Question about 2002 Hyundai Accent

1 Answer

I want to chang the rear brake ! so how do i get to the brake or what do i need to get the dum off !

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 142 Answers

Remove the rear wheel. Check the studs to see if it has any retaining rings on them. If they do, pry them off with a small screwdriver.
Now take a hammer and bang the drum to loosen it off the axel flange and pull the drum off.

Posted on Jun 04, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do you remove the rear dums on a 2001 Oldsmobile mini van?

with every thing out of the way and you don`t have a torch to warm the drums, take a hammer and hit the drum between the wheel studs hard this should pop the drums loose, what happens is they get rusted/corroded to the hub assembly and need help to get loose.

Jul 13, 2014 | 2001 Oldsmobile Silhouette

1 Answer

Can not get rear break dums off

to try and get the rear brake drums off first try to knock the drum off with a hammer and hit the center area around the hub area not the studs. by doing this you will be vibrating the drum and it might free itself off or if this does not work then at the back of the drum there is an access hole take the rubber plug out and turn the adjuster to slack off the brakes so you could get the drum off

May 30, 2011 | 2001 Ford Windstar

1 Answer

Rear brake shudder, even with new drums fitted

the shoes may be misadjusted, try jacking it up, and with emergency brake off turn the wheels to see if they freewheel or if they drag-pull the dums off and make sure the shoes are centered on the backing plate, then install the drums again. if they drag, use a screwdriver or star wheel adjusting tool to back the shoes off a little bit.

Mar 16, 2011 | 1991 Toyota Camry

1 Answer

1997 Jeep Grand Cherokee Brake Problem. Brake Pedal Falls To The Floor. Calipers were replaced twice,master cylinder,brake hoses and pads. Systemm has been bleed numerous times - no air but the brake...

This may sound dum but its been done a few times and is a simple mistake , the bleeder screw is up top, with the caliper on the bleeder screw should be up top, if not then calipers are on the wrong side, it sounds like air in the system, also you pumped the pedal up to push out the piston so pads hit rotor after bleeding,i dont see anything else, if the pedal is good with pinched lines at caliper then it got to be calipers are wrong or on the wrong side and the bleeder is not atop caliper,also you bleed the rear also? these trucks and cars use left caliper and rt rear on one system of the master and rt front and left rear on one side, let me know about the caliper, heres a picture to show you what i mean. hope this helpsjohnjohn2_23.jpg

Nov 16, 2010 | 1997 Jeep Grand Cherokee

2 Answers

Does the 2003 gmc yukon have rear rotors? and do the brakes need to be changed if the rotors need to be machined?

Yes, it has rear Disc Brakes, I would suggest to change the rear pads since they have to remove the rear Brake Calipers to remove the rotors and it wouldn't take much more time or labor to replace the pads at that point. That way when your rear rotors are re-installed and your new brake pads are installed your rear brakes should give you longer service life and better stopping power.

Jun 04, 2010 | 2003 GMC Yukon

1 Answer

Daewoo lanos

your brakes are keeping i on the dum try a puller and a hammer

Oct 18, 2008 | 1999 Daewoo Lanos

1 Answer


Take it to a mechanic and have them check for a vacuum leak.

Sep 21, 2008 | 1997 Mazda 626

Not finding what you are looking for?
2002 Hyundai Accent Logo

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts


Level 3 Expert

80407 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides