Question about 1998 Isuzu Rodeo

2 Answers

How to remove starter from 1998 isuzu rodeo 4 whl drive 6 cyl?

Starter is bad and needs to be replaced. would like to know appropriate procedure. Thank you!

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 159 Answers

Disconnect the battery first. remove the 3 bolts connecting the starter the the bellhouseing, the remove the wires. install in reverse order

Posted on Jun 04, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

This guy left a lot out. First you must remove 3 nuts that connect the exaust to the manifold. Next you must remove the nut and bolt at the first union. Now you can remove the starter and reinstall a new one. Now just attach the exaust and problem solved.

Posted on Sep 08, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Cts03 3.2 What's the best way to get to starter?


Jack the vehicle up an crawl underneath on the passenger side ! Don't forget to disconnect the negative battery cable .
Removal Procedure
  1. Remove the starter heat shield. Refer to Starter Shield Replacement .
  2. Remove the right side engine mount bracket. Refer to Engine Mount Bracket Replacement - Right Side .
Engine Mount Bracket Replacement - Right Side
Removal Procedure
  1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  2. Remove the right catalytic converter. Refer to Catalytic Converter Replacement - Right Side in Engine Exhaust.
  3. Remove the starter motor heat shield. Refer to Starter Shield Replacement in Engine Electrical.
  4. Install a screw jack with a block of wood under the oil pan for support.
    showgif.do?image=816388
  5. tif.gif
  6. Remove the right engine mount upper retaining nut.
A lot of work !!!!!! Taking to a qualified repair shop mite be worth it .
Labor $174 - $222

Sep 19, 2016 | Cadillac CTS Cars & Trucks

2 Answers

I changed the battery in my 2006 f150 and now it won't start, and i hear a clicking noise in fuse box


Its possible that you have armed the passlokc or immobilizer system; check in the owners manual de reset or disarm procedure.

Other possibilities, starter or ignition switch go to bad.

Keep us updated.

Jan 20, 2011 | Ford F-150 Cars & Trucks

1 Answer

TURNING KEY TO START 2004 SATURN VUE. MUST TRY MULTIPLE TIMES IN ORDER FOR THE VEHICLE TO START. REPLACED THE BATTERY STILL HAVE PROBLEM. WHEN TAKEN TO AUTO REPAIR SHOP THEY CANNOT FIND PROBLEM..NEED HELP


you may have a bad starter relay, or bad starter colenoid, best solution, have starter relay checked, if good, replace starter, does it click when you try to start?but won't? clicking indicates bad battery connections, bad starter colenoid, or simply bad starter. sometimes it's better to replace the whole starter, considering how much it costs to check all the above. suggest that you have battery checked for free at autozone or advance automotive for free. if battery checks good, replace starter. if you accept my solution and it works, let me know via fixya.com and thank you for choosing fixya.com

Dec 30, 2010 | 2004 Saturn VUE

1 Answer

I have a 92 buick skylark 3.3. v6 that I just replaced the starter on after the original starter gave out...after 3 days it's acting like the starter is junk already...I need to know if there's an inline...


MAKE SURE ALL CONNECTORS TO THE STARTER ARE TORQUED TO THE PROPER SPECIFICATIONS IF THEY ARE CHECK RING GEAR ON TORQUE CONVERTER> MAY HAVE MISSING TEETH ON RING GEAR!

Dec 15, 2010 | 1992 Buick Skylark

1 Answer

Low oil pressure light comes on and engine won't turn over. Everything else works but no power going to starter. Wait about one hour and a half and it starts fine. Oil level is OK. Is there an oil...


Welcome to FIxYa.com





First thing to do is check the power to starter with a volt meter.

A. From the battery to starter positive cable check to see if you have continuity.

B. Check the voltage at starter. Red lead of tester to the positive connection and the black lead from meter to a good ground.

Results should be: A. continuity And B. !2 volts

If the results of the above or not what your results are then stop and write to me. If your results are as above continue on to the second test.

Second thing i need you to do is get a Hammer

Now do you know where the starter is ? OK (see diagram)

you will need someone to help you- have this person get in the truck key in ignition -- you go to starter hammer ready holler START ENGINE then tap on the starter with hammer. Will it start?

Now tap the solenoid . It is the little round container on top of starter tap that too. Will it start?

This is an easy way to see if the truck starts if so starter is bad.

leedavidian_37.png

Ok We have a service Bulletin on this model for no crank .


TSB 06-19-14

100206

NO CRANK: STARTER TERMINAL FATIGUE

FORD:

1997-2007 Crown Victoria

1997-2004 F-150 Heritage

1997-2006 Expedition

1998-2006 E-S e?es

1999-2006 F-Super Duty

2002-2007 Explorer

2004-2006 F-150

2007 Explorer Sport Trac

LINCOLN:

1998-2006 Navigator

2003-2005 Aviator

MERCURY:

1997-2007 Grand Marquis

2002-2007 Mountaineer

ISSUE

Some vehicles may exhibit a no crank condition due to an open circuit in the starter relay

to starter motor circuit at the starter motor connection.

ACTION

Follow the Service Procedure steps to correct the condition.

SERVICE PROCEDURE

A new starter terminal wiring pigtail kit is released eliminating the need to replace the

entire harness for the terminal connection.

NOTE

TERI?INAL Kit ONLY SERVICES THE STARTER RELAY TO STARTER MOTOR

CIRCUIT. THE KIT DOES NOT SERVICE STARTER MOTOR BAHERY POWER

Circuit.

Refer to instruction sheet contained in Wiring Pigtail Kit for wiring harness service

procedure.

NOTE

REFERENCE THE APPROPRIATE WORKSHOP MANUAL SERVICE SECTION 303-06

FOR REMOVAL AND INSTALLATION OF THE STARTER MOTOR WIRING

TER1•fiNAL CONNECTION PROCEDURES.

Image

Parts Block

WARRANTY STATUS: Eligible under Provisions of New Vehicle Limited Warranty

Coverage

OPERATION DESCRIPTION TII?

06l9l4A Install Wiring Pigtail kit (Do 0.4 Hr.

Not Use With 14200A)

MT061914 Claim Additional Labor Actual

Required As Actual Time

Or Use SLTS Operation If

Available

DEALER CODING

CONDITION

BASIC PART NO. CODE

14A280 01

Disclaimer



leedavidian_38.png

Thank you for using FixYa.com

Regards, Lee Davidian

Nov 07, 2010 | 2003 Lincoln Navigator

1 Answer

I need a picture for wiring the silanoied on ford mustang 302 v8 fuel injected


Testing Use the charts to help located and diagnosis starting system problems. Remember that the starter uses large amounts of current during operation, so use all appropriate precautions during testing. Fig. 1: Starter circuit 88152ga5.gif
Fig. 2: System inspection chart 88152ga6.gif
Fig. 3: Evaluations procedure charts 88152ga7.gif
prev.gif next.gif

Oct 28, 2010 | 1992 Ford Mustang

1 Answer

Key turns in ignition but nothing happens battery good and lights come on do i need a new starter and how do i get to it to remove old one


First troubleshoot. Have to tried jumping the car? Are the battery terminals clean and tight? If all this is good, you can try jumping the solenoid to see if the starter/solenoid is bad. I have posted procedures at http://www.fixya.com/cars/r5821173-doesnt_car_start_gasoline_engines.

Please let me know if you have questions. If you decide the starter is bad, there are instructions here for replacing it: http://www.fixya.com/cars/r5973094-starter_replace

Sep 25, 2010 | 1996 Nissan Sentra

1 Answer

Need procedure to replace starter


there is two bolts on the starter you will have to remove them but before doing anything disconnect battery so you don't short anything out. there is a red wire on starter that will have to come off to. when you take the two bolts out the starter should pull right out if not use a screw drive to help it. It is really easy I hope this helps.

May 04, 2009 | 1998 Buick LeSabre

1 Answer

Starting my vs40 volvo


trun the key with your foot off the acclerator. but that should have no bearing on starter failure . why have you replaced the starter have you checked the connection to make sure they are tight . when you have replaced the starter have you checked the ring gear for wear. and is the starter installed correctlykdc744

Feb 08, 2009 | 2000 Volvo S40

2 Answers

Starter problems


Try to check battery. If it is fully charged it might be still starter.
Beacause you used rebuilt starter. For most Acura, Honda, Toyota
using rebuilt starter is not appropriate as it wont do the same job as brand new. You have to use brand new.
Good Luck

Jan 14, 2009 | 1997 Acura TL Series

Not finding what you are looking for?
1998 Isuzu Rodeo Logo

1,066 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

80339 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14417 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...