Question about Chrysler LHS

1 Answer

I have a 1994 chrysler lhs with automatic temperature control...when using the diagnostic mode on automatic temperature control models, code 32 appears indicating blend door stall failure ?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 19,396 Answers

Hi there,

If you get fault code 32 on a Sebring temperature control, that means that the blend door actuator is not working.

Check if there is a 7.5 amp fuse for the blend motor actuator, if there is a fuse test it.
On some model there is no fuse , and the blend actuator is connected straight to the ATC.

Ensure that the blend door is not stuck or broken, by moving in with your hand.

Test the actuator with a multimeter to check if it is getting +5V power. If it is getting power, then replace the actuator, otherwise check wiring and connector.


Posted on Jun 04, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can you tell me the location of code reader 1991 capri ?


1991 is pre-OBD2. code readers will not work.
sorry.
however, all is not lost. Many cars have an alternate way of reading codes from the computer.
Toyota has a block under the hood and you short couple wires together and count engine light flashes
Chrysler you can turn the ignition key on and off a few times and count engine light flashes
in your case for GMs from 1982 to 1995
1: find the 12 pin connector under the dash and short the upper two rightmost terminals.
with the ignition "ON" and engine not running. The system will enter the diagnostic mode. In this mode, the computer will display a Code 12, three consecutive times, by flashing the "CHECK ENGINE", "SERVICE ENGINE SOON" or "MALFUNCTION INDICATOR LAMP" or light. A Code 12 consists of one flash, a short pause, then two flashes in rapid succession.
2:. After Code 12 is displayed, any stored trouble codes will be displayed by flashing the "CHECK ENGINE", "SERVICE ENGINE SOON" or "MALFUNCTION INDICATOR LAMP" light. All codes are displayed 3 times each then a code 12 will repeat. In the diagnostic mode, the computer will also energize all computer controlled relays and solenoids.

Tech -- GM 2 Digit codes for 82 and up (non OBD-II)
code - code definition
12- diagnostic mode
13- 02 sensor or circuit
14- coolant sensor or circuit/ high temp indicated
15- coolant sensor or circuit/ low temp indicated
16- system voltage out of range
19- crankshaft position sensor or circuit
21- throttle position sensor or circuit- voltage high
22- throttle position sensor or circuit- voltage low
23- mixture control (m/c) solenoid or circuit (carbureted models)
23- manifold air temperature (mat) sensor or circuit (1990 and earlier models)
23- intake air temperature (iat) sensor circuit (fuel-injected models)
24- vehicle speed sensor (vss) or circuit
25- manifold air temperature (mat) sensor or circuit - high temperature indicated (1990 and earlier models)
25- intake air temperature (iat) sensor or circuit - high temperature indicated (1991 and later models)
26- quad driver module circuit
27- quad driver module circuit
28- quad driver module circuit
29- quad driver module circuit
31- park/neutral position (pnp) switch circuit
32- baro sensor or circuit (carbureted models)
32- egr circuit (fuel-injected models)
33- manifold absolute pressure (map sensor signal voltage high
33- mass air flow (maf) sensor or circuit - excessive airflow indicated
34- manifold absolute pressure (map) sensor signal voltage low 34- mass air flow (maf) sensor signal - low airflow indicated
35- idle speed control (isc) switch or circuit (shorted) (carbureted models)
35- idle air control (iac) valve/ circuit
38- brake switch circuit
39- torque converter clutch (tcc) circuit
41- no distributor signals to ecm, or faulty ignition module ( carbed models)
41- cylinders select error- mem-cal or ecm problem ( fuel-injected models
41- cam sensor circuit (3.8 engine)
42- bypass or electronic spark timing (est) circuit
43- low voltage at ecm terminal l (carbureted models)
43- knock sensor circuit
44- oxygen sensor or circuit - lean exhaust detected
45- oxygen sensor or circuit - rich exhaust detected
46- power steering pressure switch circuit
48- misfire diagnosis
51- prom, mem-cal or ecm problem
52- calpak or ecm problem
53- egr fault (carbureted models only)
53- system over-voltage (ecm over 17.7 volts)
54- mixture control (m/c) solenoid or circuit (carbureted models)
54- fuel pump circuit (1986 and later models)
55- oxygen sensor circuit or ecm
55- fuel lean monitor (2.2l engine)
61- oxygen sensor signal faulty (possible contaminated sensor)
62- transaxle gear switch signal circuits
63- manifold absolute pressure (map) sensor voltage high (low vacuum detected)
64- manifold absolute pressure (map) sensor voltage low (high vacuum detected)
66- pressure sensor or circuit air conditioning

May 20, 2014 | 2002 Subaru Forester

1 Answer

How to diagnose a non functing Automatic Temperature Control (ATC)


that will be a dealer service issue.. they can assist with this one..

Dec 23, 2013 | 1994 Chrysler Concorde

1 Answer

Hello I have a 1994 maxima manual transmision,it have a check engine light on,when I start the car and beguin to drive it,runs perfect the a few minutes later the car gets very lazy almost want to turn...


Hello! I'll need the trouble code to fix your vehicle...Below is procedure with a code list...Guru...saailer

Remove the trim panels in front of the center console. Locate the engine computer attached to a floor-mounted bracket on the transmission tunnel between the console and the firewall.

  • Turn the diagnostic mode selector, located in a round opening on the side of the engine computer, until it stops. Observe the small red and green LED lights on the side of the computer next to the mode selector. They will flash to indicate the modes, with a pause between each mode. One quick flash is mode one, two quick flashes is mode two and so on. When the light flashes indicate mode three, quickly turn the mode selector counterclockwise until it stops. You have entered mode three diagnostics.

  • Remove the trim panels in front of the center console. Locate the engine computer attached to a floor-mounted bracket on the transmission tunnel between the console and the firewall.

  • Turn the diagnostic mode selector, located in a round opening on the side of the engine computer, until it stops. Observe the small red and green LED lights on the side of the computer next to the mode selector. They will flash to indicate the modes, with a pause between each mode. One quick flash is mode one, two quick flashes is mode two and so on. When the light flashes indicate mode three, quickly turn the mode selector counterclockwise until it stops. You have entered mode three diagnostics.
  • Turn the diagnostic mode selector, located in a round opening on the side of the engine computer, until it stops. Observe the small red and green LED lights on the side of the computer next to the mode selector. They will flash to indicate the modes, with a pause between each mode. One quick flash is mode one, two quick flashes is mode two and so on. When the light flashes indicate mode three, quickly turn the mode selector counterclockwise until it stops. You have entered mode three diagnostics.Observe the red and green LED lights on the side of the computer. The red light flashes to indicate the "Tens" digit of the code and the green light flashes to indicate the "Ones" digit of the code. For example, if the red light flashes two times and the green light flashes seven times, this would indicate code 27.


    Turn the ignition key off for two minutes to exit diagnostics. The computer will automatically return to mode one for normal operation...

    Code 11 Crank sensor angle

    Code 12 Mass airflow sensor

    Code 13 Engine coolant temperature sensor

    Code 14 Vehicle speed sensor

    Code 21 No ignition reference

    Code 22 Fuel pump

    Code 31 Engine control unit

    Code 32 EGR sensor

    Code 33 Oxygen sensor

    Code 34 Knock sensor

    Code 35 EGR temperature sensor

    Code 43 Throttle position sensor

    Code 45 Injector leak

    Code 51 Injector circuit

    Code 54 Automatic transmission signal

    Code 55 No malfunction recorded

    May 04, 2012 | 1994 Nissan Maxima

    1 Answer

    My 1994 Chrysler LHS has a problem with the airconditioning. When it is below 100o it cools fine but when it gets hot it only blows hot air. What can I do to fix this problem?


    You need to refill the refrigerant to the proper level and in accordance to the ambient air temperature outside where your vehicle is located.


    Good Luck and Happy Motoring

    Respectfully

    Jun 21, 2011 | 1994 Chrysler LHS

    1 Answer

    Reset climate control on 1994 chrysler lhs


    The Temperature Control Head is the unit in the dash that displays temperature and status of the climate control system. This unit is known to fail. I replaced mine with another one--used--and it solved the problem.

    Aug 07, 2010 | 1994 Chrysler LHS

    2 Answers

    In a 94' Chrysler LHS what is the firing order? Took the plug wires off the housing unit.


    1994 Chrysler LHS
    3.5 liter SOHC V-6 VIN "F"56539136.gifI HOPE THIS IS WHAT YOU NEED. THANKS FOR USING FIX-YA. PLEASE KEEP ME POSTED. FEEL FREE TO COMMENT ON THE ASSISTANCE

    Sep 06, 2009 | 1994 Chrysler LHS

    1 Answer

    The car keeps coming up a code 23 on a 1999 chrysler 300 for the


    Code 23= Blend door feedback control


    On cars with automatic climate control: To enter diagnostic mode, set the temperature to 75F, press the the off button. Press Floor, Defrost\Floor, Front Defrost simutaneously for 3 seconds until the temperature display begins to flash.
    On cars without automatic climate control, set the blower to any speed, turn the temperature control in between warm and cold. Press Floor, Defrost\Floor, and Front Defrost. All codes will flash via the Front Defrost button.
    When the test is over all fault codes will be displayed (on cars without automatic climate control, they will be blinked out on the Front Defrost button).
    Code Action
    23 Blend door feedback control
    24 ATC mode door feedback failure
    25 Ambient temperture sensor failure
    26 ATC in-car sensor
    27 Sun sensor failure
    31 ATC recirculate door stall failure
    32 ATC blend door failure
    33 ATC mode door stall failure
    34 Engine temperture sense failure
    35 Evap temperature sense failure
    36 ATC head command failure

    Mar 23, 2009 | 1999 Chrysler 300M

    1 Answer

    97 chrylser LHS codes 32, 43


    32 is EGR valve malfunction
    43 is ignition control circuit or spark interface circuit malfunction

    Feb 01, 2009 | 1997 Chrysler LHS

    1 Answer

    Chrysler lhs 3.5 engine


    It sounds like it is in limp mode. This is to protect further damage to transmission. You need to take it to a trans shop for diagnostic

    Dec 17, 2008 | 1995 Chrysler LHS

    3 Answers

    94 lhs heater turns on automatically hen it feel like it and blows heat a/c no longer works


    I had the same problem. It is your blower motor and I had the blower motor resister replaced and it works fine, A/C even works now!

    Aug 13, 2008 | 1994 Chrysler LHS

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    121 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chrysler Experts

    yadayada
    yadayada

    Level 3 Expert

    76846 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22246 Answers

    Jeffrey Turcotte
    Jeffrey Turcotte

    Level 3 Expert

    8567 Answers

    Are you a Chrysler Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...