Question about 2007 Chevrolet Avalanche LTZ

1 Answer

I have an 2008 4x4 avalanche, I need to replace

I have an 2007 4x4 avalanche, I need to replace the Rotors, but the braket covering the rotor, I can not loosen the bolts o remove this, I broke sockets and breaker bar. Does this braket not come off or am I missing something ?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 206 Answers

It will come off try heating the area where the thread is with a small hand held torch it probably has loctite on it get the thread area hot and it should come out.

Posted on Jun 05, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What size tool/kind of tool do i need to remove the big center star nut on my 2007 toyota highlander front rotor

The rotors are knock off rotors. They are just rusted and stuck to the hub. DO NOT REMOVE THE AXLE NUT. this will not help you get the rotor off. Instead use a large hammer and hit the rotor from the back side. Several good whacks should break it free.

Apr 20, 2014 | 2007 Toyota Highlander Hybrid

1 Answer

Car problems

Did your replace your caliper brakets, make sure your pins move freelly no rip dust boots and your pads slide nicelly in brakets if doesnt fix your problem try replacing brake hose may be colapsed and holding back pressure.

Jul 22, 2012 | 2004 Toyota Camry

1 Answer

Do you have to take the hub off on a brake job for a avalanche 2003 4 wheel drive

To do a brake job front or rear there is no need to remove the "hubs" the front and rear rotors or rear drums are knock offs. if they are stuck to the hub a couple of gentle hits with a hammer will usually free them up. If you are replacing the rotors than whack away as hard as you would like.

Mar 14, 2012 | 2003 Chevrolet Avalanche

1 Answer

How do you the rotors off to replace them on a 2003 tauras

well if its the front just take lug nuts off pull the wheel off remove caliper and caliper braket and rotor come off

if this helps you please rate me good thanks

May 06, 2011 | Ford Taurus Cars & Trucks

1 Answer

How do i pull the front rotors, they need to be replaced?

start by taking the wheels off then you will have to take the brake callpers off once that has been removed there is a braket that held the callipers on that will need to be removed then the rotors should come off be sure you look for clips on the studs or a philleps screw ma hold them on if not and they still wont move you might have to beat on them with a hammer becareful not to hit the studs dont be affraid to hit them hard

Feb 27, 2011 | 1992 Honda Accord

2 Answers

How difficult is it to cange the front rotors?

depending if you have the tools to do the job and pb blaster lock tite and white and dark grease for a beginer it has a rating of 7-8. if you work on cars and know what your doing, then its easy.. first thing is to remove the calapers then remove the calaper mounting bracket spray around the studs and bolts with pb blaster also around the hub and tap around the whole area around rotor dont hit the studs (with hammer) to break the rust buildup this should break rotor free then you may want to clean the rust off so that the rotors seat properly remove and clean new rotors with brake cleaner to get off the film off them (shipping rust retardent) and wipe. spray bolt holes to clear any rust left while removing old rotor and braket and dry. place a small ring of lock tite on bolts holding caliper brackets and let stand till harden or almost hard. replace new rotors install bracket/s and bolts (torq to ? 80foot lb) while replacing rotors replace brake pads, replacing just rotors will over heat new rotors in spots and warp rotors!!! make sure you pull the pins that retain the calipers to the bracket and add light coat of white grease to pins so calipers slides easy and evenly

Jan 21, 2010 | 2003 GMC Envoy

2 Answers

How to remove the rear rotors on a gmc 2002 2500 hd extra cab 4x4

The rotors are one with the hub.s, So, you need to pull the axles , hub bearings. Good Luck

Sep 18, 2009 | 2002 GMC Sierra 2500HD

1 Answer

07 Chevy Avalanche Brake Wobble

I would have someone check out the rotors for you.

Apr 08, 2009 | 2007 Chevrolet Avalanche LTZ

1 Answer

I am trying to replace my rear rotors/pads.size of rotors/pads?

Take a tape measure and measure acroos the middle of the rotor, but it should tell you on the rotor what size it is. if push comes to shove take one to the parts store and match it up.

Mar 18, 2009 | 2002 Chevrolet Avalanche

1 Answer

Brakes on my new truck

i think you said it all i agree 100 percent hope it works out for you

May 23, 2008 | 2007 Chevrolet Avalanche LTZ

Not finding what you are looking for?
2007 Chevrolet Avalanche LTZ Logo

Related Topics:

176 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides