Question about BMW 530

1 Answer

How to top up a transmission on e39 bmw - 530 BMW Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 122 Answers

Get car on level ground start engine let warm check fluid level with dip stick while engine is running & fill acorrding trough dip stick port

Posted on Jun 04, 2009

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
motor1258
  • 6674 Answers

SOURCE: put in a new wiper motor 1997 e39 528i bmw\it stops in the middle

Remove arm(s), put wiper motor in park,(shut off) then re-install arm at base of windshield where they were before,when shut off.(in park position.)

Posted on Sep 26, 2009

MNfisherman
  • 11896 Answers

SOURCE: How to install front bumper cover on 2001 BMW E39

Installation of the Molding
Take the Molding Trim whether it is stock black or painted. Mine is black because my car is a year 2000. Painted side moldings were done in the year 2001. Snap them into place.
dscn5738%20copy.jpg 5 Installation of the Rubber Gaskets
From the stock bumper, retrieve the upper rubber gaskets unless you ordered new ones. Simply take a screw driver and pry a corner off to get you started. Wash thoroughly. NOTE which one belongs on which side.
Place the rubber gasket on the M5 Front Bumper onto its appropriate side. Top dscn5717%20copy.jpg The M5 Bumper is now Fully Assembled!!! Place aside where it can't be damaged.

Posted on Nov 15, 2009

tbarratt
  • 96 Answers

SOURCE: Where is the Crank Sensor '99 BMW 523i E39 Auto

are you sure you need the crankshaft position sensor changed. it is at the back of the engine i believe, but.....
check for a wet ecu first... read the note on e36...

the ecu compartment is under the windshield on the passenger side on E36

you gain acess to it under the hood....
this compartment gets wet, the ecu lays on a flat surface in that
compartment.

the bottom side of the circuit board gets wet and starts corrosion.

remove the ecu, take the bottom plate off, clean the bottom of the circuit
board with alcohol and a soft tooth brush.

you should be able to see the signs of corrosion or conductive build up.

this gunk bridges solder points doing all sort s of wierd things to your
car, including false sensor readings from asc/abs controllers and other
sensors....

all the way to engine failure and worst case burnt and shorted wiring
harness.

I'm on my 3rd ecu, took me and the repair boys a few years to figure this
one out.

BTW: i would get that ecu mounted above that flat surface, use some sort
of standoff to raise it so that it is not laying in the wet.

Posted on Feb 07, 2010

  • 105 Answers

SOURCE: i try to go for top speed in my e39 540 i bmw but ...

It's because of your Motronic Unit (the computer) having self-limiters in it. If you want to change your computer's settings, go to www.bavauto.com and they sell "chips" or a programmer to allow you to reach top speeds by bypassing the limiters within your Factory Computer...known to us "Bimmer" enthusiasts as a Motronic.

Hope this Helps,

~00 Buck~

Posted on May 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

BMW e39 1997 fuse F54 in the right rear of trunk for what ?


Hi Ashraf.

Fuse F54 should be rated at 15 amps and it is for the FUEL PUMP

Good information on ALL fuses here

http://fusesdiagram.com/bmw/fuses-and-relay-bmw-5-e39.html

Mar 14, 2017 | BMW Cars & Trucks

1 Answer

Air suspension question is for a BMW e39 528i touring 1998


didn't know there was air suspension on an e39

Jun 10, 2015 | BMW 528i Cars & Trucks

1 Answer

I have a 2005 BMW 745i. It won't come out of park. Someone mentioned that there is not enough pressure because a sealant need to be replaced in the transmission shaft. Is this a costly repair, and will it...


Hi normally most E39/E60 BMW electronic gearboxes have a safety lock connected to foot brake which restricts gear selection unless driver apply;s foot brake.this could be a possible fault ,gear linkage have come loose,otherwise internal gearbox fault ,this will require a full diagnostic fault code report to determine that faults are permanent or intermittent . low transmission oil level can cause this problem.

Jan 07, 2015 | Cars & Trucks

1 Answer

BMW e 39 Free Workshop Manual


BMW 5 Series (E39) Service Manual: 1997-2002
2003 ' Bentley Publishers ' English ' ISBN: 083760317X ' Pages 1002 ' File type: PDF ' 44.37mb

This Bentley Manual is the only comprehensive, single source of service information and specifications for BMW 5 Series (E39) cars from 1997-2002. Whether you're a professional technician or a do-it-yourself BMW owner, this manual will help you understand, maintain, and repair every system on 5 Series cars.

BMW 5 Series (E39) Service Manual: 1997, 1998, 1999, 2000, 2001, 2002
525i, 528i, 530i, 540i Sedan, Sport Wagon.

Jul 29, 2012 | BMW 525i Cars & Trucks

1 Answer

I try to go for top speed in my e39 540 i bmw but it gone only for 210 so why ?


It's because of your Motronic Unit (the computer) having self-limiters in it. If you want to change your computer's settings, go to www.bavauto.com and they sell "chips" or a programmer to allow you to reach top speeds by bypassing the limiters within your Factory Computer...known to us "Bimmer" enthusiasts as a Motronic.

Hope this Helps,

~00 Buck~

May 16, 2010 | Cars & Trucks

1 Answer

How to install front bumper cover on 2001 BMW E39


Installation of the Molding
Take the Molding Trim whether it is stock black or painted. Mine is black because my car is a year 2000. Painted side moldings were done in the year 2001. Snap them into place.
dscn5738%20copy.jpg 5 Installation of the Rubber Gaskets
From the stock bumper, retrieve the upper rubber gaskets unless you ordered new ones. Simply take a screw driver and pry a corner off to get you started. Wash thoroughly. NOTE which one belongs on which side.
Place the rubber gasket on the M5 Front Bumper onto its appropriate side. Top dscn5717%20copy.jpg The M5 Bumper is now Fully Assembled!!! Place aside where it can't be damaged.

Nov 15, 2009 | 2001 BMW 5 Series

1 Answer

Put in a new wiper motor 1997 e39 528i bmw\it stops in the middle


Remove arm(s), put wiper motor in park,(shut off) then re-install arm at base of windshield where they were before,when shut off.(in park position.)

Sep 26, 2009 | 1997 BMW 318

1 Answer

Have a bmw e39 520i '99. Intermittant problem wipers


check the wiper relay on the l/s in negine bay where your engine ecu is fitted it is situated at the bottom and can get in to some water

Jun 05, 2009 | 1999 BMW 5 Series

1 Answer

CRANK SENSOR ON E39 530D


The crank sensor is located on the driver's side of the block where it meets the transmission. It is a few inches below the starter. It is held in place with a 5mm allen bolt.

Feb 22, 2009 | BMW 530 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

307 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...