Question about 1993 Jaguar XJ6

1 Answer

Won't start car won't start rotate but no fire up

Posted by on

  • miamishark Jun 05, 2009

    I did and is ok .I change the fuel pump,the coil ,the crankshaf position sensor, check the computer check for compresion 170 180,check the check the injectors ok, I add some fuel starter ,check the relays ,spark plug good spark is getting all the power .crank but won't start



1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 51 Answers

Check the cap and rotor and the coil other than this im not sure what else it could be

Posted on Jun 04, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

1992 Ramcharger We have no spark no fuel. Checked continuity from computer to sensors and installed new sensors still won't fire HELP

ok if its not the crankshaft sensor or pick up plate.
then look at your asd relay. cpu controlled via ground.
no fuel or fire. means pcm is not detecting engine rotation.
I remember bypassin the pcm ground control on some. just install
a switch to operate it.

Feb 15, 2013 | 1992 Dodge Ramcharger

1 Answer

Car won't start 2003 Dodge Stratus sxt coupe cranks but won't start what could b the problem? I tried spraying starting fluid in the air system but it still won't start!

i would check and see if spark pluges are firing. you can take one out and plug into spark plug wire then let the bottom of the plug sit on engine and get someone to try to start while you look at the plug to see if there is any fire. if you have no fire or fuel it would be the crankshaft sencer. it could be the timing belt but the motor would sound different turning over then it used to.

Dec 22, 2012 | Cars & Trucks

1 Answer

Jeep was running had a miss. I noticed the fireing order on dist. was wrong. I wired it as 1-3-4-2 and now it won't even try to star. It justs backfire I put new spark plugs, thoroughly cleaned

could well be 180 deg out and check dissy rotation that tyou have set plug leeds in right order and going the right way and starting at the right place no 1 tdc firing not exhaust

Nov 29, 2012 | 1985 Jeep Cherokee

1 Answer

I have a 1996 dodge caravan (3.3L) that won,t start.I had diagnostic test done and it showed a bad crankshaft sensor.I replaced it and it still did'nt start so i went ahead and replaced the cam sensor and...

Typically, the on board computer monitors the crankshaft for rotation and the cam shaft for rotation, and fires the spark plug accordingly. There may also be a sensor for top dead center for cylinder number one. If you have a broken, or slipped timing belt/chain, the rotation sensors will be out of sync and the computer won't let the spark plugs fire. You could also have a failed ignition coil for a failed trigger circuit for you coil. If the diagnostics are not calling out a specific trouble code, check your timing/belt.
Note that I am not an expert on this particular vehicle, but have spent a fair amount of time working on newer computerized vehicles.

Jan 17, 2011 | Dodge Caravan Cars & Trucks

2 Answers

Spark plug wiring diagram for 98 tahoe car is missing need to know which wire goes were

You didn't post your engine size so please pick the applicable diagram:

1996-98 4.3L Engines Firing Order: 1-6-5-4-3-2Distributor Rotation: Clockwise

1996-98 5.0L, 5.7L and 7.4L Engines Firing Order: 1-8-4-3-6-5-7-2Distributor Rotation: Clockwise

4.3L Engines Firing order: 1-6-5-4-3-2 Distributor rotation: Clockwise

4.8L, 5.3L and 6.0L Engines Firing order: 1-8-7-2-6-5-4-3 Distributorless ignition system (one coil on each cylinder)

5.0L, 5.7L and 7.4L Engines Firing order: 1-8-4-3-6-5-7-2 Distributor rotation: Clockwise

Feb 14, 2010 | 1998 Chevrolet Tahoe

1 Answer

Motor rotates but appears to be no fire

If the electronics have been cut up it could be anything, also the electronic Qjet does not flow enough for a 355CI V8, I know this from hard won experience on my 82 trans am

Nov 15, 2008 | 1985 Pontiac Firebird

1 Answer

Car will not start

If I am right, the firing order is,1-3-4-2. With the dissy cap removed, have someone turn the engine over so you can see which way the rotor arm goes. Set the engine to TDC and the rotor arm should point to the No1 cylinder at the start of the firing order. If it rotor points away from the No 1 cylinder then slacken the dissy housing and move the diddy until the rotor ppoints to the No1 cylinder. Now pHT lead from the No1 spark plug to the No 1 possition on the dissy cap. The next lead goes on the next available possition on the dissy cap in the way of the rotation of the rotor then to the No3 spark plug carry on the same with 2 and 4 and that should solve your problem unless you have a different firing order.

Sep 21, 2008 | 1990 Volkswagen Golf

Not finding what you are looking for?
1993 Jaguar XJ6 Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers


Level 3 Expert

76109 Answers


Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides