Question about Audi 100

Open Question

Audi 100 c3 gear selector diagram

The gear selectors bushes are worn, only 3rd & 4th gear, no reverse and 5th

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 288 Answers

SOURCE: cant find 5th r reverse, transit

recheck for proper cable adjustments 5 -rev

Posted on Dec 13, 2008

  • 1 Answer

SOURCE: Broken Linkage on a Manual Transmission?

what kind of vehicle is it?

Posted on Dec 15, 2008

  • 255 Answers

SOURCE: just bought the car cheap and the gear stick is 5

On these WC Volkswagens, you have to make sure that the little ball-and-socket gear linkages are connected. If one is off, replace it with new, because the old one will probably pop off again. If there is no problem there and you can select 5th gear, and then only later does it "pop out" of gear, then the spline lock rings have worn where the mating surfaces of each spline tip don't provide a positive "lock" when under power. Some folks think that when a transmission "pops out" when driving, it is the syncronizers. This is never true. (Even Click and Clack get this one wrong continuously.) The syncronizers are responsible for clashing gears during the gear selecting action.
A transmission rebuild is in order if the thing pops out of gear. Good luck.

Posted on Feb 26, 2010

  • 480 Answers

SOURCE: 5th gear went out yesterday

time to put a new tranny in that jet most of the time it costs to much to repair it then replace it i have done may tranny rebuilds and replacements to me i would just tell you to replace it at least you will get a better warrentee and stuff

Posted on Feb 27, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My car doesnt come out of 5th gear. At first it wouldnt come out of 3rd and when i tried to put it into 4th it wouldn't go in at all but it did go into 5th and stayed there. What the problem?


pull the gear stick out of the top of the box by undoing the turret section and look at the selector rails and gate
if you can move them with a big lever ok then check the pivot of the gear stick
if it is a column shift operation then check all the linkage and bushes and adjust any that need it

Jul 14, 2015 | Cars & Trucks

1 Answer

2001 Hyundai Tiburon will not go into 5th or reverse, however it will go into gear 1 to 4


5th and reverse gears are on the same selector rail. It is possible that the selector fork has come loose for the 5th gear or reverse. Remove the gear lever turret section of the box and see if the selector rail is moving gears or the rail itself.

Dec 08, 2014 | 2001 Hyundai Tiburon

1 Answer

KIA K2900 won't go into 1st, 3rd and 5th gear


. If the box has been performing as expected and this has just started ( manual box ) I would be checking the gear selector either on the side of the box -- in the selector levers or in the cable operation. As the movement for all three gears is in a forward direction and you may have a cable operation to select the gears check the cable for failure. It the selection is at the base of a steering column then check for failed bushes and if it is a top mounted lever directly into the gear box then check that the pin that pivots the gear lever is tight and not worn. I am reasonable confident that the problem is in the selection mechanism and not in the box proper.

Jan 28, 2014 | Kia Cars & Trucks

1 Answer

1986 mazda 323Lx gears disappear


Sounds like you have worn gearbox selector linkages and I suggest that you get someone to take a look at them PRONTO.

Jan 19, 2013 | 1986 Mazda 323

1 Answer

Ford focus gear kinkage


Worn bushings, bent shift lever, Broken engine mount is a possibility

Dec 18, 2011 | 2003 Ford Focus

1 Answer

All gears can be selected accept 5th while driving or standing still


Your linkages are probably worn, there are a whole lot of bushes that join the linkages from the gear lever to the transmission. you could try and adjust the gear lever over to the left but then you are probably going to hassel to select reverse. to have the selector bushes done is really cheap and and really quick to have done, then it'll be good as new again.

Feb 21, 2011 | 1985 Volkswagen GTI

1 Answer

93 toyota pickup. 4 cylinder, 5 speed manual 98k. ...


possible selector linkage adjustment , loose or shifted

Jul 02, 2017 | Cars & Trucks

1 Answer

Just fitted two new gear selector cables to my transit van but now cant engage reverse


i can get 1st 3rd and 5th but can not get 2rd 4th or reverse can any one help

Oct 16, 2009 | 2003 Ford Taurus

1 Answer

Cant find 5th r reverse, transit


recheck for proper cable adjustments 5 -rev

Nov 28, 2008 | 2000 Ford Expedition

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75051 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14200 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...