Question about Cars & Trucks

Open Question

$07E8 CAN OBDII - Cars & Trucks

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

ITEM 98568 P2138 $07E8 1/2 GENERIC THROTTLE/PEDAL POSITION SENSOR SWTCH D/E VOLTAGE CORELATION


You need to understand the causes of this fault, it is not always the throttle pedal sensor, it can also be wiring or the throttle valve sensor. Read about it at the link. P2138 Throttle Pedal Pos Sensor Voltage Correlation DTC

Jun 20, 2017 | Cars & Trucks

1 Answer

Cobalt 2009 4 cyl check engine came on so the code reader show 07E8


Did you try to sann parts store?do you have vaccum leak?

Mar 30, 2016 | Cars & Trucks

1 Answer

What is Saab code 1125 &07E8


The code 1125 is your throttle body, when they get dirty or stick they toss up a code. It will need to be replaced or cleaned. On Ford or GM cars we just remove them carefull not allowing dirt or tools to fall in after removing. Get some carb cleaner and clean all the dirt and carbon grime, out of it. be careful not to damage the sensor. Ask shop about cleaner you use not sure about safty on car made in Europe. Put back and things should be ok, If not you will need to replace it. Other code I believe is a junk code. readers seem to be not able to read sub codes unless it is from factory.

Jan 31, 2015 | Saab Cars & Trucks

1 Answer

What does $07e8 code mean?


wow, seen where, radio, nav, or cluster? or?
why not say where your finger is pointing.(or eyes gander)


means someone used the passenger ejection seat.
(due to nagging mother-in-law)
over 7000 pages in the FSM, takes long time to scan this.

is this some autel scan tool bull
where it gives an odd code
then you look it up in there silly manual
and find what it really means?

i see one hit, in google for P0300 is true code
why not use a real scan tool and stop fooling about.
or ask any shop in town, no dealer needed. 99% of time.

Apr 22, 2014 | 2007 Jeep Liberty Sport

1 Answer

Where can i find Autosnap A810 OBDII EOBD Scan Tool files free download


I recommend you AUTOSNAP A810 OBDIIEOBD Code Scanner ,here you can find detail information.
If you want to know OBDII tools,you can visit website www.obd2tool.com

Apr 17, 2013 | Audi Cars & Trucks

1 Answer

NEED DRIVE CYCLE FOR 2004 CRV TO RESET CAT AND O2 MONOTOR


Here is the info

NOTE: The ignition key must not be on prior to the cold start otherwise the heated oxygen sensor diagnostic may not run.

1. As soon as the engine starts, idle the engine in drive for two and a half minutes with the A/C and rear defrost on. OBDII checks oxygen sensor heater circuits, air pump and EVAP purge.

2. Turn the A/C and rear defrost off, and accelerate to 55 mph at half throttle. OBDII checks for ignition misfire, fuel trim and canister purge.

3. Hold at a steady state speed of 55 mph for three minutes.

OBDII monitors EGR, air pump, O2 sensors and canister purge.

4. Decelerate (coast down) to 20 mph without braking or depressing the clutch. OBDII checks EGR and purge functions.

5. Accelerate back to 55 to 60 mph at half throttle. OBDII checks misfire, fuel trim and purge again.

6. Hold at a steady speed of 55 to 60 mph for five minutes.

OBDII monitors catalytic converter efficiency, misfire, EGR, fuel trim, oxygen sensors and purge functions.

7. Decelerate (coast down) to a stop without braking. OBDII makes a final check of EGR and canister purge.

Oct 02, 2010 | 2004 Honda CR-V

2 Answers

Reset computer in doege stratus wont pass inspection drove 50 miles and computer still didnt reset help


U have to operate the engine at all kinds of diff speeds and drive modes, it is called a OBDII drive cycle, here is how u do one.
1. As soon as the engine starts, idle the engine in drive for two and a half minutes with the A/C and rear defrost on. OBDII checks oxygen sensor heater circuits, air pump and EVAP purge.

2. Turn the A/C and rear defrost off, and accelerate to 55 mph at half throttle. OBDII checks for ignition misfire, fuel2_bing.gif trim and canister purge.

3. Hold at a steady state speed of 55 mph for three minutes.

OBDII monitors EGR, air pump, O2 sensors and canister purge.

4. Decelerate (coast down) to 20 mph without braking or depressing the clutch. OBDII checks EGR and purge functions.

5. Accelerate back to 55 to 60 mph at half throttle. OBDII checks misfire, fuel trim and purge again.

6. Hold at a steady speed of 55 to 60 mph for five minutes.

OBDII monitors catalytic converter efficiency, misfire, EGR, fuel trim, oxygen sensors and purge functions.

7. Decelerate (coast down) to a stop without braking. OBDII makes a final check of EGR and canister purge

Jun 02, 2010 | 2004 Dodge Stratus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

113 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...