Question about 2006 Honda Odyssey

Open Question

Noise behind glove box 07 honda pilot ac not blowing cold

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Brian032472
  • 150 Answers

SOURCE: How to change the HEPA cabin filter in a 2006 Honda Civic

Open the glove box and there are push out tabs on the left and right side pop them out. Now watch it because you are about to dump the contents of your glove box on the floor. let the box hang freely from the lower hinge and look in the back. You will see a white panel that pulls out the panel has a tray attached with the filter element in it remove old element and replace with new 20ish bucks at the parts store lots more at the dealer. re-install filter tray and reverse your removal steps to re-install. Recommended approx 15k or annually

Posted on Nov 04, 2008

Mike258
  • 1498 Answers

SOURCE: 1996 honda civic wont start

Hi Meadors,

The clicking sound you heard most likely the starter solenoid engaging the starter. Only in this case it's failing to engage the starter. This is a classic symptom of a low battery. Here's why.

In a perfect world, when you turn the key to start:

  1. the solenoid is fed 12VDC which engages an electromagnetic coil inside it.
  2. A spring loaded steel piston inside this coil reacts to the magnetic field. It is pulled against the spring. By itself this sounds like a loud decisive CLICK.
  3. The movement of the piston simultaneously pushes the starter gear into the flywheel and sends power to the starter via heavy duty contacts. The starter draws a lot of power.
  4. The starter spins, turns the engine, the engine starts, life is good.
  5. When the key is released, the solenoid disengages, the spring pushes the piston back, the starter gear disengages from the flywheel.
In our world, when you turn the key to start:
  1. The solenoid which draws it's share of power engages as before. Click.
  2. As the starter tries to spin, the power available is insufficient. It draws all remaining power, there isn't enough left to keep the solenoid active and it turns off.
  3. Since the starter isn't drawing power anymore, the solenoid re-engages and the cycle starts over. Click.
  4. The cycle repeats. Click. A series of rapid clicks. Same page?
While a dead battery is the prime suspect, there can be other causes. Things to do:

  • Check belts, specifically on the alternator.
  • Terminal connections clean and tight.
  • In the 'Let's not over look the obvious' department: Battery voltage?
  • Get a jump. Try a jump start.
  • If a jump gets you going, it is either the battery not holding a charge or the alternator not providing one.
Even new batteries can be bad off the shelf. Especially if they have been on that shelf for a while. They may show the voltage but not the amps. This is called a 'Surface Charge'.

If you don't have a voltmeter, what you need to do now is visit an auto parts store (not a shop). Most (in the hope of making a sale) will provide free testing of batteries and charging systems.

What you need is called a "Load Test" on the battery. It simulates the load of an engine being started. This will confirm the battery is good or bad.

Then with the car running, they need to check the voltage to the battery (they will know this). If it's not above +13VDC, the alternator is bad or not connected correctly.

And if it doesn't start, what better place to be?

Let me know what they and you find out by commenting.
Best regards
Mike

Posted on Jan 07, 2009

MrScary66613
  • 1990 Answers

SOURCE: Honda accord 07 making a highpitched squeaking noise in cold

That Squeeling is your Belt. You may need a New Belt Tensioner to keep it Tighter. As a Quick fix, Go to your Auto Parts Store and get a Can of Fan Belt Dressing and spray this on the Belt and it will be Quite for a while. Please Rate my Solution, I need all the Help I can Get! Thanks!

Posted on Jan 26, 2009

  • 58 Answers

SOURCE: How to change the cabin filter on 2006 Honda Odyssey?

I will never understand why this service is so expensive at the dealership.
I made a video showing how this is done:   (I would recommend watching the video in HQ and full screen)

Posted on Apr 21, 2009

jyackle5
  • 8197 Answers

SOURCE: how to replace cabin air filter in 2003 pilot

Step 1 Take everything out of the glove box on the passenger side. Squeeze the black clips on either side of the glove box interior to free it from its retainer and pull it toward you. It will glide forward on hinged arms. Lower it as much as possible so it's out of your way.

  • Step 2 Identify the gray plastic bar that runs from left to right across the bottom of the glove box opening. This is a piece of plastic molded to the rest of the glove box assembly, but it covers up a removable bar that is mounted directly in front of the cabin air filtermag-glass_10x10.gif case. You'll have to cut this plastic bar off with a razor knife to proceed. Fortunately, this isn't too difficult; just cut carefully and steadily, and make your cuts as close as possible to the ends of the bar.
  • Step 3 Remove the metal bar you uncovered in the previous step. It is screwed into the glove box assembly with Phillips head screws on either side.
  • Step 4 Open the cabin air filter case, which is the large plastic case on the left side off the glove box opening. The hatch will come all the way off when you open it.
  • Step 5 Take the old air filter out of the case and throw it away.
  • Step 6 Look at the arrows on the filter and the arrows on the filter case that indicate the direction of the air flow. Slide the new filter into place so that the arrows are both pointing the same way.
  • Step 7 Put the lid back on the air filter case and reinstall the metal bar you removed in Step 3.
  • Step 8 Push the glove box interior compartment back into place and listen for the snapping sound. Put the glove box contents back, close the lid and you're done.
  • Posted on Dec 06, 2009

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    I have a 95 honda civic lx. ac kicks on but blows warm air. checked freon levels and pressure and that was ok. what could be the problem? and im a diy guy so what part would i need


    First you will have to figure out if the ac system is working or not.
    If one of the ac lines is cold and the other is hot, you could have a blend door problem behind the glove box. The blend door directs air thru the heater core and the evaporator core.

    Jul 17, 2012 | 1995 Honda Civic

    1 Answer

    My 2004 ford explorer makes a clicking noise when selecting between cold and hot air. And the AC will not blow cold air / heater will not blow warm air.


    it is the blend door, driver side by gas pedal, very hard to get to, the door has a rotery gear that when the teeth break off, thats when you get the clicking sound

    Jun 06, 2017 | 2004 Ford Explorer

    1 Answer

    98 mercedes E320 AC blow cold on passager side and hot on driver side


    you have shutter actuators that are mounted externally on you heater core enclosure inbetween your dash and firewall most likely in center. if not in center then behind glove box.

    May 12, 2012 | 1998 Mercedes-Benz E-Class

    1 Answer

    I have a 2004 ford explorer. My ac only blows cold air and their is an knocking noise coming from the dash in the area around the ac. Can you please help?


    That is the blend door actuator. It is mounted on the top of the evaporator case behind the radio/glove box area. The plastic gears inside of that device wore their teeth off and won't open the heater core side of the case.

    Jan 23, 2012 | 2004 Ford Explorer

    1 Answer

    A/c / heat blows a little when off. also a/c


    clean or replace the in cabin air filter located behind the glove box. Remove the screw that holds the limit rod the the glove box, then squeeze both sides of the glvoe box to remove from dash. The air filter is behind the removable rectangular panel. See owner's manual for complete directions. Replace the AC clutch relay, $11 from rockauto.com. The relay is located in the under hood fuse box next to the battery. It is labeled M/G CLT.

    Apr 27, 2010 | 2004 Toyota Corolla

    4 Answers

    Where is the cabin filter on a 2003 honda odysseey


    The cabin filter is located behind the glovebox.
    First lower and remove the glovebox
    If it has not been changed before, you will need to cut the plastic crossbrace behind the glovebox.
    Once out of the way, unbolt the steel reinforcing frame behind the plastic and set it aside.
    The cabin filter is mounted vertically behind it.
    See images for further explanation:

    51b70ba.jpg
    645c9b6.jpg
    27573b7.jpg

    Feb 26, 2010 | Honda Odyssey Cars & Trucks

    1 Answer

    My 07 scion tc air conditioner hums/rattles how can I fix it


    If you pull out the glove box you will find the in cabin air filter, you probly want to replace it

    Jan 25, 2010 | 2007 Scion tC Coupe

    1 Answer

    Car rattles under right side of dash when accelerating


    The rattling sound coming from the a/c system may be a sign of a failing blower, or there might be an object hitting the blades.

    This can be inspected by an a/c technician, or if you are patient enough, you can check it yourself. Many automotive a/c blowers are located behind your vehicle's dashboard glove box.

    Hope this helps.

    Jul 02, 2009 | 2004 Honda CR-V

    1 Answer

    07 ranger stx a/c problem not blowing enought air


    hi one of your plastick vents has come of your main vent please check that all vents are ok in there right spots cheers peter

    Jul 21, 2008 | 2007 Ford Ranger FX4 Off-Road

    Not finding what you are looking for?
    2006 Honda Odyssey Logo

    Related Topics:

    33 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Honda Experts

    yadayada
    yadayada

    Level 3 Expert

    75822 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Kevin Daniels

    Level 3 Expert

    1455 Answers

    Are you a Honda Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...