Question about 2000 GMC Jimmy

1 Answer

Rf wheel bearing installation

Removal and replacement of rf wheel bearing

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • GMC Expert
  • 495 Answers

Remove wheel, brake caliper, etc., all items to gain access to hub assm...remove axle nut, hub mounting bolts, ABS harness, remove...

Posted on Nov 29, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wheel bearing right front


I think you must replace the entire hub assembly. You need a shop manual to do this correctly.

Feb 07, 2014 | 2000 GMC Jimmy

1 Answer

Replace Front Wheel Hub Bearing 2002 Jeep Grand Cherokee 2 wheel drive


Removal
  1. Raise and support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Remove the brake caliper, caliper anchor, rotor and ABS wheel speed sensor.
  4. Remove the cotter pin, nut retainer and axle hub nut.
  5. Remove the hub/bearing mounting bolts from the back of the steering knuckle. Remove hub/bearing from the steering knuckle and off the axle shaft.
Installation
  1. Install the hub/bearing to the knuckle.
  2. Install the hub/bearing-to-knuckle bolts and tighten to specification.
  3. Install the hub washer and nut. Tighten the hub nut to specification. Install the nut retainer and a new cotter pin.
  4. Install the brake rotor, caliper anchor, caliper and ABS wheel speed sensor.
  5. Install the wheel and tire assembly.
  6. Remove the support and lower the vehicle.

Apr 22, 2012 | 2002 Jeep Grand Cherokee

1 Answer

Nissan murano abs & awd inoperative after replacment of rf wheel bearing & r//l outer tie rod ends.


almost cetainly broke wheel speed sensor during bearing replacement.easy to forget to remove it before removing bearing assy.

Feb 01, 2011 | 2004 Nissan Murano

1 Answer

How to replace rear wheel bearing on 2003 hyandia sonata


Hub & Bearing Removal & Installation To Remove:
Hub bearing assembly (Typical) hyundai-08-00-6029.gif

  1. Release parking brake.
  2. Remove rear wheel assembly.
  3. Remove rear wheel speed sensor from carrier.
  4. Dismount brake caliper and support with mechanic's wire.
  5. Remove brake disc.
  6. Remove 4 axle hub mounting bolts. Special tool 09432-11000 (Typical) hyundai-08-00-6021.gif

  7. Using tool 09432-11000 (or suitable gear puller), remove tone wheel.
  8. Remove carrier.
  9. Remove stakes and remove flange nut.
  10. Support bearing outer race flange and press rear axle hub out.
  11. Using tool 09432-11000 (or suitable puller), remove inner race from axle hub.
To Install:
Hub bearing assembly (Typical) hyundai-08-00-6029.gif

  1. Apply thin coat of grease to bearing contact surface and hub.
  2. Using and appropriate tool, press bearing into hub. CAUTION
    Do not press against outer race of wheel bearing.
  3. Install flange nut and stake nut until it meets concave portion of spindle.
  4. Install carrier.
  5. Use an appropriate tool to press tone wheel.
  6. Install hub/bearing assembly with rounded portion of outer race facing up.
  7. Install 4 hub/bearing assembly bolts and rotate hub to seat bearing.
  8. Measure wheel bearing starting torque with a spring balance or equivalent device.
    • Starting torque should measure 15.9 in lb (1.8 Nm) or less
  9. Install brake disc.
  10. Mount brake caliper.
  11. Install rear wheel speed sensor to carrier.
  12. Install rear wheel assembly.
prev.gif next.gif

Oct 28, 2010 | 2001 Hyundai Sonata

1 Answer

Need to change front wheel bearing


Hub and Bearing Removal & Installation NOTE: The removal and installation of the wheel bearing and hub from the steering knuckle is only to be done with the steering knuckle removed from the vehicle
To Remove:
  1. Remove the steering knuckle and hub and bearing assembly.
  2. Remove a wheel lug stud from the hub flange using a C-clamp and Adapter Tool 4150A or equivalent.
  3. Rotate the hub to align the removed lug stud with the notch in the bearing retainer plate. Use a proper C-clamp and adapter tool to press out one of the lug studs 7922eg64.gif

    Rotate the hub in order to remove the lug stud 7922eg65.gif

  4. Rotate the hub so the stud hole is facing away from the brake caliper's lower rail on the steering knuckle.
  5. Install ½ of a Bearing Splitter Tool 1130 or equivalent between the hub and the bearing retainer plate. The threaded hole in this ½ is to be aligned with the caliper rail on the steering knuckle.
  6. Install the remaining pieces of the bearing splitter on the steering knuckle. Hand-tighten the nuts to hold the splitter in place on the knuckle. Proper installation of the bearing splitter 7922eg66.gif

  7. When the bearing splitter is installed, be sure the 3 bolts attaching the bearing retainer plate to the knuckle are contacting the bearing splitter. The bearing retainer plate should not support the knuckle or contact the splitter.
  8. Place the steering knuckle in a hydraulic press, supported by the bearing splitter. Properly support the steering knuckle for hub and bearing removal 7922eg67.gif

  9. Position a driver on the small end of the hub. Using the press, remove the hub from the wheel bearing. The outer bearing race will come out of the wheel bearing when the hub is pressed out of the bearing.
  10. Remove the bearing splitter tool from the knuckle.
  11. Place the knuckle in a press supported by the press block. The blocks must not obstruct the bore in the steering knuckle so the wheel bearing can be pressed out of the knuckle. Place a driver on the outer race of the wheel bearing, and then press the bearing out of the knuckle.
  12. Install the bearing splitter on the hub. The splitter is to be installed on the hub so it is between the flange of the hub and the bearing race on the hub. Place the hub, bearing race and splitter in a press. Use a driver to press the hub out of the bearing race.
To Install:
  1. Use clean, dry cloth to wipe and grease or dirt from the bore of the steering knuckle.
  2. Clean the rust preventative from the replacement wheel bearing using a clean, dry towel.
  3. Place the new wheel bearing into the bore of the steering knuckle. Be sure the bearing is placed squarely into the bore. Place the knuckle in a press with a receiver tool, C-4698-2 or equivalent supporting the steering knuckle. Place a driver tool on the outer race of the wheel bearing. Press the wheel bearing into the steering knuckle until it is fully bottomed in the bore of the steering knuckle. NOTE: Only the original or original equipment replacement bolts should be used to mounting the bearing retainer to the knuckle. If a bolt requires replacement when installing the bearing retainer plate, be sure to get the proper type of replacement.
  4. Install the bearing retainer plate on the steering knuckle. Install the 3 bearing retainer mounting bolts. Torque the bolts to 21 ft-lbs (28 Nm).
  5. Install the removed wheel lug stud into the hub flange.
  6. Place the hub with the lug stud installed, in a press supported by Adapter Tool C-4698-1 or equivalent. Press the wheel lug stud into the hub flange until it is fully seated against the back side on the hub flange.
  7. Place the steering knuckle with the wheel bearing installed, in a press with special Receiver Tool MB-990799 or equivalent supporting the inner race of the wheel bearing. Place the hub in the wheel bearing, making sure it is square with the bearing. Press the hub into the wheel bearing until it is fully bottomed in the wheel bearing.
  8. Install the steering knuckle and the wheel.
  9. Check and/or adjust the front alignment.
prev.gif next.gif

Oct 15, 2010 | 2004 Chrysler PT Cruiser

1 Answer

Wheel bearing assembly


I assume front.
I just finished this job on my 01 Aurora. 1) Loosen Axle Nut - 33mm (with tire on ground so you don't torque the trannie) 2) Remove wheel 3) Remove caliper 4) Remove Tie-Rod end 5) Remove bolts holding strut to wheel assy. 6) Remove axle nut 7) Remove 3 bolts holding wheel bearing (I use a lot of PB Blaster on nuts and around the flange of the wheel bearing.) 8) Disconnect the wheel Speed sensor wire. 9) Remove wheel bearing - it may be stuck. I use PB Blaster and a big cement chisel to get it loose 10) At this point I always replace the Half-Shaft if the car has 100K miles or more. The only cost $50.00 and you've aready done all the work to get to it. 11) Just tap the axle spline to remove the wheel bearing - you don't need a puller or anything like that. 12) Put it all back together. Don't forget the plate that holds the wheel speed sensor clip - I always seems to forget this!
Good luck.
P.S. I was sure the wheel bearing noise was coming from my L.F. bearing, but it had no play in it. (Hold wheel at the 12 and 6 positions and see if you have any play.) So at the last minute I jacked of the R.F. and found just a bit of play. I went for the R.F. and that was the one that was bad.

Jul 07, 2010 | 2000 Oldsmobile Intrigue

1 Answer

How do you remove the backing plate from an '05 Chev Venture rear hub so the hub can be replaced?


The 4 Bolts that Hold the HUB in Also Hold the Backing Plate
Hub Replacement - Rear (Front Wheel Drive/Drum)

Removal Procedure
  1. Raise and support the vehicle.
  2. Remove the tire and wheel.
  3. Remove the brake drum.
    1. Remove and DISCARD the wheel bearing/hub bolts.
    2. Remove the wheel bearing/hub.
    3. Disconnect the wheel speed sensor electrical connector (2).Installation Procedure
    4. Connect the wheel speed sensor electrical connector (2).
      1. Install the wheel bearing/hub. Caution: These fasteners MUST be replaced with new fasteners anytime they become loose or are removed. Failure to replace these fasteners after they become loose or are removed may cause loss of vehicle control and personal injury. Notice: Refer to Fastener Notice in Service Precautions.
      2. Install the NEW wheel bearing/hub bolts.
      1. Install the brake drum.
      2. Install the tire and wheel.
      3. Lower the vehicle.

Nov 07, 2009 | 2005 Chevrolet Venture

1 Answer

Frt. wheel bearings 2003 h-2


2003 Hummer H2 V8-6.0L VIN U
Wheel Bearing: Service and Repair
WHEEL HUB, BEARING, AND SEAL REPLACEMENT
REMOVAL PROCEDURE
NOTE: Never place vehicle on the ground with the halfshaft removed or the halfshaft nut torqued improperly. Otherwise, bearing seals may become
dislodged causing premature wear and/or damage to the hub and bearing assembly.
1. Raise and support the vehicle. Refer to Vehicle Lifting.
2. Remove the tire and wheel.
3. Remove the rotor.
4. Remove the wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle.
5. Disconnect the electrical connection for the wheel speed sensor.
6. Remove the wheel driveshaft nut retaining cover.
7. Remove the wheel driveshaft assembly retaining nut and washer from the wheel driveshaft assembly.
Disengage the wheel driveshaft from the wheel hub and bearing.
8. Remove the wheel hub and bearing mounting bolts.
9. Remove the wheel hub and bearing and splash shield from the vehicle.
10. Remove the O-ring seal from the steering knuckle bore.
11. Remove the wheel speed sensor from the wheel hub and bearing.
12. Clean and inspect the O-ring seal.
13. Replace the seal it the following conditions exist:
- Nicks
- Cuts
- Dry or brittle
- Compression set
INSTALLATION PROCEDURE
1. Clean all corrosion or contaminates from the steering knuckle bore and the hub and bearing assembly.
2. Lubricate the steering knuckle bore with wheel bearing grease or the equivalent.
3. Install the O-ring to the steering knuckle.
NOTE: Refer to Fastener Notice in Service Precautions.
4. Install the wheel speed sensor to the wheel hub and bearing.
Tighten
Tighten the sensor mounting bolt to 18 N.m (13 lb ft).
5. Install the wheel hub and bearing and splash shield to the vehicle.
6. Install the wheel hub and bearing mounting bolts.
Tighten
Tighten the wheel hub to knuckle bolts to 180 N.m (133 lb ft).
7. Install the nut and washer retaining the wheel drive shaft assembly to the wheel hub and bearing.
Tighten
Tighten the nut to 210 N.m (155 lb ft).
8. Connect the electrical connection for the wheel speed sensor.
9. Install the wheel speed sensor and brake hose mounting bracket bolt to the steering knuckle.
Tighten
Tighten the bolt to 12 N.m (106 lb in).
10. Install the rotor.
11. Install the tire and wheel.
12. Lower the vehicle.
907ae15.jpg


Sep 15, 2009 | 2003 Hummer H2

1 Answer

Directions replace front wheel bearings on a 1985 nissan stanza?


996fb79.gif

NOTE: After the wheel bearings have been removed or replaced or the front axle has been reassembled be sure to adjust wheel bearing preload. Refer to the Adjustment service procedure below. On the 1989–92 240SX there is just one wheel bearing, pressed into the hub and no adjusting cap. Refer to the exploded views of the Front Axle Hub Assembly. Review the complete service procedure.
  1. Raise and support the vehicle safely.
  2. Remove the front wheels and the brake caliper assemblies. NOTE: Brake hoses do not need to be disconnected from the brake caliper assemblies. Make sure the brake hoses are secure and do not let caliper assemblies hang unsupported from the vehicle.
  3. Work off center hub cap by using thin tool. If necessary tap around it with a soft hammer while removing.
  4. Pry off cotter pin and take out adjusting cap and wheel bearing lock nut.
  5. Remove wheel hub with disc brake rotor from spindle with bearings installed. Remove the outer bearing from the hub.
  6. Remove inner bearing and grease seal from hub using long brass drift pin or equivalent.
  7. If it is necessary to replace the bearing outer races, drive them out of the hub with a brass drift pin and mallet.
  8. Install the outer bearing race with a tool (KV401021S0 special tool number) until it seats in the hub flush. NOTE: Place a large glob of grease into the palm of one hand and push the bearing through it with a sliding motion. The grease must be forced through the side of the bearing and in between each roller. Continue until the grease begins to ooze out the other side through the gaps between the rollers. The bearing must be completely packed with grease.
  9. Pack each wheel bearing with high temperature wheel bearing grease. Pack hub and hub cap with the recommended wheel bearing grease up to shaded portions. Refer to the illustration.
  10. Install the inner bearing and grease seal in the proper position in the hub.
  11. Install the wheel hub with disc brake rotor to the spindle.
  12. Install the outer wheel bearing, lock washer, wheel bearing lock nut, adjusting cap, cotter pin (always use a new cotter pin and O-ring for installation after adjustment), spread cotter pin then install the O-ring and dust cap.
  13. Install the brake caliper assemblies and bleed brakes if necessary. Install the front wheels.

Jun 23, 2009 | 1985 Nissan Stanza

1 Answer

Rear axle bearing replacement



REAR WHEEL BEARING/ HUB

Removal Procedure
  1. Raise the vehicle. Refer to Vehicle Lifting in General Diagnosis.
  2. Remove the wheel and the tire. Refer to Tire and Wheel Removal and Installation in Wheels, Tires and Alignment.
    1. Remove and support the brake caliper. Refer to Brake Caliper Replacement (Front) or Brake Caliper Replacement (Rear) in Brakes.
    2. Remove the brake rotor. Refer to Brake Rotor Replacement in Disc Brakes.
    3. Remove the ABS sensor wire connector.
    4. Remove the four bolts from the control arm.
    5. Remove the hub and bearing from the control arm.
    6. Remove the brake shield from the control arm.
    7. Clean the control arm face and the bore before installing the hub and the bearing.
    Installation Procedure

    Notice: Refer to Fastener Notice in Service Precautions.
    1. Install the brake shield and the hub and the bearing to the control arm with the four bolts. Be careful not to drop the hub and the bearing, as it could be damaged. Reconnect the ABS sensor. Tighten the hub and bearing bolts to 70 Nm (52 ft. lbs.).
    2. Install the brake rotor. Refer to Brake Rotor Replacement in Disc Brakes.
    3. Install the brake caliper. Refer to Brake Caliper Replacement (Front) or Brake Caliper Replacement (Rear) in Disc Brakes.
    4. Install the wheel and the tire. Refer to Tire and Wheel Removal and Installation in Wheels, Tires and Alignment. Tighten the wheel nuts to 140 Nm (100 ft. lbs.).
    5. Lower the vehicle.

Feb 14, 2009 | 2002 Pontiac Bonneville

Not finding what you are looking for?
2000 GMC Jimmy Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...