Question about 2000 Mazda 626

2 Answers

Hi i have a 2000 mazda 626 the a/c has stopped working the light is on but no cold air comes out any ideas ??

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 27 Answers

First note if your ac compressor is working, if not check your fuses or ac relay. Hope this helps

Posted on Jul 01, 2009

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 296 Answers

Hi
i would suggest replacing the T.X valve, as that way you wont have to de commission the system again and repair the system and then regas, as this can prove costly. In relation to the guages normally the Low side (blue)on the guage will read between 8-10 o'clock approxiamately, and the high side will read between 11.30 and 13.00 approxiamately, now when if the TX valve is blocked your LOW side will back up and read much higher, in the area of 11.30 and 13.00 approx or even higher and your high side as high or potentially higher, basically the scales will read excessive levels on both sides.
As the Gas is poisonous (cancerous) you will need to have this properly degassed and recovered, with the correct equipment, then while the repair is being carried out ensure that all pipe openings are sealed, as the reciever drier will require replacement also if exposed to atmosphere for any longer than 5-10 minutes, as it will become internally damaged, in addition to this any exposed "O-rings" will have to be replaced and new seals pre-lubed with denso-8 air con oil to ensure a correct vacuum seal when the vacuum evacuation process is carried out.
Then once all sealed all atmosprhere will have to be sucked out so that you have a vacuum, this is where the guages come in handy, then if it holds solid vacuum on both guages for approxiamately 10 mins with the evacuator switched off all is ok, is not then you will need to investigate for any possible leaks, if all ok regas with the recommended gas amount and all should be good.

OR

chek this sites to ve a detailed idea to solve your problem
http://www.myhonestmechanic.com/articles/mazda-626-ac.shtml

plz do let me kno,if this solution worked for u or not,so tht i can further research on your prob
all the best
regards

Posted on Jun 04, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2000 mazda 626 and my air conditioning is not getting cold. The freon is full in the car.the car smokes at a red light when just sitting there while air is on. Wht could be the problem?


Is it possible that the clutch on the compressor is not engaging or the compressor itself is locked up. When you turn on the air, does the engine bog down noticeably? If so one of the two above are likely.

Jun 06, 2015 | 2000 Mazda 626

1 Answer

1993 mazda 626 auto, starts fine when cold, but not when I've driven it for a while.


I would start with a good tune up, including the intake gasket. Changes in temperature could cause gaskets to stop sealing properly letting unmeasured air inside the engine. Also check for fuel filter.

Mar 26, 2013 | 1993 Mazda 626

1 Answer

2000 mazda 626 wont blow cold air i have replaced compressor dryer and flushed the system and reinstalled new freon any ideas


There is a valve that stops hot coolant from entering the heater box. It is probably stuck open. murf427

Aug 29, 2012 | 2000 Mazda 626

1 Answer

Can't find low side port for 2000 mazda 626


from compressor trace large diameter line until you see port cap may be marked with L, if a/c is working low side line will be cold or cool, highside will be warm

Jul 15, 2012 | 2000 Mazda 626

1 Answer

When i shut off car fan still stays running. i have 2000 mazda 626


Hello, this was common in some vehicles, the fan would cool down the motor and than cut out when the vehicle was switched off. It was actually a quite good idea because when you switch the motor off, the water pump stops working and there is no air flow to the radiator and engine, which makes the engine temperature higher, the fan just cools it down, just make sure it does cut out after a couple of minutes.

Feb 20, 2011 | 2000 Mazda 626

1 Answer

2000 mazda 626 check engine light went on . code


probley not egr valve it probley egr control solenoid or wiring

Apr 11, 2010 | 2000 Mazda 626

2 Answers

Mazda 626 2000 - warning lights for ABS, TCS


what u do to stop the vehicle and remove the battery head and refix,if the problem still persits go for thorough scanning.

Mar 25, 2010 | 2002 Mazda 626

1 Answer

Car accelerated to 4000 to 5000 rpm by itself.


could be a sensor problem in your catalytic convertor or air mass meter.

Aug 08, 2009 | 2000 Mazda 626

1 Answer

2000 mazda 626 when I open the door the open door


do you have air assisted heradlights might have a short feel the wires for hear be carefull not to hurt yourself.

Jul 30, 2009 | Mazda 626 Cars & Trucks

4 Answers

Mazda 626 engine cut off when excel over 3000 rmp


my 1988 mazda 626 starts okay then dies everytime it idles down to normal idle speed. i replaced the throttle control sensor and the mass air sensor. i replaced the rotor in the distributor but is still dies. if you throttle up to about 1500 rpm it keeps running. any ideas???

Aug 04, 2008 | 1994 Mazda 626

Not finding what you are looking for?
2000 Mazda 626 Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8582 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...