Question about Chrysler PT Cruiser

Open Question

How to test coil pack on pt cruiser - PT Cruiser Chrysler Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76673 Answers

SOURCE: 2000 PT CRUISER

How about the MAF sensor?

Posted on Nov 23, 2008

Ad
  • 1 Answer

SOURCE: 2001 PT Cruiser quit running driving down highway

I HAD THE SAME PROBLEM, I BROKE A TIMING BELT.   HAD TO REPLACE THE ENGINE.

Posted on Mar 22, 2009

buffalonyman
  • 1865 Answers

SOURCE: pt cruiser misfires code p0351 have changed plugs

change the plug wires

Posted on Jul 23, 2009

  • 5 Answers

SOURCE: 2001 PT Cruiser: How too remove crankshaft pulley 2001 PT Cruiser...

GET A 3 SPOKE PULLEY EXTRACTOR AND SCREW IN THE BOLT BUT IN THE CRANKSHAFT HOLE PUT A MUCH SMALLER SCEW SO YOU WOUNT MESS THE INSIDE UP

Posted on May 26, 2010

  • 1 Answer

SOURCE: i changed the timing belt on a 2001 pt cruiser ,no

sell the damn thing, it would be the second best thing you done in your life. If you can sell it? drive it off a cliff. K

Posted on Jul 15, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

CODES P0441 AND P0304 CAME UP ON TEST? WHERE DO I START ON TRYING TO FIGURE OUT THE PROBLEM


P0441 = EVAP PURGEFLOW MONITOR that means insufficient or excessive vapor flow detected during evaporative system .
P0304= a misfire in cylinder # 3 answers to these p0441 a bad gas cap possible , and p0304 possible bad coil on cylinder #3, try clearing codes and see if they show back up or you get bad performance , then try replacing gas cap and then coil pack . I really hope this gets you on the right track .
Woody

Mar 05, 2015 | 2004 Chrysler PT Cruiser

2 Answers

2006 pt cruiser shut off while driving and won't restart?


Possibly the ignition switch. I had weird issues happiness with mine like that. I took it to the dealer and they quickly determined that the electrical part of the ignition switch had failed. They told me that thus is not uncommon in pt cruisers. They replaced it and all was well in the world.

Oct 15, 2014 | 2006 Chrysler PT Cruiser

3 Answers

Cylinders #2 and #3 aren't firing on a 2004 PT Cruiser. Already replaced cam and crank sensors.


Take out the harness connector (3 pin) from the ignition coil pack.
Point it to your self, the lock is upwards. There are 3 female pins on the connector. The right most connector is the switching signal wire to cylinder number 2 and 3 simultaneously. Center pin is 12 V supply and the left most is switching signal wire for cylinder number 1 and 4 simultaneously.
Now the problem may lie in:
- The high tension cords.
- The short or open circuit between the ignition coil pack connector and the ECM.
- Short or open circuit between the camshaft position sensor and the ECM.
- Short or open circuit between the crankshaft position sensor and the ECM.
- Valve timing incorrect, or timing belt tooth over jumped.
- Broken or damaged crank shaft sprocket.
- The ignition coil pack.

Jul 17, 2014 | 2004 Chrysler PT Cruiser

1 Answer

Pt cruiser cranks but won't start


Did you check to see if there is a neutral safety switch on the transmission?

Feb 02, 2014 | 2006 Chrysler PT Cruiser

1 Answer

Need to know where the crank shat sensor s located on a 2003 pt crusier


Follow your plug wires to your coil packs. Your coil packs are attached to the ignition module. There will two wires running form ignition module right to the crankshaft position sensor which should be in the engine block

Aug 07, 2010 | 2003 Chrysler PT Cruiser

1 Answer

I have a 2001 pt cruiser need to find where the crank sensor is located 4cyl


It is located next to crankshaft. Just follow spark plug wires to coil pack and module. Then follow from there and they lead directly to crank sensor.

Nov 19, 2009 | 2001 Chrysler PT Cruiser

3 Answers

Spit and sputter/2004 PT Cruiser


Check for fire to the coil pack. These have a tendency to go bad on these cars. Could be a cam or crank sensor, these also go bad. If you haven't changed the plugs in 30K, this is due also, wires every 60K. May need to actually get it hooked to a machine to find out for sure.

Jun 02, 2009 | 2004 Chrysler PT Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...