely, using an adjustable wrench.
Hope this helps...

Jan 24, 2011 | 1993 Ford Explorer Limited

1 Answer

Our front windshield wiper has quit working. it swings freely if you move it by hand. how do you repair it?


Remove the black plastic cowling that goes around the wipers in front of the windshield and behind the hood. Then check to see if the rod linkage that operates the wipers has come off, or time to replace wiper motor, but most likely the linkage has come apart.

Jan 20, 2011 | 2001 Ford Explorer Sport

1 Answer

Front windshield wippers stoped working still hear motor humming but nothing happens


Hi,
Sounds like your wiper linkage have loosen up or the linkage from the motor arm got disconnected.
The solution would be to bring that car to your mechanic or dealer to have them reconnect the wiper linkage, a plastic clip lock might have broken and needs to be replace, the parts is less than $5.
Hope that solves your problem!
Thanks for using Fixya!

Dec 15, 2010 | 2006 Kia Sportage

3 Answers

How easy is it to replace the front wiper motor on a 2004 ford escape ? Where is it located ?



Front Wiper Motor
Removal & Installation

NOTE A new wiper motor assembly comes with the linkage arm installed.
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the windshield wiper mounting arm and pivot shaft
    WARNING Do not remove the wiper motor linkage arm from the wiper motor assembly. If the arm is removed, the wiper arms may not park in the correct location.
    NOTE Use a suitable tool to separate the wiper linkage arm from the wiper mounting arm and pivot shaft assembly.
  3. Remove the 3 bolts and the wiper motor.

    7f7866e.gif

    Fig. Wiper motor and linkage

To install:
  1. Install wiper motor and bolts.
  2. Tighten wiper motor bolts to 10 ft. lbs. (13 Nm).
  3. Install windshield wiper mounting arm and pivot shaft.
  4. Check wiper operation.

Rear Wiper Motor
- Removal & Installation
  1. Remove the rear pivot arm.
  2. Remove the rear wiper motor shaft nut cover
  3. Remove the rear wiper motor shaft nut.
  4. Open the lift gate window.
  5. Remove the rear wiper motor cover trim panel.
  6. Disconnect the electrical connector.
  7. Remove the 2 rear window wiper motor nuts
  8. Remove the rear window wiper motor.

    79be491.jpg
    Fig. Rear wiper motor view-2008 model shown, other years similar

To install:
  1. Install rear wiper motor and tighten mounting nuts to 62 inch lbs. (7 Nm).
  2. Reconnect the electrical connector.
  3. Install wiper motor cover trim panel.
  4. Install rear wiper pivot arm tighten nut to 53 inch lbs. (6 Nm).
  5. Install shaft nut cover.
  6. Check wiper operation.

Good luck (remember rated this post).

Feb 25, 2010 | 2004 Ford Escape

3 Answers

Wiper problem 2002 ford explorer. Motor energizes, but wipers won't move unless you give them a "shove". How do you access the wiper drive system ? Thanks


it is problem with linkage of motor , you have to lubricate it then try once, but the motor is gone weak so it not pushing that linkage, you just try with lubricating that linkage that connected to wiper motor to wiper arm, if it work you saved your money or do replace the motor assy.

Jan 24, 2010 | 2002 Ford Explorer

2 Answers

Wipers worked one turn then stopped


may have broken bushing in one of the arms in the wiper linkage, remove the cowl and take a look. most part stores sell replacement bushings start there good luck.

Jan 07, 2010 | Mitsubishi Colt Cars & Trucks

1 Answer

Driver's side wiper arm on my '93 Sidekick is not working


This is what I Found there was not any Illustration's with it looks Fairly simple, Good luck



FRONT
  1. Disconnect linkage assembly from wiper motor shaft.
  2. Disconnect electrical connectors from wiper motor.
  3. Remove wiper motor attaching bolts, then wiper motor.
REAR
  1. Remove wiper blade and arm assembly.
  2. Remove access panel on back door.
  3. Disconnect linkage assembly from wiper motor shaft.
  4. Disconnect electrical connectors from wiper motor.
  5. Remove wiper motor attaching bolts, then wiper motor.
Skill
Level
Mfg.
Warranty
Standard Wiper Motor Labor Replace Front B 0.7 1.0
PLEASE DONT FORGET TO RATE ME Thank You Much

Jan 20, 2009 | 1995 Suzuki Sidekick

Not finding what you are looking for?
2010 Chevrolet Captiva 2.0D Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...